2006 Chrysler Pacifica Rear Driver & Passenger Side 2 Piece Power Power Window Motor & Regulator Assembly Set TRQ WRA50579

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to place a rear power window regulator on this Chrysler Pacifica. We'll show the driver's side. The passenger's side is the same procedure. Tools you'll need are a Phillips screwdriver, a door panel clip tool (or a household putty knife would work in its place), two 1/8th flat blade screwdrivers. Those are the smaller screwdrivers, a 10mm wrench or a socket and ratchet, painter's tape and a flashlight.

First carefully use your screwdriver and, if you go from the back, push it forward, pop it out, or you can come from the front and pop that out there. That comes off. Do the same thing right down here with screwdriver. Pull it out and then there's Phillips screws right in behind. Then just fast forward as I remove those two Phillips screws.

Start here in the front and we'll work your door panel clip tool right in behind, until you come to a clip. Pull it firmly and take off. There are three connections and the harness down here. Just press up on the tab and that disconnects. For this cable pull it out, then down. Then there's a little clip here that you undo and move that. This pulls right up out and you pull it up and slide it forward and bring it out.

Next you'll access the inside of the door. Remove a couple brackets: one at the top and one in the middle. They're just held on by Phillips screws. Remove your speaker. Again, it's held on by three Phillips screws. Unplug it and then carefully pull down your water shield, taking care not to rip it and pull it away from the vehicle.

You can see right here there's a cable and this is a cable actuated regulator. A lot of times this cable breaks. What you need to do is disconnect your lead for your motor. Just push out on this red safety tab. Push that that way and reach in, push down on this tab. Disconnect it.

Then you need to separate the window from the regulator. I've got my window in my down position. You can see my regulator's actually in good shape. I'm just doing this video to kind of show you, but right here is where the window attaches to the regulator. I'm sure Chrysler has some kind of special tool for this, but I'm taking a small screwdriver. Give a little perspective here. There's a small screwdriver. I'm going to slide it right in behind here. Now, you can see I've got that screwdriver in there. Then this screwdriver is positioned on the other side, prying this tab out. Now I have to with those screwdrivers, you've got to make sure the outside screwdriver is way down in. Then I'm actually pushing the screwdriver out towards the door and lifting up with this hand on the window, as well as prying out this hand. Then, I finally get the window to unlock.

Pull the window up. So I've pulled my window up, secured it with some painter's tape and now there are three bolts: one here, one here and then one down here. Just use a 10mm socket with a ratchet and extension to loosen this top one. Loosen this one and then we'll actually remove this one. We can now lift the regulator up and bring it out.

As you can see, my original one is in fine shape, so I'm going to reinstall it. A new one from 1A Auto will all mount the same. The only difference is they may have a pigtail here which is not a big deal. They still connect the same way. You'll want to put these two bolts into your new regulator and just feed it into the door. Bring it right up. Make sure you kick the bottom out and then get it right down in. It drops right down in. Start this bolt down here. I'll just speed it up here as I finish putting that bolt in. Remember to tighten up the three mounting bolts that hold the regulator to the door. Reconnect the harness and lock the safety tab on.

I'm just going to undo my tape up here. Let my window fall down, not fall down, but let my window come down. You can just kind of look right in here. It should go right into the regulator. It snaps in. You're regulator is all installed.

Now we're just going to put the water shield back on, the speaker and the door panel. I'll speed up here as I put the water shield back on. Make sure as you're putting it back on, you pull the wires and the cables through as well as just lining it up correctly. Make sure it doesn't block any of the holes where the clips and pins go into the door panel. Then once you do that reinstall the speaker. Remember to plug it in obviously and then reinstall the two door panel mounting brackets, the one in the middle and the one up in the top corner.

Reinstall the door panel. Bring this close, plug it in. On these cables, this one has kind of a T end. Put it in. Just kind of slide it back in. It's kind of hard to do. Then clip it in there. This one put it in. Bring the clip around. Pull the cable back and slide it in there. I'll bring my door panel up. Make sure the top of it goes right down in. Kind of peek around the back here and slide back some. My clips go in and connects to the front here. Make sure all the clips are going in. Fast forward again as I just reinstall those two Phillips screws: one behind the door handle and one behind the door pull Then put these little trim doors back in place. You have kind of a longer tab that goes into the wider slot. Push the longer tab in first.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.