Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Steering & Suspension Kits
Part Details
Product Features
TRQ drivetrain kits are manufactured using premium raw materials to restore original performance. Each TRQ drivetrain component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the service life of your drivetrain, TRQ recommends replacing wheel hubs, bearings, and constant velocity (CV) drive axles at the same time to ensure even wear of components and improved ride comfort. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Our direct fit gas-charged shock absorbers help restore your vehicle's handling and ride quality to just like new.
Replacing struts used to require specialized tools to compress, remove, and transfer the old spring and mount. Our Pre-assembled, complete strut & spring assemblies come with all new parts and make the job much quicker and easier for the do-it-yourself mechanic.
Strut & spring assembly contains:
Our steering and suspension kits are offered in a variety of options to best fit your repair needs and your budget.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
In this video we show you how to replace a front hub on this 2006 Chevy Malibu, same as any 04 to 08 Malibu as well as the Pontiac G6. You know if you have a bad hub if you jack the front wheel off the ground, and you can grab the top and bottom of the wheel and shake it and feel play and then you can also grab each side left and right, shake it and feel the same play. That kind of four-angled play is usually because of a bad hub. Tools you'll need are jack and jack stands, various sockets 13 to 19 mm plus a 35 mm socket with ratchets and extensions. You'll need a breaker bar or a pipe for some extra leverage, flat blade screwdriver, large hammer, wire brush and a torque wrench.
Start out by using a 19 mm socket or wrench and loosen the plastic covers and then remove the wheel cover. You're going to remove the lug nuts, and if you don't have air tools, you'll want to have the wheel on the ground, loosen the lug nuts. Also at this point, you'll want to loosen that 35 mm hub nut. I do have the benefit of having an impact wrench, so I'm able to do that afterwards, but if you don't have an impact wrench, you want to use a breaker bar and a 35 mm socket and loosen that center hub nut now while the wheel is on the ground.
Grab hold of the steering knuckle and turn it to make it easier to reach the back of the caliper. The first thing we're going to do is remove these two bolts here. These two bolts are 14 mm and they should come off pretty easy. I'm just going to speed it up as I remove those two bolts. Now your disc should come off, but since there are some pretty decent ridges here. What you want to do is take a good size screwdriver and pry out with this hole and that kind of loosens up the caliper, and the caliper comes right off. Put it up there for now, and you can just kind of pry out your pads.
Now we need to remove this caliper bracket, so we'll remove two 15 mm bolts here and here. These are going to be somewhat tighter, so I'm going to use my ratchet. If you have a breaker bar, that's the best thing or use a piece of pipe, put it on your ratchet, gives you extra leverage and it comes apart pretty easily. The same thing top one. Get it started.
I'm just going to speed it up here again as I remove those bolts. I found that once I turned them probably three or four turns then they actually came out by hand. Comes over, pulls right off. Right up here is your ABS harness with a little tab pull that down, disconnect that, then just use a screwdriver, push these tabs down and pull the plug off. I take a 35 mm bolt here for the hub. As I said earlier, if you don't have the benefit of impact tools or air tools, you'll want to loosen this hub nut while the wheel is still on and the vehicle is on the ground.
Now your axle you don't want to make it a habit to just beat on this mercilessly with the hammer. What I do is I give it one good tap, and I watch closely, and if that axle moves with one good hit, you know it's broken loose. You don't have to worry too much about it. Okay, the axle moved, so I should be able to get it apart, no problem. If the axle doesn't move with the tap of a hammer, then you'll need to use an axle puller which bolts onto your lug and then use the bolt to push the axle through.
Next we're going to remove the three bolts that hold the hub. Okay, one is up there, one there and one around the back side is kind of hidden tucked right in there. These bolts, especially the top one, you're going to want probably 3/8 drive tools, because they're skinnier, and they allow you go get in there. I'm going to get a pretty good-sized flexible handle and try that. I can use my pipe for a little more leverage. These should come apart pretty easily. At this point I'll speed it up. Use the pipe for the extra leverage, get the bolts loosened up and then you can go at it with the ratchet and remove them the rest of the way. You'll want to turn your steering knuckle so that you can reach the third nut on the backside and then just remove those bolts. Once you have the bolts out, good there. I'm going to speed it up here. Basically you just hit it side to side, up and down and you'll see the hub start to separate from the steering knuckle and then eventually it comes loose, then you can pull it right off. Take the hub off, and your backing plate off. Just kind of wire tied my brake caliper up there. Use a screwdriver and a wire brush to just kind of clean the corrosion from the steering knuckle.
It may need a light coat of grease. It really helps things go back together. You can use some penetrating oil or just regular oil. Take your backing plate and I'm just going to put that in place. Your connector one you want to have that up toward the rear, through the backing plate and put your connector up and through and push on the CV a little bit. Make sure that your electro connector is toward the rear and get the hub onto the axle, spin this around in the correct position, put one of your bolts through. Push everything into place. I'll speed it up here again. You push the hub on, make sure it's in place correctly, start the other two bolts. All the time you're doing this just make sure that ABS wire doesn't get pinched in there anywhere and tighten up those bolts.
Make sure your wire is pulled through, and it's free and put the receptacle right up and clip it into place and I'll reconnect it. Tighten these bolts to hold the hub to the steering knuckle with 65 foot pounds. I'll just speed it up here. Turn the steering knuckle and tighten up the other two again to 65 foot pounds.
New rotor from 1A Auto. Put it on. Take a lug nut. Bolt it into place here. Now take your bracket and it goes basically between the knuckle and the disc, put your bolt in, find its way. These bolts you want to tighten up to 85 foot pounds. Put this one on the front. You want to make sure that your slides are pushed in here, bring your caliper down right on top, two bolts. These two bolts you want to tighten to 35 foot pounds. Once you have the wheel back in place, then you put the lug nuts on by hand, and then I'm just use my impact wrench to just tighten them up preliminarily.
Now with the vehicle on the ground, torque the lug nuts to 100 pounds using a star pattern, now torque your center hub nut, the 35 mm nut with 159 foot pounds, put your wheel cover back on, there's a hole for the valve stem, then use a socket to tighten up the retainers. Last but certainly not least before you drive your vehicle, make sure you pump the brakes a bunch of times, get the pedal to feel nice and firm when you have to reset those caliper pistons, then do stops from five and ten miles an hour before you road test the vehicle.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
Tools used
Tools used
Okay, friends, before we get started, make sure you safely raise and support your vehicle so your wheel is off the ground. Once you've done that, we're gonna remove all five of our 19-millimeter lug nuts. Remove your wheel. Just to say, we're gonna be servicing a lot of things on the front end of this vehicle, so if you see anything that's taken apart that isn't necessarily in the steps that you need to see, well just don't really pay too much attention to that, and just follow the steps ahead.
All right, now that we've got the wheel off, let's go ahead and remove the caliper bolts from the caliper bracket sliders. Using a small pry bar, I'm just gonna get right in between here and see if I can apply a little bit of pressure and push back this caliper a tiny bit. You can use a wire tie or even a bungee cord. Let's get our pads out of here. Remove your caliper bracket bolts, one here and one up here. Hold that bracket. Now it's gonna be time to get the rotor off of here. If you find that it's stuck on the bearing, just give it a couple loving bonks around this area here. Just be careful for your studs, and definitely don't hit the braking surface.
Now we're gonna use our 36-millimeter socket and remove our axle nut. I always like to spray down the area with some penetrant. So next, we need to push our axle out through our bearing. To do that, you never want to use the hammer directly on your axle, because you could peen over the threads, and of course, that's gonna cause an issue. What I would like to use is a center punch. Come right in the middle here, give it a couple loving bonks. If you don't have a punch, just go ahead and use the original nut here. Put it on there so it's pretty much flush, and then you can go ahead and give it a couple bonks that way. When you do that, you don't have to worry about damaging the threads.
Next, we need to remove our outer tie rod and nut. If you notice when you're trying to take off your outer tie rod and nut that the stud was just spinning inside your knuckle area, use some nice long pliers like this. And we're just gonna try to squeeze that outer tie rod end up against here. Try to reset that stud into the knuckle. Now I'm gonna continue on by loosening this. If you wanted to apply a little bit of heat to your nut, it might be helpful as well. Obviously, if your tie rod's in the same condition as ours, where the boot's just pretty much completely ruined slash gone, just go ahead and replace your outer tie rod end. All right, let's get this out of here.
Now it's time to get our ABS wire disconnected. Now we need to separate the knuckle from the actual strut itself. To do that, we're gonna remove these 18-millimeter nuts, and then push out these bolts. Get this out of the way. I'm just gonna start these back on so we don't damage the threads of the bolts. Now let's continue with a hammer. Give these a couple loving bonks. If you want to use a little bit of penetrant, it's probably a great idea. Now let's separate the two of these. Push in on that axle a little bit.
Now, with the bracket loose, I can see these right here. I'm just gonna give them a nice squeeze, see if I can get it to break free from the actual bracket itself. There we are. We'll set this aside. So now we can turn the knuckle any direction we want, and we can fully access these bolts. That's great. Use your 13-millimeter, remove all three. Let's take one of our bolts. We're gonna put it right through here with the knuckle in there. Let's spray down the area with some penetrant. Continue on with your hammer. Give this a couple bonks. We need to break it free from the knuckle.
Looks like it's barely starting to move. Now that we've got it starting to come off, let's remove that bolt. Continue on. There it is, friends. It's important to take a look inside the knuckle area. If you see any of this, like what I have here, that means that your bearing separated upon removal, and we need to continue getting the rest of it out. Now we need to clean up the mounting area for the new bearing. If you were to look along this area right here, I can see a lot of corrosion and a lot of raised areas. I need to make sure that this is nice and smooth, but we don't want to stop there. We need to continue on to this inner surface here, and make sure we get rid of any of the underlying corrosion that's there as well.
Once you have the area cleaned up, go ahead and use a little bit of copper never seize along all the areas that you just cleaned. Let's clean up the threads on the bolts. I always like to use a little bit of thread locker. We'll call it your prerogative. Now we're gonna take those bolts, the backing plate, and our brand new wheel bearing, and get ready for our install. First, I'm gonna take the backing plate, I'm gonna line it up just like this. You want to make sure that the slotted area is where your caliper is gonna go. Take your wheel bearing, carefully put it through, but you want to make sure that the wire area is facing up and out towards the rear of the vehicle. Make sure it's not caught on anything, of course. Line up all three holes, close as possible at least, and then start in all three bolts. We'll snug them up, and then we'll torque them to manufacturer specifications.
Okay. All three of those are snug. Now we're gonna torque them. Torque this to 85 foot-pounds. Something that we need to pay attention to before we go ahead and reinstall the knuckle up here is the corrosion that comes right along this area. If you have any corrosion along your knuckle, just make sure you get that off. I always like to put a tiny bit of copper never seize inside the bearing where the axle's gonna go. Let's get the axle back inside the bearing here. There we are. Bring the knuckle up, and now we're gonna start in our bolts. These bolts are gonna go from the front towards the rear. Let's get our ABS wire on here. Start on both of these nuts. We'll bottom them out, and then we'll torque them to 89 foot-pounds.
Connect in your ABS wire. Make sure it clicks in and locks, and then secure it right here. Let's put in our tie rod. Go ahead and put that nut on there. Now I'm gonna snug it up, and then we'll torque it to manufacturer specifications. Let's torque this to 18 foot-pounds. And now we need to turn it an additional 90 degrees, which basically means a quarter turn. So I'm gonna start my ratchet right here, and then I'm gonna come right along so it looks like this. That's pretty decent. If your tie rod stud has a castle nut like this, you want to make sure that the castle nut slot is lined up with the stud itself. Go ahead and put through a cotter pin if you have one, and of course, lock it in.
Next, we're gonna put on our axle nut. If you want to use a little bit of thread locker, we'll call it your prerogative. We'll bottom this out, and then we'll torque it to manufacturer specifications. The best way to torque this is to go ahead and take a nice long pry bar like this, put it flat across the studs, that way there the hub can not turn. Now we're gonna torque this to 159 foot-pounds. Torqued. Let's go ahead and put a little bit of copper never seize on our hub.
Time to install the rotor. And I always like to hold it on with a lug nut. That way, there can't wiggle around. Let's go ahead and get the bracket on here. I always like to use a little bit of thread locker on my bolts. Start them both in, we'll snug them up, and then we'll torque them to manufacturer specifications. Torque these to 96 foot-pounds. Go ahead and carefully put this in here. Put on the outer pad as well. Now we're gonna slide this right over the sliders, and of course, over the pads. Line up those sliders. We'll put in our slider bolts.
Now we're just gonna bottom these out, and then we'll torque them to 26 foot-pounds. Make sure you clean down your entire braking surface, just in case you have any fingerprints on it. All right. Let's just double-check everything that we fixed here. Looks great. We'll get the wheel up on. We'll start all the lug nuts, snug them up, and then we're gonna torque them to 100 foot-pounds. All right, 100 foot-pounds. Torqued.
Tools used
Tools used
Brought to you by 1Aauto.com, your source for quality replacement parts and the best service on the Internet. Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the rear shock on this 2007 Pontiac G6. Pretty much the same for any 2005 to 2010 G6, as well as the Saturn Aura. We'll show you the right hand, or passenger side. The driver's side is the same procedure, and we always recommend you replace your shocks in pairs. The only thing you'll need, you will need a jack and jack stands. You will need 13, 19, and 21mm sockets, also as well as a ratchet, an extension, and probably a breaker bar or a pipe for some extra leverage.
Take it, and depending on what wheels you have, this has wheel covers, so you unscrew the caps, and then the wheel cover comes off. If you don't have the benefit of air tools, you'll want to loosen the lug nuts with the vehicle on the ground, then raise and secure the vehicle, and then remove the lug nuts, wheel, and tire. Two 13mm nuts hold the shock at the top. We'll fast-forward here as we remove those two 13mm nuts. A 21mm bolt holds the shock at the bottom. We'll use a 21mm ratchet. We'll put a pipe on there for some extra leverage. It made it come off really easy. He probably can get it off easily enough with just the ratchet.
Our car is new enough that this shock is not worn out at all, so we're just going to reinstall the original one. We just wanted to show you this video, just so you know how to do it. The shocks we sell at 1A Auto are great replacements. You can see, you put the shock back in place, and then start those two nuts on the top. I will fast-forward, as we finish putting those nuts on. I then start the bolt at the bottom, and tighten it up. The bottom bolt, you want to tighten to probably about 45 to 50 foot-pounds, and the top bolts, you want to tighten up afterwards, between 20 and 25 foot-pounds. Keep the speed up here, as we put our wheel and tire back on, and just start the lug nuts on there by hand first, then tighten them preliminarily. With the car back down on the ground now, we'll tighten the lug nuts to 100 foot-pounds, using a star pattern.
Last but not least, put our wheel cover on there, and then put the caps on carefully, only using hand power to tighten those caps up.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
In this video, we're going to show you how to replace a front stabilizer link. The symptom of a bad stabilizer link is if you're hearing a clunking in the front of your car, but when you go around a curve, either left or right, the clunking seems to go away. That's usually a sign that your stabilizer link is starting to loosen up. Tools you'll need are 8mm to 19mm wrenches as well as a hammer.
Turn your wheel all the way to one side or the other. Then you can reach in behind and you can see it here. This is the top of your link. You can reach in behind and grab that with your hand and shake it back and forth and if you can duplicate that clanking or rattling sound then that's what you need to replace.
Start out by using a 19mm socket or a wrench and loosen the plastic covers and then remove the wheel cover. If you don't have the benefit of air tools, you'll want to loosen the lug nuts up while it's on the ground, then raise and support your vehicle and then remove the lug nuts and the wheel.
Right here is our stabilizer link. Use a little bit of penetrating oil on the upper and lower, let that sit for awhile. We've got an 18mm wrench on the bolt and 8mm wrench on the end of the shaft there. It looks like it actually coming loose, there goes that bolt. Get that started. Put this on there and I'm going to put this one on down there and same thing. Here's a close up look. I've got the 18mm wrench on there. The 8mm wrench is just holding that stud in place and I just keep flipping back and forth with the larger wrench, grabbing onto the nut and removing it. I'm just going to speed up the tape here. It takes a little while to get these things apart. It's a tedious task of getting the wrenches in there, holding it with the smaller wrench and then using the small one and then just angling the larger wrench in there as best you can. Eventually it comes apart.
Here's a new link from 1A Auto. Iit's a little bit different but it actually makes it easier to install. You'll need a 15mm wrench to hold this on that side and then a 19mm socket and ratchet to put the bolt on. We're going to put down in. It mounts in just like your original. Start the locking bolt on here and we'll start the locking bolt down here. Up top, I put my 15mm wrench through from the backside and then a 19mm socket and ratchet. I'll just speed it up as I tighten it up with the ratchet and you want to get it nice and tight and probably 40 to 45 foot-pounds. Then continuing on down to the lower, it's the same as taking it apart. You really can't get a wrench in there or a ratchet in there so you just have to use a wrench. I used the 15mm wrench to hold the stud and then a 19mm wrench to tighten up the nut and it just takes a little while and, then, again, tighten it up between 40 to 45 foot-pounds.
Once you have the wheel back in place then you put the lug nuts on by hand and I just use my impact wrench to just tighten them preliminarily. Now with the vehicle on the ground, torque the lug nuts to 100 foot-pounds using a star pattern. Now put your wheel cover back on, there's a hole for the valve stem then use a socket to tighten up the retainers.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends, before we get started, the first thing that I want to mention is you want to be safe. So have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So come right underneath here, this is where you're going to support the vehicle in the front. Now with the front of the vehicle safely raised and supported, we're going to remove all 5 of our 19-millimeter lug nuts. Remove your wheel. Now that the wheel is off, we have a nice clear view of our front strut. With that said, anything that you're going to be removing bolts or nut-wise, you want to of course, spray it down with some penetrant.
First, what I like to do is remove the sway bar link from the front strut. So I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Let's get the brake hose off of here. What we want to do here is just kind of move this brake line a little bit so we can give some slack between the stud and the strut, that way there we can lift this right up and out.
The next thing we need to do is loosen our 36-millimeter axle nut. The reason for that is because when this knuckle is going to want to pull away from the strut, we don't want to put a tug on any of our axle boots. A little bit of penetrant. The next thing you would want to do is either with a center punch, come right into that little dimple and just try to drive this axle into the bearing a little bit, just to give a little bit of slack, or of course, if you don't have a center punch, just put the nut so it matches up evenly, give it a couple loving bonks this way. That's nice and loose.
Next, we're going to remove our 18-millimeter nuts located right here and there. They hold the knuckle to the strut. Grab this bracket, carefully set it aside. These bolts right here are actually going to have to be forced out of the knuckle area. So what I always like to do is just take those nuts and I'm going to start them back on there, a few good threads, and you want to make sure that we're not going to damage the thread of the bolts. Give it a couple of loving bonks. Keep your ABS wire clear, do the same thing to the other one.
If you look at these bolts, you can see they're both the same, and if you look, you can also see that it's splined. That's the reason why it was stuck inside the knuckle.
Now we're going to carefully try to separate these two, but we want to make sure that this doesn't come down too far because once again, we don't want to put a tug on our axle boots, and we definitely don't want to put a tug on our brake line. If you want to have a bungee cord or something that's going to hold it at least away, but safely, that's up to you. There we are. I'm just going to set this right like that. Now we need to get under the hood. Now that we have the hood up, you have a clear view of the strut tower here. With that said, you don't want to touch this center nut. We're only going to remove these three, but when we remove all three, we want to leave one on there just a couple of threads for safety, and then we'll get under, we'll hold onto the strut and then we'll remove that nut.
If for some reason your strut didn't drop down when you removed all three of your nuts like that, it's because it's probably frozen along this area here into the strut tower. Use a little bit of penetrant and then carefully bonk right along here until it finally breaks free. Down like this, I'm just going to hold onto that strut, remove that last nut, and then I can remove it. There it is, friends. One thing that's always a great idea before you go ahead and try to put your new strut into the vehicle, is just line up the strut cap with the way the original was. So a match up from the bottom, make sure it's facing a straight line, and then just set these where they need to be. You can do that fairly easily by just holding the bottom and then turning the cap itself. Okay, friends, now it's going to be time to get our brand new front strut in here. As we do this, I like to mention that I always like to use a little bit of thread locker right on these studs. We'll call it your prerogative, but I recommend it. When we put this in, we want to make sure we line up the bolt holes with the studs coming out of our strut itself.
We'll start on all of our nuts, and then we'll snug them down and torque them to manufacturer specifications. Something that's important to make sure that I mention before we go ahead and put our knuckle up into the strut, is if you were to look along the backside of the knuckle, you might find that there's a lot of corrosion buildup. That's due to the fact that somebody made the knuckle out of aluminum and they put it in with the steel. When you have aluminum with steel, it just corrodes and that's what happens.
So feel along the back. If it feels as though it's raised, you need to make sure you take a chisel or whatever you might happen to have and clean that out. Now that I've got that knuckle cleaned up, let's go ahead and put this up so it's going to line up the bolt holes. Obviously, you want to clean up the threads on your mounting bolts. Something I always like to use is a little bit of red thread locker, we'll call it your prerogative. Go ahead and start those through from the front to the back. Grab your two mounting nuts and of course, your bracket for the ABS wire, start it on there. We'll start these nuts, we'll bottom them out, and then we'll torque them to manufacturer specifications.
Torque both these nuts to 89 foot-pounds. Let's get our brake hose back in there. It slides right into this little groove, and then of course we'll tighten it up. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. After you've bottomed out your axle nut, torque it to 159 foot-pounds. I like to put a bar straight across these studs like this, you want to be careful and make sure it's flat and not at an angle because you don't want to damage your threads on your studs.
We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued. Now it's going to be time to make sure we go ahead and torque these down. Before we do that though, you need to make sure you have your wheel on the ground with the weight of the vehicle. Let's torque them to 18 foot-pounds.
Tools used
Okay, friends. The first thing you need to talk about anytime you're working on your vehicle is safety. You want hand and eye protection. With that said, safely raise and support your vehicle so the wheels are off the ground. Once you've done that, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel. Now that we have the wheel off, we have a clear view of our caliper and our rotor. What we need to do first is get the caliper out of the way and then we're going to remove the rotor. Looking at the backside of the caliper, you're going to see two mounting bolts, one located right here, and one located up top. Remove them both and get the caliper out of the way. Remove your caliper. Carefully set it aside. Let's go ahead and get the rotor off of here. And now, we have a clear view of our bearing. Coming from the backside of the bearing, you want to make sure that you remove your ABS wire and be very careful with it because it's extremely delicate. Grab this tab, pull it down, check your wiring. Make sure you don't see any funny colors.
Next, we're going to take some penetrant spray and spray down all of our mounting studs. I always like to go around the center as well. Now, we're gonna use a 15-millimeter socket and remove all four of our mounting nuts. Now, we're going to take a hammer and we're going to try to bonk from the backside of this and just try to help it out. Once it starts breaking free in one direction, we'll come from the other side a little bit and just keep going until it comes out. Looks like it started to move. Grab your bearing, remove your backing plate. There it is, friends. Now that's out of the way, let's clean up the mounting surface. Spray down the area with a little bit of copper never-seize. Before you install your backing plate, make sure you double-check both sides to make sure there's no raised areas that are going to be between mating surfaces. Once you're sure, go ahead and take your bearing, put it through the backing plate, put it through your knuckle, and then go around back and put on those mounting nuts. Little bit of threadlocker. Now, we're going to start on all the nuts. We'll bottom them out and then we'll torque them to 47 foot-pounds. Criss-cross.
Let's get our ABS wire reconnected. Click it in, give it a nice tug. It must be secure. Use some copper never-seize. Make sure you clean the backside of your rotor, where it's going to be mating up against this hub right here. Once you've done that, go ahead and put it on. I always like to start on a lug nut to hold the rotor from moving around. Let's grab the caliper, remount it on here. It's always a great idea to use a little bit of threadlocker on your bolts. Torque these bolts to 96 foot-pounds. Wheel up on here. We'll start on the lug nuts and then we'll torque them down to 100 foot-pounds. Let's torque these to 100 foot-pounds in a criss-cross manner. Torqued. Go ahead and pump up the brake pedal. Let's go ahead and check and top off our brake fluid.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front stabilizer link on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. Not a difficult procedure. You will need jack and jack stands, and you'll want to jack up both front wheels off the ground and support it with jack stands. Then you'll need a lug wrench or a 19mm socket with a ratchet, maybe even a breaker bar and a pipe for some extra leverage. Then, after that, you'll just need two 18mm wrenches, one of those 18mm will have to have an open end.
Start out by using just a socket to loosen the lug nut covers, or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools, just start with the vehicle on the ground, loosen the lug nuts, then raise and secure the vehicle, and move the lug nuts from the wheel and tire.
Use an 18mm wrench to grab on to the nuts, part of the stud of the stabilizer link, and then use an 18mm socket, loosen up the nut, and then it comes off. Here's the fun part of the repair. You pull that down out of the way, and you can see the other end of the link right there. Put the 18mm wrench on the nut that's in the shaft, just like before. Then, there's not really enough room to get a ratchet back in there, so you basically just have to take a wrench and slowly, carefully, one eighth of a turn at a time, and I'll fast-forward the video as we do that.
Then, just reinstall the link as you took it apart. Go ahead and speed up as we tighten up that lower nut, and like I said before: it's not all that difficult; it just takes quite a bit of time because you can't move that nut too far each time.
Bring the sway bar link back into place, and should you possibly feel the need to replace those sway bar links, at 1AAuto.com, we sell those as well. But then use a 18mm wrench and an 18mm socket and ratchet to tighten up that bolt. And that bolt should be tightened somewhere around 70 to 75 foot-pounds. Put the bracket that holds your brake hose back into place, and start the 10mm bolt on and tighten it up.
Reinstall the wheel. Put the lug nuts on by hand first just to make sure you don't cross thread them, then tighten them preliminarily. Put the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now, reinstall your hubcap and we're going to do that with that 19mm socket. I'm just going to screw them in by hand. Also, we want to make sure you line up the valve stem with the notch in the hubcap for the valve stem. I'll go ahead and fast-forward through that.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends. Before we get started, the first thing that I want to mention is you want to be safe. So, have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So, come right underneath here. This is where you're going to support the vehicle in the front. Now, with the front of the vehicle safely raised and supported, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel.
First, what I like to do is remove the sway bar link from the front strut. So, I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Okay. Now that we have the sway bar link off of here, we need to go over to the other side of the vehicle and remove the sway bar link from the strut as well. That way there, we can move the sway bar up and down as needed to get to that mounting nut. There it is, friends.
Okay, friends. Now it's going to be time to put it in our brand new front sway bar link. One thing I like to mention is it's always a great idea to do these as a pair. And if that's the case, now's the time to do it. So, let's go ahead and put this in starting with the bottom. Now, I'm going to use my 17-millimeter wrench to hold the stud from spinning, and then we'll snug it up. If you were to try to torque this you'd want to torque it to 48 foot-pounds. It's going to be very difficult to torque because as you try to twist, it's going to want to lift up on the bar. If you try to put the bar inside here, obviously, you're not gonna be able to get to it. So, 48 foot-pounds, if you can do it. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm John from 1A Auto. I hope this how-to video helps you out and the next time you need a car for your vehicle, think of the 1AAuto.com. Thanks.
In this video we're going to show you how to replace front struts on this 2007 Pontiac G6. Very much the same for any 2005-2010 G6 as well as the Saturn Aura. We're going to show you the right hand side. The left hand side is the same procedure and we always recommend that you replace your struts in pairs. And speaking of struts you want to get a nice new set of loaded struts from 1AAuto.com. We sell both brand name as well as private label: Jack and Jack stands, 10, 18, and 19 mm sockets, ratchet and breaker bar or pipe for some extra leverage, and 18 mm wrench and a hammer.
Start out by using just the socket to loosen the lug nut covers or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools just start with the vehicle on the ground, loosen the lug nuts then raise and secure the vehicle and remove the lug nuts, wheel, and tire and grab the suspension and turn the wheels or turn them with the steering wheel and there's a 10 mm bolt that holds the brake line bracket to the strut, remove that.
There are 2, 18 mm nuts on the back side of the strut. You want to use a ratchet, using a breaker bar and a pipe or something here for some extra leverage might be in order but you can see on our vehicle they come off with just a good amount of force. Use an 18 mm wrench to grab onto the nuts part of the stud of the stabilizer link and then use an 18 mm socket. Loosen up the nut and then it comes off. Use a hammer, be careful not to damage the bolts too much. You might want to put a nut on the back of them and although ours came out pretty easy, and just drive those bolts right out. Heading up top underneath the hood, there are three 13 mm bolts that hold the top of the strut in place and we'll fast forward as we remove those. You can remove 2 of them and then just loosen one up most of the way.
And as you're taking that last nut off, you can just keep your hand on the strut and as you take the nut off you will be able to lower the strut out. And then put the strut back in place and yes, you probably will notice that we're just putting the old strut back in. The struts in this car were in fine shape and so we're not usually ones to waste putting a new strut into a car that doesn't need them. We're just kind of doing this to show you how to do it but you put it into place, start one of the nuts on top and then start the other two and you can tighten those up and the top nuts you should torque to 20 to 25 foot pounds.
Back down under now, lift your brake hub assembly and steering knuckle back in to the strut. You can force it in there and you put one of the bolts in, and just kind of put it in a little bit and then as you move the knuckle around on the strut you should be able to get the bolt through. Then make sure you put the bracket back into place and you can get the second bolt through and if you like use a hammer or something just to drive the bolts all the way through. And it should be noted that we do recommend an alignment after you do this because the movement of these struts is something that affects the caster and camber of your wheels.
And torque those nuts to 85 foot pounds. Bring the sway bar link back into place and should you possibly feel the need to replace those sway bar links, 1AAuto.com, we sell those as well but then use a 18 mm wrench and an 18 mm socket and ratchet to tighten up that bolt. That bolt should be tightened somewhere around 70 to 75 foot pounds. Put the bracket that holds your brake hose back into place and start the 10 mm bolt on and tighten it up. Please install the wheel and put the lug nuts on by hand first just to make sure you don't cross thread them then tighten them preliminarily.
the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now reinstall your hubcap and I'm going to do that with that 19 mm socket and then I'm just going to screw them in by hand. Also want to make sure that you line up the valve stem with the notch in the hubcap for the valve stem and I'll go ahead and fast forward through that.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free: 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
Okay, friends. The first thing you need to talk about anytime you're working on your vehicle is safety. You want hand and eye protection. With that said safely raise and support your vehicle so the wheels are off the ground. Once you've done that, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel.
Once you have the wheel off, it's important to remember that we're actually going to want to try to raise this up a little bit. We want to take the pressure off of your shock so it's not fully extended. If you were to try to take out this bolt right now, once you finally got it to almost the end, the suspension is going to want to drop and you might damage the threads inside of your knuckle. And now, we're gonna remove this bolt right here using a 21-millimeter socket. Next, we need to remove our two upper mounting nuts. Just remember when you remove these, there's going to be nothing holding your shock up. So, after you remove one, make sure you have full grasp on it. Go ahead and remove this from the vehicle. Next, we're going to remove this upper nut to get off the upper mounting from the shock. Every time I get shocks, I always like to charge them up before I install them. What I mean by that is to go ahead and press this down as far as it can go, let it completely come all the way up, and then repeat the process three to five times. Let's take our new shock. Take the nut off of there, and we'll remove both of these. Now, let's get our pieces on. We're going to put it just like this. Now, let's grab this piece, slide that right over. Put this facing in like that. And this right here. All right. Let's tighten this. Perfect.
Let's get ready for our install. You'll notice if you put this on backwards because the shock won't be at the right angle. Put on both those nuts, if you want to use a little thread locker, we'll call it your prerogative. We'll snug these up. Torque them to 18 foot-pounds. All right. Let's get our shock lined up here. Take your bolt, slide it through. Take your washer. Make sure you don't forget to put that in there. It's easy to forget. That on there. Okay. Now you might need to lift up or down on the shock to try to get it to line up. Now, let's torque this to 133 foot-pounds. Get our jack out of here. Wheel up on here. We'll start on the lug nuts and then we'll torque them down to 100 foot-pounds. Let's torque these to 100 foot-pounds in a criss-cross manner. Torqued.
Tools used
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a stabilizer link on this Chevy Cobalt, pretty much the same for any Cobalt as well as the Pontiac G5. The stabilizer link makes kind of a rattling or thunking noise when you go over a bump. A good indicator that it's your stabilizer link is if you're getting that rattling noise and then, you turn your vehicle, you take a curve, and the rattling noise goes away; that usually means it's a pretty good indicator that it's that stabilizer link that's bad. The tools you'll need are jack and jack stands, 18mm and 19mm sockets with a ratchet. You'll need some pipe for some extra leverage as well as a breaker bar and 15mm and 18mm wrenches. It's pretty much a bolt-on, bolt-off, but sometimes these nuts are really difficult to remove, so there's some techniques in this video that will help you out.
Use a 19mm socket or lug wrench and remove the lug caps and the wheel cover. If you don't have access to air tools, you'll want to start with the vehicle on the ground. Loosen the lug nuts first and then raise the vehicle and remove the lug nuts and the wheel and tire.
Now, use an 18mm wrench and you can grab on the back side there and then use an 18mm socket and ratchet and remove that nut. Use a little bit of penetrating oil just to help get that nut off easier. Now, I'm using my 18mm socket with the ratchet and a piece of pipe. You can use pipe or if you have a breaker bar. You just need some extra leverage. Get that bolt to move some, and then, actually, grab on to the wrench, hold the wrench, and start it loosened and then you can do it by hand the rest of the way. Once you remove that nut, then you can just knock out or remove the top of that stabilizer link. Now, here what I've done is I've supported the bottom of the suspension. What that allows, is it allows me to get a breaker bar onto that bottom bolt and first you can pull the breaker bar, which breaks the nut and the bolt, breaks it free. Then you see with the breaker bar, I start loosening up that nut. You're just going to have to work at it, it's kind of tough to get apart. Just go at it for a while and the nut eventually comes off. Actually, after you get it loosened somewhat, you can get your ratchet on there, and then, use the ratchet to get the nut the rest of the way off. Once you have that off, you can just reach up in there and pull the stabilizer link out.
So, the 1A strut is pretty much the same thing. It has a little different sizes. It's a 19mm nut and a 15mm stud. We'll fast forward through this part. You just take that stabilizer link and put it back into the new strut and put the nut on, and tighten the nut up. You want to get it nice and tight. If you were to torque it, I guess it would be probably about 45 to 50 foot-pounds. Also, if you have ABS brakes, you want to reconnect any clips or anything that holds the wiring to the strut.
Reinstall the tire. You want to put the lug nuts on by hand first and then just kind of preliminarily tighten them, and torque them when the vehicle is back down on the ground.
We'll tighten and torque these to 20 foot-pounds. We'll speed up here as I do that. On the inside one you can't really get a torque wrench on it, so I just used a small combination wrench and got it nice and tight. 20 foot-pounds is not that tight. You don't want to over-tighten them because you could strip them and these are not bolts that you want to strip. Now torque your lug nuts to 100 foot pounds each and then replace either your wheel cover or the wheel caps and the retainers
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Steering & Suspension Kits