Replaces
Replaces 2014-16 Cadillac SRX Driver & Passenger Side 2 Piece Headlight Set DEPO 1ALHP01464
$637.95
Replaces 2010-16 Cadillac SRX without RPO Code F45 (Real Time Damping Chassis) Front 14 Piece Steering, Suspension, & Drivetrain Kit TRQ PSA35466
$584.95
Replaces Cadillac SRX Saab 9-4X Front & Rear 4 Piece Magnetic Ride Control Complete Strut Assembly & Shock Absorber Kit TRQ SKA33356
$549.95
Replaces 2010-16 Cadillac SRX with RPO Code F45 (Real Time Damping Chassis) Front & Rear 8 Piece Magnetic Ride Control Suspension Kit TRQ PSA37297
$541.95
Replaces 2010-16 Cadillac SRX All Wheel Drive Rear Driveshaft TRQ DSA80150
$490.95
Replaces 2010-16 Cadillac SRX Driver & Passenger Side 2 Piece Performance Headlight Set TRQ Performance HLA95907
$481.95
Replaces 2010-16 Cadillac SRX without RPO Code F45 (Real Time Damping Chassis) Front 12 Piece Steering & Suspension Kit TRQ PSA35464
$473.95
Replaces Cadillac SRX Saab 9-4X Fuel Pump Module Assembly Delphi FG1742
$462.95
Replaces Chevrolet GMC Buick Cadillac 6 Piece Fuel Injector Set Hitachi Automotive HIEEK00008
$406.95
Part Details
Product Features
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
I'm going to open the lift gate, just grab underneath here, push the button, and it will automatically open. We're going to pull this trim piece off right here. We’re going to need to remove this clip. We’re going to use a trim piece tool to remove it. A little spot on the top get underneath here, pry up, and once it's out a little then that comes out completely. And we can grab this trim, bring it straight forward, and it pops right off, some clips in there.
We're going to take these Phillips head screws out: there's two right there, just use a Phillips head screwdriver pull those out. We're going to grab the tail light and grab underneath here the side. Pull it straight back. It might fight you a little bit. These little pieces go into these little slots.
To disconnect the wires, you’re going to push this connector right here down on the lock and pull it out. A little lock right here, push that down, and pull that one out. Then the bottom one the wiring harness is held in by this clip, pull that off, and then right here push this connector down. There’s a lock right at the top. Slide that out.
All right, we're going to remove this reverse light bulb. Just grab it, twist it to the left, and pull it out. This bulb is an HPC 16W. We'll remove this bulb, turn it to the left, and pull it out. You can grab the bulb from the socket and firmly pull it straight out. This bulb is a W21W.
To reinstall, we'll line it up with the slot, lock it in, and we'll reinstall it in the taillight assembly. We're going to line this bigger slot up with this slot right here and then turn it to the right. To install the bulb you're going to line the tabs up right here with the holes, the slot in the assembly, push it all the way down, and turn it to the right, lock it in.
Now we're going to connect the connectors. Take this connector and line it up, push it in, lock it in, and then this retainer that holds the wire, slide that on just like that. Take this green connector, line it up, lock it in, and then this connector will go way up here and lock it in make sure it's in there good.
We're going to line these tabs up with the holes in the body. Get those lined up good, and then firmly push the taillight on. Now we'll install our Phillips head screws with our Phillips head screwdriver. Get that one started and go down here. Start this one and we can snug it down. Not too tight it is in plastic so just snug.
All right we're going to align these little clips up with these holes on this trim piece and then push it on and lock it in. Get it underneath the weatherstripping right there and then we have this little clip, position that and then push it down. Then we'll close the lift gate.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
