Replaces
Part Details
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a sway bar link on this 2002 Chevy Suburban, and it's the same part and similar process on these Suburbans from 2000 and 2006. We show you on the passenger's side, but on the driver's side it's the same procedure. The items you need for this include a new sway bar link from 1AAuto.com, a 14mm and 22mm socket and ratchet, locking pliers, a hammer, and a reciprocating saw depending on the condition of your vehicle.
Remove your hubcap by loosening up these lug nut caps and pulling the hub cap. Now, you want to remove the lug nuts. If you don't have air powered tools, you want to do this while the vehicle is on the ground. You can loosen them preliminarily, raise the vehicle and remove the lug nuts the rest of the way, and pull the wheel out. Using locking pliers, clip on to the top of your stabilizer link, and then remove this 14mm bolt. We'll just fast forward as Mike does this.
Now, you want to just hammer the link through. If the link doesn't move, you may have to use a reciprocating saw and cut it. Up top is the old part; below is the new part from 1A Auto. You can see they're identical, and they'll fit exactly the same. You want to put your stabilizer link back into place, starting with a washer and a grommet, then through the hole, then another grommet, then a washer, then the tube; then, before going through the next hole, another washer and grommet; then, on the top another grommet and another washer, then the nut.
Here, we just put the jack underneath the link. That's just to push it up through and compress the washers a little bit so that you can get the nut on the other end. Once I get another nut on, you'll see I just release the jack. You want to obviously be supporting the vehicle with jack stands, and then use your jack to push the bolt of the link up through. Then, you want to tighten up the sway bar link, and you basically want to tighten it up until the rubber bushings are compressed enough so that they're the same diameter as the washers.
Put the wheel back in place, then replace each of your lug nuts and tighten them up. You want to tighten them preliminarily, lower the vehicle, then tighten them the rest of the way. Torque each lug nut in a crossing pattern to 100 foot-pounds. Replace the hubcap, and just tighten up those lug nut caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts, installed correctly that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to replace the sway bar links in this 2002 GMC 2500HD, basically the same as most '88 to '06 GM pickups, SUVs, vans; also the same as a couple of Ford applications. Tools you'll need are a jack and jack stands for some vehicles, 14 mm socket and ratchet or whatever is correct for your link, they could be different depending on application, an adjustable wrench, and some penetrating oil.
Your stabilizer link is right up underneath. This big bar here is your stabilizer bar, and then here is your control arm. It's connected by this, which is the stabilizer link right here. This can break. Also, these bushings, these rubber bushings can wear out, which will cause a rattling sometimes when you go over bumps. You have a good idea if it's the stabilizer link if, when you go around a turn, the rattling stops. I'm going to show you how to replace that.
On top, you're going to want to spray some penetrating fluid. This is a 14 mm bolt down here at the bottom. What you're going to want to do is put an adjustable wrench onto this side. This is an original link here, so the thing on top is kind of bolt-shaped. I've got that on there to hold it. Now I'm going to attempt to slowly unscrew it.
The bolt comes down, and that can come out. Then you can see, even though there's nothing too terribly wrong, you can see that this one is worn, right in here, so we'll replace it. On the original you can see this top nut has edges to it so you can get that wrench on there to hold it in place. We've gotten it out of there, but we still have this in place. Just pull that right out, like that. I'm going to take my new link and I'm going to put it up through. This bushing has the ridge up into the control arm. Then I'm going to take a bushing down and then a washer on top of that, then my spacer. Then I'm going to take a bushing and a washer, and now the step goes up into the sway bar. Then just push that.
In order to get this in, what I've done is this is a little jack. If you're doing this just on the ground, you can do the same thing. Put the jack in underneath the stabilizer bar here, lift it up, and create plenty of room to push that up through. Then you want to make sure these bushings all go right into the holes in the stabilizer bar, right there, and the control arm. This last bushing goes with the ridge down, then the washer on top. I'm going to put the jack right in underneath here, push this up in to get the nut on.
I've got this together and I've got the nut started on there. I'm going to replace the other side first before I tighten it up. I wouldn't take apart the other side here you can see, this is the one from the driver's side and this is the one from this side, so you can see this whole part was rough and it broke off. It's possible this link wasn't really doing anything anyways. This here that broke off of this one is stuck inside there. What I'm going to have to do is I'm going to have to actually cut this link with my Sawzall. I'm going to do that very carefully, because I don't want to contact the boot or anything else. I don't want to contact the CVs. I just want to cut through the link itself.
Now with the car on the ground, you want to tighten up the links. I'm just using an air ratchet. You can hand tools, obviously. Tighten up both sides and you're done.
We hope this helps you out. Brought to you by www.1AAuto.com- your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
