Kit Includes: (2) Front Sway Bar Links (2) Front Outer Tie Rods (1) Idler Arm (1) Pitman Arm (2) Front Inner Tie Rods (1) Front Center Link (2) Front Tie Rod Adjusting Sleeves
Specification
Drivetrain
4 Wheel Drive
Location
Front
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Application Specific Design: No modifications necessary
Anti-Corrosion Coated: Enhanced surface life
Pre-greased: No additional maintenance required
Kitted for Restored Performance: Improved road-feel and handling
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Idler Arm Bracket Assembly 1995-2000 Chevy Tahoe
How To Replace Radiator Cooling Fan 1996-2007 Ford Taurus
How to Replace Sway Bar Link 2000-06 Chevy Suburban
How to Replace Sway Bar Link 2000-06 Chevy Suburban
Created on:
Tools used
24mm Socket
Large C-Clamp
Socket Extensions
Torque Wrench
Hammer
Tie Rod Fork
15mm Socket
18mm Wrench
Jack Stands
18mm Socket
19mm Socket
Grease Gun
Tie Rod Puller
Ratchet
1/2 Inch Breaker Bar
22mm Socket
1. Remove the wheel
Loosen the lug nuts.
Raise and secure the vehicle
Remove the lug nuts and the wheel.
2. Remove the front shield
Use a 15 mm socket and ratchet.
Remove the four bolts.
3. Remove the Idler Arm
Remove the 24 mm bolt securing the idler arm to the steering linkage
Use a joint fork and a hammer to separate the joint.
Remove the three other bolts securing the idler arm.
Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
4. Install the new idler arm
Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
Bolt in the idler arm assembly into place, tightening up the three nuts.
Bolt in the end of the idler arm assembly to the steering gear.
Torque the nuts and bolts to 80 ft lbs.
Install the cotter pin.
Use a grease gun and fill the grease fitting.
5. Reassembly
Replace the shield with the four 15mm bolts.
Clip the air bag harness back in.
Put the wheel back on and lower the car
Using a star pattern torque the lug nuts to 120-140 ft lbs
Brought to you by 1A Auto. com, your source for quality replacement parts and the best source on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1A Auto dot com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to replace the idler arm on this '96 Tahoe. This is a full drive truck so it's the same as any '98, or '88 to '98 GM truck and '92 to 2000 SUV. Tools you'll need are various millimeter sockets, joint fork and hammer, a tie rod or an idler arm puller, a torque wrench, telescoping magnet and an 18 millimeter wrench.
First, using a 19 millimeter wrench or your tire iron, remove your front. Using a 15 millimeter wrench, remove this front shield. Then, we're zooming in here and this is a 24 millimeter bolt that holds the idler arm on to the steering linkage. We're going to use a joint fork, we're just going to put that right in between the joint where the idler arm and the steering linkage is, zoom out here and then, just use a good-sized hammer and just force that fork right between the joint and separate that joint. The idler arm assembly is held on by three bolts. You can see the backside of them there. You get to them through the frame through access holes right there. You can see my wrench is through one and then the other two are right near them.
We'll speed up going through and removing those three bolts. Note have a telescoping magnet available for when you drop those bolts into the frame as I do a couple of times. What I'm doing here is pulling the idler assembly away from the frame, and at the same time with the other hand, pushing the idler arm up and away from the steering linkage, or actually pulling the steering linkage down. Eventually it comes loose enough and comes right out. This is a 24 millimeter. You want to use this puller and this is a rubber gasket here, pretty much just have to force it into your puller, pull that right off. My new one; right back into place.
The trouble you run into is when you try to put this back together, right back and these two go to the back when you try and put this back together, this is a lock nut and wind up turning the shaft. What I'm doing, I got a big old bolt from another project. I put that on there and what happens this will go in enough and when I hit that other nut, it'll start pressing this on to the shaft. Then, I can use the arm itself to pull the shaft. I put my lock nut back on. Using a magnet, I took out my other two bolts so I have that top one in. I'm going to use an extension and hold that bolt in place, assembly up in here and hang in on that bolt.
I will put the nut up on that bolt and then basically repeat the step for the two bolts, put them right in to my extension with my socket, feed them through. See the bolt come through, put it on to the assembly and put the nut back on and then same thing with the third one. Feed it through, see the back of my head and then, put the nut on. Before I tighten those up, I'll turn my attention over to the steering gear. Here I pull the steering gear down and on to the joint for the idler arm and then just put the nut on hand tight. Now we'll go back to tightening up those three bolts. You want to use torque wrench and tighten them up to 80-foot pounds. This 22 millimeters and tighten these up to 80-foot pounds as well. Just a little tighter so we can fit that cotter pin through.
We'll put a grease gun in there and make sure we hit that grease footing to get it properly lubed up. Put your shield back on real quick with the four 15-millimeter bolts. Over here, we're just going to put that little pin back into the harness that was holding our airbag sensor there. We'll speed up putting the tire back on. Put on the lug nuts, tighten them a little bit, then lower the car down and torque them to about a hundred twenty to a hundred forty foot-pounds and then put your cap back on.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll free 888-844-3393. We're the company that serves you on the Internet and in person.
Tools used
Flat Blade Screwdriver
8mm Wrench
8mm Socket
Ratchet
1. disconnect the battery
Use your 8 mm socket and ratchet to disconnect the negative battery terminal
2. Remove the radiator cooling fan shroud
Pry up the fuse box and move it out of the way.
Remove the 8 mm bolt securing the fan shroud.
Disconnect the wiring harness from the radiator fan and un-clip the wiring from the back of the shroud.
Remove the fan.
Repeat with the second radiator fan.
3. Install the new radiator fans.
Put the fans down into the engine bay next to the radiator.
Bolt the fans into place.
Reconnect the electrical harnesses and clip them back onto the shroud.
Clip the fuse box back into place.
Reconnect the negative battery terminal.
Brought to you by 1AAuto.com, your source for quality replacement parts, and the best service on the internet. Hi. I'm Mike Green. I'm one of the owners at 1AAuto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years' experience restoring and repairing cars and trucks like this, to show you the correct way to consult parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video we are going to remove and reinstall the radiator fans in this 2001 Ford Taurus. The fans didn't need repaired in this car. I'm just doing the video to show you how to take them out and put them in. The only tools you'll need are an 8mm socket and ratchet and a flat blade screwdriver. We're going to disconnect the battery here using an 8mm socket. You'll want to use a regular screwdriver. There is two tabs, you'll want to pull out on the tab, and pull up on this fuse box. This will just go up and out of the way a little bit. You'll see there is an 8mm bolt right here. You can see right down there is a plug for your radiator fan. All you're going to do is pry out lightly here and pull that plug off. You want to pull these pins. You can see here's one of the pins out. Pull these pins out of the fan shroud. Okay. We'll kind of speed through that process of unplugging the fan and removing the harnesses from the clips, and then finish out removing the 8mm bolt. Get this up out of the way. Pull this fan up. That just comes out of the bottom. Lift it out.
With this fan I've done the same thing. I already loosened this bolt. I've already unplugged it. I'm just going to take that bolt off. I'm going to pull it out. Then I'm going to slide over to where this other fan came from. It's going to be a fight with all the wiring. Slide it up and out. Slide this on over. It has two feet that have basically a cross pattern on it. If you look down in you can see right there, that cross right there, that's where one of the feets goes. Then that cross right down there is where the other one goes. You put the fans down in, and you kind of just work them back and forth a little bit. You find where they go down in, and then that 8mm bolt lines up. Then tighten up that bolt. Tighten up this 8mm bolt. Reconnect the wiring harnesses for the fan. Make sure everything's routed correctly. Put the fuse block back into place, reconnect the battery, and you should be all set. The second fan, slide it down in, just pull the wiring out the way kind of. The same thing on the feet. This goes down in here into place. Tighten up your 8mm bolt. This back into place now, and then the pins connect them. Put the harnesses back into their places. Connect the battery one more time. You should be all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts, and the best service on the internet. Please feel free to call us toll free at 888-844-3393. We're the company that's here for you on the internet and in person
Tools used
Reciprocating Saw
Hammer
Torque Wrench
14mm Socket
Jack Stands
Ratchet
22mm Socket
1. Removing the Wheel
Remove the hub cap by loosening the lug nuts
Remove the lug nuts and tire
2. Removing the Stabilizer Link
Using locking pliers to clip onto the top of the stabilizer link
Then remove 14mm bolt from bottom of the stabilizer link
Remove the stabilizer link with a hammer or reciprocating saw
3. Replacing the Stabilizer Link
Put the stabilizer piece back into place
Use four washers, four grommets, and a tube
Use a jack stand to help push it through till it appears through the top
Tighten the 14mm bolt on the stabilizer link
4. Replacing the Wheel
Put the tire in place
Replace and tighten each lug nut
Torque each lug nut in a crossing pattern to 100 ft/lbs
Torque the center hub nut to 160 ft/lbs
Replace the hub cap and tighten the lug nut caps
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a sway bar link on this 2002 Chevy Suburban, and it's the same part and similar process on these Suburbans from 2000 and 2006. We show you on the passenger's side, but on the driver's side it's the same procedure. The items you need for this include a new sway bar link from 1AAuto.com, a 14mm and 22mm socket and ratchet, locking pliers, a hammer, and a reciprocating saw depending on the condition of your vehicle.
Remove your hubcap by loosening up these lug nut caps and pulling the hub cap. Now, you want to remove the lug nuts. If you don't have air powered tools, you want to do this while the vehicle is on the ground. You can loosen them preliminarily, raise the vehicle and remove the lug nuts the rest of the way, and pull the wheel out. Using locking pliers, clip on to the top of your stabilizer link, and then remove this 14mm bolt. We'll just fast forward as Mike does this.
Now, you want to just hammer the link through. If the link doesn't move, you may have to use a reciprocating saw and cut it. Up top is the old part; below is the new part from 1A Auto. You can see they're identical, and they'll fit exactly the same. You want to put your stabilizer link back into place, starting with a washer and a grommet, then through the hole, then another grommet, then a washer, then the tube; then, before going through the next hole, another washer and grommet; then, on the top another grommet and another washer, then the nut.
Here, we just put the jack underneath the link. That's just to push it up through and compress the washers a little bit so that you can get the nut on the other end. Once I get another nut on, you'll see I just release the jack. You want to obviously be supporting the vehicle with jack stands, and then use your jack to push the bolt of the link up through. Then, you want to tighten up the sway bar link, and you basically want to tighten it up until the rubber bushings are compressed enough so that they're the same diameter as the washers.
Put the wheel back in place, then replace each of your lug nuts and tighten them up. You want to tighten them preliminarily, lower the vehicle, then tighten them the rest of the way. Torque each lug nut in a crossing pattern to 100 foot-pounds. Replace the hubcap, and just tighten up those lug nut caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Reciprocating Saw
Hammer
Torque Wrench
14mm Socket
Jack Stands
Ratchet
22mm Socket
1. Removing the Wheel
Remove the hub cap by loosening the lug nuts
Remove the lug nuts and tire
2. Removing the Stabilizer Link
Using locking pliers to clip onto the top of the stabilizer link
Then remove 14mm bolt from bottom of the stabilizer link
Remove the stabilizer link with a hammer or reciprocating saw
3. Replacing the Stabilizer Link
Put the stabilizer piece back into place
Use four washers, four grommets, and a tube
Use a jack stand to help push it through till it appears through the top
Tighten the 14mm bolt on the stabilizer link
4. Replacing the Wheel
Put the tire in place
Replace and tighten each lug nut
Torque each lug nut in a crossing pattern to 100 ft/lbs
Torque the center hub nut to 160 ft/lbs
Replace the hub cap and tighten the lug nut caps
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a sway bar link on this 2002 Chevy Suburban, and it's the same part and similar process on these Suburbans from 2000 and 2006. We show you on the passenger's side, but on the driver's side it's the same procedure. The items you need for this include a new sway bar link from 1AAuto.com, a 14mm and 22mm socket and ratchet, locking pliers, a hammer, and a reciprocating saw depending on the condition of your vehicle.
Remove your hubcap by loosening up these lug nut caps and pulling the hub cap. Now, you want to remove the lug nuts. If you don't have air powered tools, you want to do this while the vehicle is on the ground. You can loosen them preliminarily, raise the vehicle and remove the lug nuts the rest of the way, and pull the wheel out. Using locking pliers, clip on to the top of your stabilizer link, and then remove this 14mm bolt. We'll just fast forward as Mike does this.
Now, you want to just hammer the link through. If the link doesn't move, you may have to use a reciprocating saw and cut it. Up top is the old part; below is the new part from 1A Auto. You can see they're identical, and they'll fit exactly the same. You want to put your stabilizer link back into place, starting with a washer and a grommet, then through the hole, then another grommet, then a washer, then the tube; then, before going through the next hole, another washer and grommet; then, on the top another grommet and another washer, then the nut.
Here, we just put the jack underneath the link. That's just to push it up through and compress the washers a little bit so that you can get the nut on the other end. Once I get another nut on, you'll see I just release the jack. You want to obviously be supporting the vehicle with jack stands, and then use your jack to push the bolt of the link up through. Then, you want to tighten up the sway bar link, and you basically want to tighten it up until the rubber bushings are compressed enough so that they're the same diameter as the washers.
Put the wheel back in place, then replace each of your lug nuts and tighten them up. You want to tighten them preliminarily, lower the vehicle, then tighten them the rest of the way. Torque each lug nut in a crossing pattern to 100 foot-pounds. Replace the hubcap, and just tighten up those lug nut caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
PSA64942
In Stock
Product Reviews
Loading reviews
4.40/ 5.015
15 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
9
5
0
0
1
T
October 20, 2020
fit great!
Quality service and parts
S
December 30, 2020
I've bought many parts from you guys not just fory personal vehicles but also for many of my customers as well,still have notta one complaint in quality,price and service ,if there would be one complaint I do have it's that damn postman can't get upy driveway fast enough!!! Keep up the great work guys ,
Sincerely,
A happy satisfied customer
Steven Kuntz
Front suspension for Yukon
Jacob
March 28, 2021
Arrived on time and had all parts I really needed to tighten up my front end. I also saved a lot of money by ordering from 1A Auto. It was definitely worth it. I will continue to order from here. Thanks again!
Good quality parts
Jesus
April 12, 2022
Everything fits my gmc
Mike
October 25, 2022
Correct parts..fast delivery
94 K1500
Joseph
March 6, 2023
94 K1500, Great parts exact fit, drives like new again.
Satisfied
K
March 15, 2023
It works ,
So far great
Peter
May 6, 2023
Everything fit well on my 99 Tahoe ls
So far great
Peter
May 6, 2023
Everything fit well on my 99 Tahoe ls
Jeannie
August 9, 2023
Hubby says truck drives Much better!! Great Customer Service!
Leonard
August 17, 2023
Was everything I needed thx
Aji
October 26, 2023
Good equipment does the job.
New riding 98 Sierra K1500. Perfect addition to rebuilding my truck.
Jim
November 22, 2023
All parts shipped and arrived BEFORE expected date. Fit perfect. Made my truck ride like new. ********** 10 stars.
Jason
February 13, 2024
Fitment price and shipping fast
Tierod
Carlos
March 3, 2024
One tie rod has pitch not machined correctly
Now I have to wait again to complete my repair
?????
Customer Q&A
I have a 97 k1500 5.7 need rebuild front end . Whats best parts for job. That will last as ???long as stock ones have thanksJanuary 21, 2020
Richard J
10
These parts are built to your vehicle's exact OEM specifications with high quality materials. We back them also with our Lifetime Warranty. Thank you for the inquiry!
January 21, 2020
Andra M
Does this 11 piece front end kit fit 97 silverado k1500 5, five lug?July 16, 2023
John D
10
That year Silverado and Tahoe should have same front end parts yes.
July 17, 2023
Terrance R
10
Yes, this kit will fit your vehicle.
July 17, 2023
Meghan R
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.