Chevrolet GMC Cadillac Driver & Passenger Side Windshield Wiper Transmission Arm 2 Piece Set TRQ WWA06899

Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.

In this video, we're going to be working with our 1996 GMC Sierra K1500. We're going to show you how to remove and replace your vehicle's wiper transmission. This is actually two individual pieces in this vehicle, one for the passenger side and one for the driver's. We're going be to replacing the passenger side, but the process will be the same for the driver's. If you like this video, please click "subscribe." We have a ton more information on this truck as well as many other makes and models, and if you need these parts for your vehicle, you can follow the link down in the description over to 1AAuto.com. Here are the items you'll need for this repair.

Use some small pieces of painters tape to make a straight line with your wiper blade. This will help us position the arms back on without needing to do trial and error. Using the flat blade screwdriver, pry out on the tab on the top edge of the wiper arm at the pivot. Remove the wiper arm from the pivot. Do the same thing on the opposite side.

Remove the weather strip from the top of the firewall. Remove the three Phillips-head screws securing the cowl to the truck on both sides. There's one down on this opening. There are three, both in the same positions on either side of the vehicle. Once you get the first three screws removed, lift up and remove this corner panel that goes around the hinge. There's a fourth Phillips-head screw under there you'll also need to remove. Remove the three screws from each corner of your cowl.

Once that's done, you can remove all four of the Phillips-head screws along the front of the cowl. Pull back and lift up to remove the cowl. You'll need to disconnect the washer hose over here on the driver's side. Remove the cowl from the vehicle.

Loosen the 10 millimeter nuts on the wiper linkage. There's no need to remove these entirely. If you're doing the driver’s side arm, you can stop here and move on to removing the other portion on the other end of the arm. However, for the passenger side, you'll need to loosen this.

Remove the three 11 millimeter bolts securing the pivot end of the wiper transmission to the truck. Lower the pivot into the cowl. Slide it up and out of the next opening.

Send the arm back into the truck. Line up the pivot and the three holes and reinstall your three 11 millimeter screws.

Snap the arms back on to the wiper, tighten them back down with your 10 millimeter socket and ratchet. Make sure they're in the same place they were removed from.

Reconnect your windshield washer hose, and lay the cowl back into place. Reinstall the four screws in the center section of the cowl. Reinstall the two short screws on the end. Once the rear one's in, you can reinstall the plastic cover. It simply slides in and drops down. Reinstall the longer screw on the outer edge here. Repeat these steps on the opposite side. Reinstall the weather strip onto the top edge of the cowl.

Now, I know we had mentioned using the painters tape to align these earlier, but it turns out these wipers are keyed, which means they'll only go on one way. Simply pull out the tab and slide them back on. Lock the tab back into place. Lay the wiper down. Remove the tape.

Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the passenger's side wiper linkage on this 1996 Chevy Tahoe. The items you'll need for this include a new passenger side wiper linkage from 1AAuto.com, Phillips screwdriver, a flat blade screwdriver, and a 10mm and 11mm socket and ratchet.

First, using a flat blade screwdriver, just pry up this clip, pull the wiper arm up and off, and do the same for the other wiper arm. Next, you want to remove this Phillips screw from either side of your vehicle. Then this panel just pulls off, and repeat the process on the other side. Then remove this Phillips screw and the Phillips screw on the same spot on the other side. We'll just fast-forward as Don does this.

Now pull off your weather strip and remove these six additional Phillips screws. We'll fast-forward while Don does this. Now pull the cowl up and forward, and now you just want to pull your washer hose off and slide the cowl out. Next, loosen up these four 10mm nuts. We'll fast-forward as Don does this. Now pull both of the linkages from the wiper motor stud and then remove these three 11mm bolts around the passenger's side linkage post. Now pull the wiper linkage out.

On the right is the old wiper linkage; on the left is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Remove one of the 10mm nuts, loosen up the other one on your new wiper linkage, and then feed it back down into place. Then push the linkage onto the wiper motor stud, pull the post up through, and replace those three 11mm bolts.

Then tighten the 10mm nuts, push your other wiper linkage on, and make sure you have it lined up in the center. Then tighten those two 10mm nuts. Now, put your cowl panel back into place and reconnect the washer hose.

Then line it up and replace those two Phillips screws on either side of the cowl panel. Then replace the six screws in the center of the cowl panel. Now replace those two side panels and the Phillips screw that holds them into place. Push the weather strip back on. Then close your hood.

You want to line up that line with the slot, push the arm back onto the post, push the tab in, put the arm down, and then repeat the process for the other arm. Then you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the driver's side wiper linkage on this 1996 Chevy Tahoe. The items you'll need for this is a new driver's side wiper linkage from 1AAuto.com, a Phillips screwdriver, a flat blade screwdriver, a 10mm and 11mm socket and ratchet.

First, using a flat blade screwdriver, just pry up this clip, pull the wiper arm up and off. Do the same for the other wiper arm.

Next, you want to remove this Phillips screw from either side of your vehicle. Then this panel just pulls off, and repeat the process on the other side. Then remove this Phillips screw and the Phillips screw on the same spot on the other side. We'll just fast-forward as Don does this. Now pull off your weather strip and remove these six additional Phillips screws. We'll fast-forward while Don does this. Now pull the cowl up and forward, and now you just want to pull your washer hose off and slide the cowl out.

Next, loosen up these two 10mm nuts. Once you've done that, you can push it right off that stud. Then remove these three 11mm bolts. Now we'll just fast-forward as Don does that. Now you can pull your driver's side linkage up and out.

In the back, is the old wiper linkage; up front is the new driver's side wiper linkage from 1AAuto.com. You can see they're identical, and they're going to fit exactly the same. Now loosen up the two 10mm nuts on your driver's side wiper linkage. Feed it back into place.

Pull the linkage post up into place, and push the other end onto the wiper motor stud. Then replace those three 11mm bolts. Now tighten up those three bolts. Then the two 10mm nuts, you can actually adjust the linkage a little bit. If you want at this point, you could put the wiper blade back on, adjust it so it parks correctly, and then tighten those nuts up.

Now, put your cowl panel back into place and reconnect the washer hose. Then line it up and replace those two Phillips screws on either side of the cowl panel. Then replace the six screws in the center of the cowl panel. Now replace those two side panels and the Phillips screw that holds them into place. Push the weather strip back on. Then close your hood.

You want to line up that line with the slot, push the arm back onto the post, push the tab in, put the arm down, and then repeat the process for the other arm. Then you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.