Replaces
Part Details
This Ignition Kit comes with NGK G-Power Spark Plugs, TRQ Ignition Coils and TRQ Spark Plug Wires.
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
These are where your spark plugs are on this 2009 Chevy Suburban. It's the rearmost one of the driver's side. We have four in each side. One, two, three, four. We go over to the passenger's side. This one is a little bit trickier to get to. It's in the way, way back. We've got back there, one here, one here, and one here. It'll be just enough room to get it. We're going to show you how to replace one on the driver's side front. This procedure is going to be the same for all of them. It just might take a little more maneuvering to get to the other side.
I'm going to give this a little turn, and then you don't want to pull on the wire. All you've got to do is work it off of the electrode and of the spark plug. It's usually on there pretty tight. I should also mention that you should do this when the engine is cold because we're right next to the exhaust manifold. Just put this to the side. You should do these one at a time.
Spark plug is down here in the head. I'm just going to take some compressed air. Just blow around the spark plug. If you don't have that, it's okay. Just be careful. Maybe take a brush. You just don't want anything falling down into the cylinder when you open up the spark plug hold. These spark plugs are going to take a five-eighths socket. You want to get a spark plug socket. This is a regular five-eighths socket. If you put a spark plug in here, it's real, real loose, and you can turn it while you're trying to install it. The spark plug is going to fall out.
A spark plug specific socket has a rubber insert to grab on to the foursome part of the spark plug so when you put it in here, it seats. You can go to install it. It's not going to fall out and the same when you're using it to remove old spark plugs. You can lift them out of the engine and they won't fall down. We're going to use a three-eighths drive and my five-eighths spark plug socket. It should be on there.
Take my ratchet. You're going to remove it. These are only torqued to eleven foot-pounds, so it shouldn't take much effort to get them out. Once it starts to get loose, you can remove the ratchet. We just use our fingers to spin it out. As you remove it, the spark plug socket is going to hold it in place so if you need to move it around, you're not going to drop it.
So you can see this is our old spark plug and this is our new one from 1AAuto.com. Their threads are the same length. A single electrode. These are going to work great and give you nice performance on your vehicle.
Take our new spark plug and put it into our spark plug socket. Carefully place it into a spark plug opening. Sometimes if you go backwards, it helps you find the threads and then you can spin it forward to go in. It should go in very, very easily. If it feels like it's cross-threading, you should stop and make sure that it's going in nice and straight. Okay. Now that you've got it hand-tight, we're going to torque it to eleven foot-pounds.
The spark plug torque can reinstall our spark plug boot. Just push it on as hard as you can and just check that it's seated.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2002 Chevy Suburban with the 5.3 liter, V8 engine. It's the same part and similar process on these Suburbans from 2000 to 2006. The items you'll need for this are a new ignition coil from 1AAuto.com and a 10mm socket and ratchet with an extension.
Your ignition coils are located right here. There are four on each side since this is a V8 engine. To remove these ignition coils, it's the same process for each of them; they're held in with two 10mm bolts. The only difference is this one right here that has a bracket for these hoses over it and that bracket also just held in with a 10mm bolt. We'll show you on this one since it's a slightly different procedure. Just lift up on the tab and disconnect that harness, and then, using a 10mm socket and ratchet, just remove that 10mm bolt, right there. Now you can just pull that bracket aside, and then, pull your spark plug wire from the ignition coil. Then remove the 10mm bolt at the top and the bottom of the coil. The coil will pull right off.
On the left, is the old ignition coil; on the right, is the new one from 1A Auto. You can see they're identical and they're going to fit exactly the same. Take your new ignition coil and push it down into place and then replace those two 10mm bolts. We'll fast forward as Don does this. Now reconnect your spark plug wire and then push this bracket back into place and replace that 10mm bolt. If you're replacing multiple ignition coils, obviousl,y you just repeat the process for each one and finally just reconnect the harness and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we are going to show you, we're going to show you how to replace a spark plug in this 2002 GMC Sierra 2500 HD. It's pretty much the same process with most V-8 engines. And the only tools you're going to need for this vehicle is 5/8-inch-deep socket or a spark-plug socket and a ratchet, and you're also going to need a gap tool.
Okay, so because this is a V-8 engine, it has eight spark plugs. There's four on this side and four on the other side, and in this video, we are just going to show you how to change one of them, but it is pretty much the same process for all eight. Okay so, using your gap tool, you just want to make the gap on the spark plug the proper size. In this vehicle, it is .06. You just want to use the pegs on this pry out the gap on the spark plug until you get it so that there's just a little bit of resistance as it slides on to the proper size. And there it is.
Okay, so you just want to reach down to the spark plug you're changing and disconnect the spark plug wire, and then using your 5/8-inch-deep socket or a spark-plug socket and a ratchet, you just want to twist that out. And then just remove that spark plug. Okay, and then what you want to do to replace it is just put that spark plug right into the socket, feed it down into the hole and just twist it until it's threaded on there. Once it's threaded, you just want to use your ratchet and tighten up that spark plug the rest of way. Generally, you want to tighten them to about 20 to 25 foot pounds. Then remove your socket and put the spark plug wire in place and just repeat that process for the other seven spark plugs.
We hope this helps you out. Brought to you bywww.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
