Kit Includes: (1) Spark Plug Wire Set (8) Ignition Coils
Ignition Coil Style: Square Style
Product Features
Matched TRQ Kit: Fit, lab, and road tested for peak performance
Application Specific Design: No modifications necessary
Heat Range and Life Cycle Tested: Exact match to stock specifications
Complete repair to restore your engine to like-new conditions
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How To Replace Coils 2000-06 Chevy Tahoe
How to Replace Ignition Coils 2000-06 GMC Yukon
How To Replace Spark Plug Wires 2000-06 Chevy Tahoe
How to Replace Spark Plug Wires 2000-06 GMC Yukon
How to Replace Ignition Coil 2000-06 Chevy Suburban
How to Replace Spark Plug Wires 2000-06 GMC Yukon
Created on:
Tools used
Dielectric Grease
Torque Wrench
Socket Extensions
Socket Driver
8mm Wrench
10mm Socket
Okay, we want to disconnect the battery, disconnect the negative cable using an 18-millimeter ratchet wrench or a wrench. And slide that out of the way. Now on this coil, there's a bracket in the way. So, you can take these hoses. Just slide them out of the way, the heater hoses. You can take this bracket off. Just use a 10-millimeter socket. Take that pin off. Don't drop it, and slide that out of the way. You don't necessarily have to take it out of the way if you can gain access to it, but it makes it a little bit easier.
Now, you can disconnect the spark plug wire. Just slide that off, and there's two bolts. One bolt here, and one bolt up top. Take that bolt off. Take that one off. And then slide this coil out. You can disconnect the connector right there, and slide it off. Take the coil, and line it up, and take the bolts, get the bolts started. Just snug these up. Now, I can take a torque wrench and torque those bolts to 71 inch-pounds. Make sure you're on inch-pounds, not foot-pounds. It's good.
Now, you can hook up the plug wire. Make sure it clicks in place, and hook up the connector. Now for this one, you can put the bracket on. Just line it up. Put that nut on, and tighten this up, and snug it up. You're going to take the heater hoses, put them back in the bracket. And for the other coils, it'll be the same procedure. Now, we can hook up the battery. Line it up, and get it started, and snug it up. Just make sure it's not loose. Looks good.
Tools used
10mm Socket
Ratchet
You can move these heater hoses out of the way. Just pull them out of the bracket and slide them to the side. Then you can access the coils.
You can take this wire off right here. Just twist it back and forth. You should be able to do it with your hand, and just slide it off like that. Disconnect the connector. There's a little tab. Just pull up on the tab, slide it out. Now just take a ten millimeter socket, take this bolt out here and the one right there. Get those bolts out. Grab the coil, just slide it up.
Take the new coil. Set it in position. Put the bolts in. Get those started. Right there and right there. Then I can torque these bolts to 71 inch-pounds. Plug in the coil. Lock it in place. Take the coil wire and slide it on. Then we're gonna do the same procedure for the rest of them.
And move these heater hoses, put them back in the bracket.
Tools used
Dielectric Grease
Hose Pliers
8mm Wrench
All right. We want to disconnect the battery. Disconnect the negative cable, use an 8-millimeter ratchet wrench or a wrench, and slide that out of the way. All right. Now, replace the plug wire. Just grab the top of the wire, pull it down. And then, at the spark plug, you can try twisting this first. See if you can loosen it up. Try to pull it. Try not to bend the aluminum too much, but if you're struggling to get it off, you might have to a little bit. There you go. Pulled that one out.
You can take a little dielectric grease or some silicone lubricant. Just put this in the end right here. Then, you want to take the heat shield off the old wire and reuse this. Now, we can line this up, up top on the coil. And then line it up with the plug. Slide it in position. Make sure it clicks in place, just like that. Then you're going to do the same procedure for the other wires.
Now, we can hook up the battery. Line it up, get it started, and snug it up. Just make sure it's not loose. That's good.
Tools used
Dielectric Grease
You can move these heater hoses out of the way, just pull them out of the bracket and slide them to the side. Disconnect the wire at the plug. You can give it a twist and pull it off. Disconnect the wire at the coil, do the same. Twist it. Slide it right off.
Take the new one. This new one has a little bit of dielectric grease in it. But if it doesn't, you can always add some. Slide the part on into the coil, lock it in place. And then put the other part for the spark plug and lock it down. And you can do the same with the other ones. And move these heater hoses, put them back in the bracket.
Tools used
Socket Extensions
10mm Socket
Ratchet
1. Removing the Ignition Coil
Disconnect the ignition coil wiring harness
Remove the 10mm bolt from the hose bracket
Pull off the hose bracket
Disconnect the spark plug wire from the ignition coil
Remove the two 10mm bolts from the ignition coil
Pull the ignition coil up and out
2. Installing the New Ignition Coil
Push the new ignition coil into place
Insert the two 10mm bolts into the ignition coil
Connect the spark plug wire to the ignition coil
Push the hose bracket into place
Insert the 10mm bolt into the hose bracket
Connect the ignition coil wiring harness
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on this 2002 Chevy Suburban with the 5.3 liter, V8 engine. It's the same part and similar process on these Suburbans from 2000 to 2006. The items you'll need for this are a new ignition coil from 1AAuto.com and a 10mm socket and ratchet with an extension.
Your ignition coils are located right here. There are four on each side since this is a V8 engine. To remove these ignition coils, it's the same process for each of them; they're held in with two 10mm bolts. The only difference is this one right here that has a bracket for these hoses over it and that bracket also just held in with a 10mm bolt. We'll show you on this one since it's a slightly different procedure. Just lift up on the tab and disconnect that harness, and then, using a 10mm socket and ratchet, just remove that 10mm bolt, right there. Now you can just pull that bracket aside, and then, pull your spark plug wire from the ignition coil. Then remove the 10mm bolt at the top and the bottom of the coil. The coil will pull right off.
On the left, is the old ignition coil; on the right, is the new one from 1A Auto. You can see they're identical and they're going to fit exactly the same. Take your new ignition coil and push it down into place and then replace those two 10mm bolts. We'll fast forward as Don does this. Now reconnect your spark plug wire and then push this bracket back into place and replace that 10mm bolt. If you're replacing multiple ignition coils, obviousl,y you just repeat the process for each one and finally just reconnect the harness and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Dielectric Grease
You can move these heater hoses out of the way, just pull them out of the bracket and slide them to the side. Disconnect the wire at the plug. You can give it a twist and pull it off. Disconnect the wire at the coil, do the same. Twist it. Slide it right off.
Take the new one. This new one has a little bit of dielectric grease in it. But if it doesn't, you can always add some. Slide the part on into the coil, lock it in place. And then put the other part for the spark plug and lock it down. And you can do the same with the other ones. And move these heater hoses, put them back in the bracket.
ICA65503
In Stock
Product Reviews
Loading reviews
4.50/ 5.012
12 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
9
2
0
0
1
Good buy
Jordan
September 6, 2020
Bought these for my 01 yukon xl. Popped right in. Working good as of now. I live in Hawaii and the time it took to get here was not bad at all. Still a customer of 1A Auto with no complaints
Ignition coil kit
D
September 21, 2020
The kit was excellent. However, it was a misfit for the vehicle it was ordered, and I take responsibility for the misorder. It would have been helpful if the description of the coil highlighted its method of mounting. This would have prevented my error.
Although the error was mine, no issue was encountered when return and refund was requested. This is invaluable. Especially since errors randomly occur when its not possible to do a comparison prior to ordering a part.
As advertised. 1AAuto comes through for me again!
Robert
November 2, 2020
2000 GMC Sierra 1500 LTE 5.3 V8.
Products arrived on time, and were as advertised. Installation was occasionally challenging (not unexpectedly) but the parts from 1A Auto were just right. So far so good!
2005 Chevy Silverado
Pedro
May 3, 2021
My truck went from having misfire in cylinder 8, then multiple misfires.
Codes instantly cleared after installing new coil packs, wires, and spark plugs.
Truck still runs strong at 230K.
Thank you guys!
Perfect
Matthew
May 13, 2021
Everything worked and fit perfectly
Ignition coils!!
Jannett
June 2, 2021
I wouldn't recommend to purchase coils from here. They were cheap quality and made incorrectly. I was forced to use them because my car needed them and I had to make it work. But the coils kept falling apart on the magnetic side and not only that but they weren't made to fit my car like the car look up said it would fit. Not happy wouldn't recommend
Shannon
August 19, 2021
Excellent
Worked great but..?
Eleazar
November 2, 2021
Coils fit great and worked good after installing only problem was with the plugs , had to cut , modify them so they can connect to the spark plugs , or they would not connect and keep coming out , after that they work great
Christopher
February 18, 2022
Good choice!!!??????
Tyler
May 3, 2022
Good fit easy installation
Great experience, even when correcting an error. Thanks 1A!
Eugene
May 22, 2022
Had some slight issues, but I love this site and would recommend to anyone!
Paul
January 9, 2024
perfect fit, smoothed out the engine
Customer Q&A
I have a 5.3 vortec motor out of a 2006 1500 chevy truck. Will this kit work?October 31, 2020
Terry M
10
This kit is correct for the V8 motors out of those vehicles with the square style coils.
November 1, 2020
Adam G
Where is this part coming from?January 14, 2021
Walter S
10
We have several warehouses we ship from here in the US.
January 14, 2021
T I
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.