Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Paint To Match Note:
"Paint-to-match finish" refers to a smooth, paintable surface. This item is not painted. Paint offers better coverage and adhesion, but it is not necessary for installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
We're going to remove this trim panel right here using a trim tool. We sell these at 1AAuto.com. Just get in behind here. Pry this out, there's some clips, this one happened to stay in there, there's the other one. I'm going to take this clip out before it gets lost, just use some needle-nose pliers. Then we can reinstall it on here; just push it on. I'm just going to push it on this bench, push it down just like that.
Next is the cover right here. I'm going to take a flat-blade screwdriver and just pop this cover off. There's two Phillips head screws right there. Take those out with a Phillips head screwdriver. Pull the handle out of your way a little bit. Get this screw out as well. Over here there's a little cover, under here just get your screwdriver under the cover, peel it up. It's just rubber. Another Phillips head screw. Take this one out. Over here there's a little cover. Take your flat-blade screwdriver and pry underneath it, pull it out of your way. If you look up in there, there's a Phillips head screw. Take this one out. Under here, there's one more cover. Take this one off. There's a Philips head screw right here. Take this one off.
I'm going to use a trim tool and go underneath here, and just pop off the door panel and go all the way around, popping the door pins. Just like that. Once this is all loose, you can lift up on the door panel, pull it back.
I'm going to pop this inner door handle assembly in. I'll just take my trim tool and grab under here. There's some clips that hold it in. Just pop and up like this. Just like that. That can stay like that for now.
I just spun the door panel so we can see this electrical connector. There is a little tab on here, right there, so we push down on that and release the connector.
We'll disconnect this electrical connector right here. I'm going to push down on that tab and pull it out just like that. Then we're going to remove these three nuts. They're eight millimeter nuts. I'm going to use an eight-millimeter socket and extension and a ratchet. When I remove this last nut, I'm going to hold the mirror from the outside so it doesn't fall. This little nub right here with the screw on it would actually hold the mirror from falling, but it's always good to hold it just in case it does fall. You're going to push that through like that, feed the wire through, and there's the mirror.
We're going to install this mirror. Take the wiring harness. You're going to run in through that bigger hole there. Then you're going to line this up. Push it through just like that. While you're holding it, you can put this nut on. Once you get the nut threaded on, then it's safe to let go. Put these other nuts on. Then we'll take a socket, extension, and ratchet and just snug these up, not too tight. You don't want to over-tighten it, just snug like that. Now we can plug the electrical connector back in.
Sometimes you'll have one of these clips stay in the door, and we need to put it back in the door panel. We have this clip remover tool, you can get these at 1AAuto.com. You slide it on all the way, and then you just pop it out.
All right, we'll reinstall this clip. Slide it in here and just push it on like that. Reattach our master window switch electrical connector. Just plug it in the back here until it locks in place.
Now we'll take the inner door handle, we're going to line it up with the inside of the panel. Just like this.
Once that's on, slide the top part of the door panel in first into the window channel just like that. We'll make sure our door panel's lined up with our pins. It's lined up. Then we can start pushing it on.
Reinstall these two screws here. Install the screw right here. Tighten that down. I'm going to push this cover on. Install the screw right here. Now we'll pop this cover on.
Then install the screw right here. Then we can pop this cover on this way, just like that. And then this little one goes right here, gets locked in right there. Then line these retainers up and lock it in.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
