Kit Includes: (1) Passenger Side Tail Light (1) Driver Side Tail Light
Specification
Side Location
Driver & Passenger Side
Product Features
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Tail Light 1995-2004 Chevy Blazer S10
Created on:
Tools used
Phillips Head Screwdriver
1. Removing the Taillight Assembly
Remove the two Phillips screws on the side of the taillight.
Pull the light out and off.
2. Changing the Bulbs
Push in the tab and twist out the sockets.
Pull the bulb straight out.
Push the new one in.
Twist the socket back into place.
3. Replacing the Taillight Assembly
Twist out all of the sockets.
Unclip the harness from the taillight.
Twist off the rubber guide.
Twist the rubber guide onto the new light.
Twist all of the sockets into place.
Re-clip the harness to the light.
Line up the taillight and push it into place.
Replace the two Phillips screws.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
This video we'll be showing you how to replace the taillight, both the bulbs and the whole assembly if you break your taillight on this 2000 S10 Blazer, same as any S10 Blazer or S15 Jimmy of this era. The only tool you'll need is a Phillips head screwdriver.
Okay, to remove the taillight there's two screws on the inside of the rear hatch opening here. Phillips head, you want to remove those. Okay, we'll use a little bit of fast forward here so you don't have to watch me just taking these screws out. Okay, now the taillight comes right out. Okay, if you're just looking to change bulbs, these have little tabs that you press right here. Then they twist, come out, and then after that the bulbs just pull out and push back in. Okay, and if you're changing the whole assembly, you'll want to pull the little clip right here, clipping the harness in. Necessary to use your screwdriver just to push on the teeth a little bit and the other thing you could do here is use a pair of pliers to squeeze the teeth together. I didn't think of that while I was shooting it.
Once you get one side, push on the other side. That's the hardest part of the whole thing. Okay, when it comes out, you'll want to take this little rubber guide, twist it off. Here's my new light from 1A Auto. You can see it's the exact same, just quite a bit brighter and shinier. Okay, put that guide on. Now the gray one goes down on the bottom. Looks like that one's missing a, there should be a rubber. This one's, for some reason it's missing its rubber washer. Check the film and see where that went.
And after checking the film, it turns out that the rubber washer was never there in the first place. And put that pin back in. Now just like the original, make sure this pin gets lined up with that hole right there. Use the same screws. Harness is kind of getting in the way a little bit, just going to kind of push it in. There's my screw. Okay and we'll fast forward again as I tighten up those screws and then I walk to the front for what I hope to be a successful test. And it does appear successful.
We hope this helps you out. Brought you to by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.
LHT07467
In Stock
Product Reviews
Loading reviews
5.00/ 5.07
7 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
7
0
0
0
0
Great replacement!
Troy
January 30, 2017
Very clear with a unique twinkle. Great Upgrade fits perfectly. Eagle eye products are fantastic. Replaced the headlights and markers can't go wrong with 1A auto. Video was perfect. Shipping fast.
Perfect Fit!
william
June 12, 2017
Fit my 2000 Blazer perfectly. Very easy installation.
1995 Chevy c1500
Tim
August 29, 2019
Fit and work great.
Fast shipping
The videos are short and to the point.
Very helpful .
You make it look EZ
Will
October 6, 2021
I am confident that I can do this -- thanks for the video
Great Lights!
Gary
October 22, 2021
Great Lights! I replaced the 20 year old lights on the old Jimmy!
Great tail lights
Jane
December 13, 2021
They were exactly what I wanted! They look great!
I would recommend 1A Auto
Steven
December 29, 2021
Perfect fit, great price and fast shipping!!!
Customer Q&A
Do these lenses require led bulbs?December 20, 2022
John D
10
These are not LED taillights. But the test bulbs will need to be removed and either replaced with the OEM bulbs or new bulbs would need to be sourced locally.
December 21, 2022
Jessica D
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Oldsmobile is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Oldsmobile or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.