Replaces
Frequently bought together
Part Details
TRQ fully loaded shocks and struts are manufactured using premium raw materials and calibrated to restore original ride comfort. TRQ shocks are fully loaded featuring a pre-loaded bearing plate, upper and lower spring isolator, upper spring seat, coil spring, boot kit, and premium strut. TRQ recommends replacing your shocks or struts in pairs to ensure even wear of components and improved ride comfort. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our direct fit gas-charged shock absorbers help restore your vehicle's handling and ride quality to just like new.
Replacing struts used to require specialized tools to compress, remove, and transfer the old spring and mount. Our Pre-assembled, complete strut & spring assemblies come with all new parts and make the job much quicker and easier for the do-it-yourself mechanic.
Strut & spring assembly contains:
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to show you how to replace a front strut with an unloaded strut from 1AAuto.com on this 2010 Buick Enclave. We show you on the passenger side, but the driver's side is the same procedure. The items you'll need is that new unloaded strut from 1AAuto.com, flat blade screwdriver, 8mm, 15mm, 18mm, 21mm, 22mm, and 24mm socket and ratchet, 18mm wrench, torque wrench, spring compressors, a 13/16 spark plug socket, and jack and jack stands.
Start off by prying off your hub cap and then remove these 22mm lug nuts. You want to just loosen them while the vehicle is on the ground and then raise the vehicle up and remove them the rest of the way. Now the wheel will pull free.
Pry up the cap at the end of your wiper arm and then remove this 15mm nut. Then either using a wiper arm puller or just pushing it in and out and using penetrating oil and pulling it off, you want to remove the wiper arm, but a wiper puller helps. You just twist it. It pops it off the stud and you can pull it free. Then you just want to repeat the process on the other wiper arm.
Now you need to remove these four clips, and you can either use a pick and you just pry up the center of the clip and then pull the clip up and out, or you can use a flat blade screw driver, pry up the center, and then pry out the bottom. Remove this ground and pull it free. Then pry out this clip right here, and there's another one on the other side. You just need to pry them out of the body of the car, peel off this adhesive pad from the cowl panel, and do the same thing on the other side. Then pry up this clip right here on the driver's side of the cowl panel, and then pull up sharply on the cowl panel and it will release the clips. Then do the same thing for the other side. Then you want to just pull this up. Make sure all the clips have released and then pull the panel free.
Now you want to remove two of these three 15mm nuts, and then the last nut you just want to loosen most of the way. Use a flat blade screwdriver and pry out the clip that holds your brake line in place. Then an 18mm socket and ratchet you just want to get the bolt on the end of the stabilizer link to move. You have it moving. Then use an 18mm wrench and then an 8mm socket and ratchet. The 8mm socket and ratchet hold the stud into place while you remove them with the wrench.
You might have to a couple of times, spray some penetrating oil on, re-tighten the nut, and then loosen it back up. You can see, it just pulls right out. Now remove these two 24mm nuts, and you can loosen them up with a breaker bar, or you can use power tools. Once you get those nuts to a certain point, just put them back on just a little bit, and then pull this harness out of here. Just make sure you put the nuts on so they're flush with the bolts. Once you get them moving, then take the nuts off. All right, we've got the jack supporting the suspension just a little bit, so this comes up nice and loose. You want to make sure that your steering knuckle doesn't pull too far out. Remove the nut. Now we just wire tighten this right here so there's not too much stress on the axle or too much stress on the hose here.
Now with the strut out, you have to compress the spring. I've got my spring compressors. I'm just going to tighten those up. This is a large spark plug socket and it's got an insert in here to hold the spark plug up. I'm just going to take a 90-degree pick and pull that insert out so it's wide open. Put a 7/8 wrench on here and then there's a 9mm socket and I have an adapter on it to get it to 3/8. This socket is on here really tight, so I want to knock it off first.
Now you can just remove that nut and pull the top off with the spring and this pad. Take your new strut. Just loosen up the nut on the top and it will just pull out. Take this boot, transfer it over and transfer over this pad. Once you have that lined up, take the spring and lower it into place. Then the same way you got the previous nut off, you want to do that again to tighten this one back on. We'll fast-forward as Mike does that.
Before I tighten it up, I've just got my spring there, which it's in my cushion correctly. Make sure it's right there on the platform of the strut as well where it's supposed to be. Then, just to preliminarily aim, this should be facing towards the outside of the car, and then this stud here, the big one, should be towards the outboard part of the car. Once you line it up, tighten up the nut that holds the spring out of the strut, and then make sure it stays lined up as you loosen up your spring compressors.
Now feed the strut back up into place. You just want to push those studs through, replace one of the nuts preliminarily to just hold it there, and then line up the wheel knuckle into the strut. Then replace one of those bolts just to help hold it into place. Then replace the other bolt, and you can just hammer them in the rest of the way. Now just replace those two nuts. You can adjust your alignment, so you will need to have your vehicle aligned after you install these.
It looks like mine is pretty close to the middle. The top one is fixed, but the bottom one you can flex by pushing in or out on the knuckle. I'm actually just looking in behind. I can see a nice line where my old one was sitting. I'm just going to line it up there and then tighten it up preliminarily. I'm going to torque these to 120 foot-pounds.
Jack the strut up into place. I'm just going to put these 15mm nuts back on. I'll preliminarily tighten them, but we're going to torque them once the vehicle is back on the ground with the wheel on. Take the harness clip from your old strut and it just pulls out. Then you just push it into place in the new strut. Then re-clip the harness into that clip. Push this clip back into the lower part of the strut. Push the sway bar link back into place, and then just replace that nut and tighten it up.
Now you can replace the wheel, and then just replace the lug nuts and tighten them preliminarily in a crossing pattern. Then you want to lower the vehicle and tighten these the rest of the way and torque each of them to 100 foot-pounds, again in a crossing pattern.
Then you can just line up and hit your hub cap back into place. Now torque these three nuts up here to 45 foot-pounds. Pull out any clips that stayed behind in the vehicle and push them back into place in your cowl panel. Then feed the cowl panel back into place. Make sure it tucks back under, under the hood. Once you get everything lined up, just start pushing the clips back into place. Make sure that this adhesive cushion over here goes back up and over, and repeat the process on the other side.
Now replace those four clips. Just push in the lower part and then the center to lock them in. Replace the ground and tighten it back up. Make sure your weather strip is back in place, and then, for now, you can close the hood. Make sure these clips on either side of the cowl panel are back into the body of the vehicle. Push the wiper arm onto the stud. Make sure it's lined up where you want it and then replace that 15mm nut and tighten it up. Put the cover back on the end. Now just repeat the process with the other wiper arm.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Remove the wheel, I'm gonna use a 22-millimeter socket. Take the wheel off. So I want to support the lower control arm. I am going to use a screw jack just to take the tension off the shock. You can use a floor jack or even a jack stand. Now I can use a 13/16-inch wrench or a 21-millimeter wrench, put it on the nut right here, and then a 21-millimeter socket, take this bolt out, and this bolt. All right. So that's separated down there. Now, before I take this bolt out here, I'm just going to loosen up these two bolts for this bracket. I don't have to take the bolts out completely, just loosen them. Use a 15-millimeter socket. That's good. Now I'll take that bolt out. Then take a 15-millimeter socket and an 18-millimeter wrench and loosen this up. Take that bolt out. You can slide that bolt out, watch the brake hose. I'm going to slide that out. And to loosen that bracket up, that just makes sliding this out and the new one back in a lot easier.
Before we install the shock, you just want to exercise the shock, just compress it and let it expand. It's going to get the fluid to go through the system and do its thing properly and then it'll be all set to put in the vehicle. And take the shock and the bolt, slide it in position, watch out for that brake hose. Just like that and get this started up here. And before I tighten that all up, let's put the lower bolt in. Now, there is this washer that is domed up a little bit, now that's going to go right in this position here on the control arm. And you can take the bolt, slide it through. If you have to move the control arm up a little bit, you can move it up. And take the washer and the nut, get that started. Now we'll tighten this and torque this to 52 foot-pounds. I'll just snug these two bolts up. Now I can lower the screw jack. Now put the tire back on. Now we'll torque these lug nuts to 140 foot-pounds in a star pattern, that way it tightens the wheel down evenly. And I'll just go around again, double-check.
Tools used
I'm going to remove the wheel. Use a 22-millimeter socket, and then pull the wheel off. I'm just going to use a little rust penetrant. There's a little bit of rust on the stud. Take this wire off right here. There's a little retainer there. You might need a pry tool to get that off. And then there's one on the side here. Take an 18-millimeter wrench, and you can loosen up the nut, and the stud is going to spin, so you want to use an 8-millimeter socket. Put it on the stud. You can try to loosen this up with an impact, but the stud is just going to spin. And take the nut off, then you can take the stud out, just like that. Take these two nuts off. Use a 24-millimeter socket. Now, we're going to take these bolts out. Just use a hammer and give it a tap. There we go. Do the same for the other one. There we go. Right. So that I don't put too much tension on the brake hose itself, I'm going to take this bracket off. Just use a 10-millimeter socket. Take this bolt out. And you don't want to bend this hose too much, but that'll give you a little slack. Then we can slide the knuckle out. Now, I've got to take the wiper arms off. I'm going to use a straight blade screwdriver. Just get underneath the clip right here. Take that nut off. Use a 15-millimeter socket. Take that off, and just grab the arm. Just rock it back and forth, slide it off. And you're going to do the same with the other arm.
Take this fuse box cover off. Just use a straight blade screwdriver. Just push on the locks and slide them up out of the way, and then take this ground connection off. Just use a 15-millimeter wrench, loosen it up. And there's push clips along the front of the cowl. There should be a couple more on that side. Those are missing. Just use a straight blade screwdriver or a trim tool. Get underneath the clip and just slide those out. And then you're going to grab the cowl and just slide it over the stud right here, and then just try to raise up underneath. There's push pins holding it on. You can try to get underneath there with a trim tool, but normally, you can just pull it straight up, and then you can just pull it back there, and you can just raise it up out of the way. You don't necessarily have to take it out any further than that. I'm just going to put a little prop rod here. Just use a screwdriver or a trim tool. That works. And there's three nuts on the top. Just use a 15-millimeter socket. Take those off. When you get to the last one, you're going to have to support the strut underneath. All right. Now, I'm going to support from underneath. Get the last nut off and slide it down. Take these nuts off. Just keep one in your hand, then slide it in position. Then get the nuts started and then you can get the other ones started.
Now, we're just going to leave these on like this. We'll leave those loose. It's going to be easier to install it from down below, and then we'll tighten these up last. Then I'll take the knuckle and just line it up. You're going to have to pull it up a little bit and try to line the bolt up. There you go. Get the other one in. Just give it a little tap. You don't have to hammer it in all the way. And take the nuts. Get those started, and then we can tighten these down. Then we can torque these nuts to 144 foot-pounds. All right. Now, take the sway bar link and line it up. Get the nut on, and I'll use an 18-millimeter wrench to hold the stud, 18-millimeter socket. Tighten this up. Now, I'll torque this to 59 foot-pounds.
Now, the ABS wire, slide this in position right there and right there. Now, just take this brake hose bracket. Line this back up. Put this bolt on. If you felt uncomfortable taking this line off or this bracket off, you could always take the caliper off and hang the caliper on the strap assembly, and tighten this bolt down. Put the tire on. Now, I'm going to torque these lug nuts to 140 foot-pounds in a cross pattern or a star pattern to tighten the wheel down evenly. Now, I'll go around again. Just double-check. Now, we can tighten these down. Torque these nuts to 33 foot-pounds. All right. Now, I can take this cowl, and if any of these push pins came out down below, transfer them over and slide this back in position, and just line it up. And that looks good. You can take some of these push pins and then reinstall these. It should be four of them. And take that fuse box cover, put it back on. Now, I can reinstall the ground jumpstarting terminal, get that started, and just snug it up. That's good. Now, take the wiper arms and line them up. Try to put them back where they were. If you had to, you could mark them before you took them off, and put the nuts on. While holding the arm, tighten the nut down, snug it down, then put the cover on. Do the same for the other one.
Tools used
