1ASSP00460-2006-10 Ford Explorer Mercury Mountaineer Front Driver & Passenger Side 2 Piece Strut & Spring Assembly Set

Replaces

2006-10 Ford Explorer Mercury Mountaineer Front Driver & Passenger Side 2 Piece Strut & Spring Assembly Set TRQ SCA57055

1ASSP00460

Part Details

  • Set Quantity: 2 Piece

This part replaces:

  • Monroe 171124
  • KYB SR4137
  • Monroe 181124
  • Moog ST8611
FREE SAME DAY SHIPPING
Save 30%
List: $243.95 Save: $74.00
Only 3 left in stock
Part 1ASSP00460
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: SCA57055
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools

Part Details

  • Set Quantity:   2 Piece

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

  1. step : Removing the Wheel (0:27)
    • Loosen the five 19mm lug nuts
    • Raise and support the vehicle
    • Remove the lug nuts
    • Slide the wheel off the hub
  2. step : Removing the Strut (0:53)
    • Apply rust penetrant to the strut
    • Unclip the plastic retainer from the top of the strut
    • Remove the three 13mm nuts from the top of the strut
    • Remove the 24mm bolt from the bottom of the strut
    • Remove the flag nut from the control arm
    • Lower the control arm and lift the strut out of the control arm
    • Remove the 21mm nut from the tie rod ball joint
    • Strike the wheel knuckle with a hammer to loosen the tie rod ball joint
    • Separate the tie rod from the wheel knuckle and set it aside
    • Remove the strut
  3. step : Installing the Strut (3:13)
    • Remove the 18mm nut from the upper control arm ball joint
    • Strike the wheel knuckle with a hammer to loosen the upper control arm ball joint
    • Separate the upper control arm from the wheel knuckle
    • Put the strut into place
    • Start the three 13mm nuts at the top of the strut
    • Start the 24mm bolt into the bottom of the strut
    • Thread the flag nut onto the 24mm bolt
    • Tighten the three 13mm nuts
    • Clip the plastic retainer onto the top of the strut
    • Raise the suspension to ride height with a jack
    • Place the upper control arm ball joint into the wheel knuckle
    • Fasten the 18mm bolt onto the upper control arm nut
    • Tighten the control arm nut to 41 foot-pounds of torque
    • Place the tie rod ball joint into the wheel knuckle
    • Fasten the 22mm nut onto the wheel knuckle
    • Tighten the 22mm nut to 52 foot-pounds
    • Tighten the 24mm bolt at the bottom of the strut
    • Lower the suspension and remove the jack
  4. step : Installing the Wheel (6:51)
    • Slide the wheel into place
    • Start the five 19mm lug nuts
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Hammer
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 24mm Socket
  • 21mm Socket
  • 18mm Socket
  • 19mm Socket
  • 13mm Socket
  • 22mm Socket

  • Wrenches - Metric

  • 24mm Wrench
  • 21mm wrench
  • 22mm Wrench
  • 15mm Wrench
  • 8mm Wrench
  • 18mm Wrench


Fits the following Makes:

Year Make Model Description
2006-2010Ford Explorer Ford Explorer Front Driver & Passenger Side 2 Piece Strut & Spring Assembly Set
2006-2010Mercury Mountaineer Mercury Mountaineer Front Driver & Passenger Side 2 Piece Strut & Spring Assembly Set

Part Interchange

Brand Label Part Number
KYB SR4137
KYB Shocks & Struts SR4137
Monroe 171124
Monroe 181124
Monroe Shocks & Struts 171124
Monroe Shocks & Struts 181124
Unity Automotive 11890

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: SCA57055
Product Reviews
4.50/ 5.0 2
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
0
0
0
March 5, 2019
This product is excellent
2006 Explorer struts
March 22, 2019
I bought these for my wifes Explorer to correct a bad bounce in the front end. After getting a quote from the service department of the Ford dealership where she works, I knew that I would need to tackle this job myself. The price from 1A was unbeatable, and the video they supply helped immensely. The reason that I gave this product 4 stars rather than 5 was that the struts were missing 3 of the 6 nuts required to anchor the tops. She is thrilled with the way her Explorer rides, and Im glad to have this job behind me.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Are the TRQ struts comparable to O.E.M. as far as ride comfort and spring diameter?
March 27, 2019
10
These aftermarket struts are built to your vehicles exact OEM specifications and will fit and function the same as the originals.
March 27, 2019
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET


2006-10 Ford Explorer Mercury Mountaineer Front Driver & Passenger Side 2 Piece Strut & Spring Assembly Set TRQ SCA57055-1ASSP00460 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a vehicle with these options.