Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace Tail Light Housing 2005-09 Chevy Equinox
Created on:
Tools used
Flat Blade Screwdriver
Phillips Head Screwdriver
1. Removing the Taillight Assembly
Remove the two plugs to the side of the taillight.
Remove the two Phillips screws.
Pull the light from the top while supporting the bottom to free the taillight assembly.
Disconnect the connector.
2. Replacing a Bulb
Twist the sockets counterclockwise.
To remove large bulbs push the bulb down and twist counterclockwise.
Twist the new bulb into place.
For smaller bulbs pull the bulb straight out and push the new one into place.
Twist the sockets back into place.
3. Replacing the Taillight Assembly
Reinstall any clips that came out with the old light back onto the car.
Reconnect the harness to the taillight.
Line up the taillight and press it into place.
Replace the two Phillips screws.
Replace the plugs.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the tail lights on this 2008 Chevy Equinox, same as any 2005 to 2009. We're going to show you both replacing the whole assembly if you have broken it or just replacing the bulbs if that's all you need to do. Only tools you'll need are a flat blade screwdriver and either a Phillips screwdriver or a 10-mm socket with a ratchet and extension.
With your tailgate open, there are two plugs here. Use this flat blade screwdriver, pry on the bottom. Remove those. Inside, you can see there are two screws. You can either use a 10-mm socket with a ratchet or a Phillips screwdriver.
Once you have those out, this part's a little unnerving but just kind of work your fingers in and constantly pull, kind of support the bottom here. It pops out. The light comes out. There is a connector right here. There's a little tab on the bottom side. Push up on that tab. It's a little stuck together here. Give it a good shake.
That comes apart. You don't have to disconnect it if all you're doing is changing the bulbs. Makes it a little easier, though. All the bulbs twist the sockets counterclockwise. It comes out. These larger bulbs, you push in. Twist counterclockwise. They come out. Put back in, just put in the correct position, turn it clockwise to lock. Smaller bulbs go in counterclockwise. Generally, they just pull right out of the socket. This one's a little stuck here. Twisting. They pull right out. Push back in. All I did was keep shaking it back and forth to get it loose. There's one larger pin on here. Just make sure you line it up correctly. Push it in. Clockwise to lock. Same with these two. This right here needs to go back on the car. Just use the screw driver, right off. Re-install it to the car.
Here's our obviously original light. That's fine. New light from 1A Auto. Obviously, if your light has been broken or whatever. Taillights getting broken is pretty common. The new light from 1A Auto is going to go right in, fits in nicely. First, let's put this on there. Plug it in. Make sure it's tight. Make sure it's on the bracket. You want to put your light in. Make sure that the harness goes in correctly. Push it into place. Peek back in here. Make sure your wires aren't getting in the way. Now, put the pins in place. Make sure everything is set well. Lock it into place. Put our bolts on. These have little tabs at the top. They go to the top. Clip in. Clip in. Then, you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the Internet and in person.
GM384-B000R
In Stock
Product Reviews
Loading reviews
5.00/ 5.03
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
0
awesome product!
J
February 1, 2018
I was amazed to find that not only the bulbs were included but a totally new wiring harness as well!!!! Easy installation and fits like OE part Did! Looks great and matches other tail lights perfectly!!
Perfecto!!
James
February 24, 2018
The item was exact. The wait time was not too long and the product delivered on time.
High quality tail-light
John
May 3, 2018
Great product, perfect fot. High quality product!, that shipped on time.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.