WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Interior Front Door Handle 2001-06 Chrysler Sebring
Created on:
Tools used
Flat Blade Screwdriver
T20 Driver
Phillips Head Screwdriver
1. Remove the anchor points
Pry up the plastic plugs behind the door latch and door pull.
Remove the six Phillips screws, two under the plastic covers you removed and four around the edge of the door panel.
2. Unclip the door panel
Pry up the corner panel piece located by the side mirror.
Use your flat blade screwdriver and a rag if needed (to protect your paint) to work the door panel off.
Unclasp the door lock rod.
Disconnect the wiring harness.
3. Remove the door handle
Remove the two T20 bolts securing the handle on the inside of the door panel.
Pry out the clips on the switch.
4. install the new door handle
Clip the switch into the new door handle.
Bolt in with T20 Torx bolts.
5. Re-install the door panel
Clip the door handle/lock rod back into place.
Reconnect the wiring harness.
Fit the door panel back onto the door and click the clips back into a secure, locked position.
Screw in the Phillips screws and replace the plastic plugs behind the door pull and latch.
This Video is brought to you by: 1A Auto. Hi, I'm Don from 1A Auto. I hope this how to video helps you out, and the next time you need a part for your vehicle think of 1AAuto.com. Thanks.
In this video, we show you how to replace the interior door handle on this 2004 Chrysler Sebring, and the only tools you're going to need for this is a flat blade screwdriver, a Phillips screwdriver, and a T-20 torques bit. There are two trap doors here. There's one right here behind the door handle, and another one here in the pull cup. All you want to do is take a flat blade screwdriver and stick it into the slot on the side of them and just pry them out. Now what you want to do is remove each of these Phillips screws. There are six in total, and we'll just fast-forward as Don removes those.
Take your flat blade screwdriver and pry off that triangle panel. To release the clips on the back of the door panel, you just want to pull out all the way around the door panel. Once you've done that you can lift it up and off of your door lock knob. Then behind the back of the door panel you'll see here's your door handle rod. You just want to pop that clip up, and pull that up and out, and you want to disconnect the two harnesses here by just pushing in the tab and pulling them out. Now your door panel is free.
Now from the back side of your door panel, you'll see there's two T-20 bolts right here. You just want to go ahead and remove those. You want to just, using a flat blade screwdriver just pry out the clips on either side of your switch here. Then just pull that switch out. Now you take your switch and just push it into your new door handle, and put the door handle into place. Then you just want to replace those two T-20 torques bolts.
We'll just fast-forward as Don replaces those. To reinstall the door panel, you just want to take that door handle rod and put it back into place and re-clip it. Then you just want to reconnect your two harnesses. Once you've done that, you just want to line up your door. Put it up and over the door lock knob and down into place. And, then you just want to push those clips in around the edges of the door panel. We'll just fast-forward here as Don replaces those six Phillip screws. Now just replace your trap doors and that triangular panel.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts, and the best service on the internet. Please feel free to call us toll free at 888-844-3393. We're the company that's here for you on the internet and in person.
DHA49827
In Stock
Product Reviews
Loading reviews
5.00/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
Awesome
TED
December 23, 2017
The utube video was a tremendous help. Easy ordering parts and delivered in a timely fashion. Thanks.
Great price
K
April 4, 2019
Work great great price
Worked great.
W
July 28, 2019
The handle worked great, and the price was well below my alternatives. I only needed the handle, but no big deal. For the price, it was well worth it. I had to drill out the hinge pin hole a bit to fit my '01 Sebring convertible's existing hinge pin, but that didn't take long and the handle fit right into place. Two weeks now and no issues. Definitely recommend.
Great product, great service
Dudley
June 6, 2023
Very happy with the product. The installation video made it very easy to install.
Customer Q&A
WILL this Interior Door Handle Driver Side fit my 2002 Chrysler Sebring Limited Convertible?April 1, 2019
Robert-V. M
10
This part is only able to fit for sedan models.
April 1, 2019
Emma F
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chrysler is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Chrysler or FCA US LLC.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.