Replaces
Replaces Ford F150 Front 8 Piece Steering & Suspension Kit MOOG MGSFK00242
$430.95
Replaces Ford F150 Front 6 Piece Suspension Kit MOOG MGSFK00239
$281.95
Replaces Ford Lincoln Front 4 Piece Suspension Kit MOOG MGSFK00238
$244.95
Replaces Ford Lincoln Front Driver & Passenger Side Upper 2 Piece Control Arm with Ball Joint Set MOOG MGSFK00098
$169.95
Replaces Ford Lincoln Front Driver Side Upper Control Arm with Ball Joint MOOG RK80306
$92.95
Replaces Ford Lincoln Front Passenger Side Upper Control Arm with Ball Joint MOOG RK80308
$92.95
Replaces Ford F150 Lincoln Mark LT Front Lower Ball Joint MOOG K80149
$59.95
Replaces Ford F150 Lincoln Mark LT Front Outer Tie Rod MOOG ES3691
$58.95
Part Details
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Item Condition:
New
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the front struts. This is a 2005 Ford F-150. It's exactly the same for any 2004, the new body style, through the 2008, and probably the same for 2009 and up. We show you on the driver's side, but the passenger's side is the same procedure and we do recommend you replace them in pairs. You'll need new front struts from www.1aauto.com, sockets from 8mm up to 30mm, a pipe or a breaker bar for leverage, a 12mm 12-point socket, 18mm and 21mm wrenches, pliers, pry bar, flat blade screwdriver, torque wrench, hammer and jack and jack stands.
Start off by prying off the hubcap. Then loosen up these lug nuts using a 21mm socket and ratchet and a piece of pipe for some extra leverage. Then raise the vehicle, and remove them the rest of the way and take the tire off. You want to life the whole front of the car up and put it on jack stands with both wheels off the ground. Now pull the wheel off. Now turn the wheel, and remove this 21mm nut at the top of your outer tire rod. Then once you remove it, you want to just put it back on just a couple threads.
Now hammer the knuckle until the outer tire rod drops down. Now you can remove that nut, and just set your outer tire rod off to the side. Underneath your control arm, on the bottom of the sway bar link you want to just remove that nut. You can try doing it with an 18mm ratchet, but most likely it's going to start spinning, and the solution for that is an 18mm wrench and an 8mm socket and ratchet. Then you can just remove that nut. You want to spray the bolt that holds the bottom of your strut, and then a 30mm socket. I'm using a breaker bar and a piece of pipe and break that free. Then once you get it going, the bolt will most likely spin. Hold the bolt end with the 27mm socket and take that nut off.
Then spray these 15mm nuts at the top of the strut with some penetrating fluid, and remove two of them all the way. The other one, you just want to leave on a few threads. Using a pair of pliers, remove this cap. Then loosen up and remove that 13mm nut. Then you want to just put it back on just a few threads. Tap it with a hammer and make sure it goes through. Then remove the nut the rest of the way. On the other end of the axle, there's a series of 12mm bolts. You just need to use a 12mm 12-point socket, and then a pry bar to hold the wheel. Just loosen those up.
You can also just have a helper get in the vehicle, and hold the brakes to hold the axle in place. When you remove that last one, just push the axle down to the side. Now spray this 21mm nut up here on the bottom of your upper control arm. Then remove that nut, and put it back on just a few threads. Now with the nut back on a few threads, just hammer the wheel knuckle until the upper control arm loosens up. Now just lift up on the wheel knuckle, and then remove that nut. Now you can just set the wheel knuckle off to the side carefully.
You don't want it to strain those brake hoses. Then just tap the axle and pull it out of the wheel knuckle. You want to feed the axle towards the left side towards the front of the vehicle. Then just angle it down, and pull it down and out. Now, we're just going to check up underneath the control arm a little bit. The vehicle is still supported on the jack stands under the frame. Remove the bolt from the bottom of the strut, and you can see the struts in there are still loose. Make sure the nuts on the top of the strut are removed. Pry the strut out.
Up top is the old strut. Below it is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Feed your strut up into place. Push those studs through. Then just replace those nuts at the top to just hold it. You don't need to tighten them up right now. You're just putting them there to hold it in place. Then pry the bottom of the strut back into the lower control arm. Then push that bolt back through. You just make sure it's all the way in. Then replace the nut and tighten it up preliminarily. We'll just fast-forward as Mike goes back over those 15mm nuts making sure they're tightened. Then you can remove the jack.
Feed your axle back into place. You want to feed it back in the same way that you pulled it out. Then just angle it back down into the hub and push it in. Now you can take your upper control arm and push it back into the wheel knuckle. Once you push it through, just put that 21mm nut on there to hold it in place. Line up the axle and replace those 12mm bolts. We'll fast-forward as Mike does this. Now tighten each of those to 60 foot-pounds in a crossing pattern. You can see we torqued that one. Then you want to turn the wheel until you get the one on the opposite side. Then torque that one. You want to just repeat this process with each of them. Now replace this 13mm nut and torque it to 20 foot-pounds. Then replace that cap and just tap it into place.
If any of the lines on the back came undone, make sure you push them back in and re-clip them. Then push your outer tire rod up to the wheel knuckle and replace the nut. Then torque that to 111 foot-pounds. Now just tighten up this bolt on your upper control arm. If the stud spins, use a 10mm socket and ratchet. Then you want to torque this to 111 foot-pounds. Then tighten up the nut on the bottom of your sway bar link. Jack up underneath the lower control arm to simulate a wheel being in place. Torque the lower strut bolt to 150 foot-pounds.
Now we'll fast-forward as Mike replaces the wheel and replaces the lug nuts and tightens them preliminarily. Then he lowers the vehicle and tightens them the rest of the way. Then torque each of them in a crossing pattern to 120 foot-pounds. Then just replace your hubcap and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Okay, friends, to get started on this job, the first thing that we need to talk about is safety. You want hand protection and eye protection at all times. With that said, safely raise and support your vehicle so you have your front wheel off the ground. We're going to remove this center cover, and then we're going to remove the lug nuts as well. Get your wheel off of here. Okay, now that the wheel is off, we have a nice, clear view of our inner tie rod end. We need to loosen this jam nut right here, I like to use a nice big pair of pliers. Give that a little turn, grab it. There we are. Make sure it's broken free.
Now, we're going to remove our outer tie rod end nut. To remove your outer tie rod end, it's best to hit right along the knuckle. If for some reason that isn't working and you don't have a threaded area along the top of your tie rod, you could carefully try to bonk along the top as well. Now that we have the tie rod out off, we can move this around. And that's great because we want to be able to get this caliper off. Something, before we do that that I want to mention, is that this rotor right here is going to have a little bit of weight. To do the lower ball joint, we're going to have to take off this whole unit right there. So, of course, that's going to weigh something as well. If you have an issue with something that's heavy, it's probably a great idea to go ahead and remove the rotor as well but, of course, that'll make more work so you'll have to clean up the surfaces in between the wheel bearing and the rotor.
Next, we need to get our ABS wire off of our brake hose. After that, we're going to remove our two caliper bracket mounting bolts. That's going to relieve the caliper and we're going to move it away from the rotor area. Once you do that, you need to have something ready so you can hang the caliper. You don't want to put any pressure on your flex hose. I've got my little bungee cord ready. Just going to put that in a couple of threads. Remove that bolt. All right. Now, we'll just set this up. Next, we need to follow our ABS wire. If you were to give it a tug, you're going to see this area right here moving around. That's because that's where it's attached to on the backside of the plastic. I'm just going to use this little forky tool, you can use pretty much whatever you've got. Give this a little flex, and I'm going to see if I can get behind there and just relieve it from the plastic.
Okay. Pull this through. Now we need to disattach this. If you were to push on this tab and then draw this away, it'll separate the two. We're going to get this off of here as well. And then, of course, we'll bring the ABS wire all the way down to here and we'll wrap it up so it's as safe as possible. At this point, I always like to move down to the lower ball joint. I'm going to get this cotter pin out of here, and I'm going to loosen up this nut. I'll leave it back on a couple of threads and then we're going to move up to the upper ball joint. Let's get this nut off of here. Just leave that on a couple of threads as well.
Next, we're going to take our hammer and we're going to bonk right along here on our knuckle. You want to be careful not to damage your upper ball joint boot. So, now that we have the upper ball joint out of there, you want to make sure that you tie up the knuckle so it's going to be semi-safe, it's not going to be just flopping down because the next thing we need to do is relieve our lower ball joint. When we do that, we're going to do approximately the same thing. We're going to hit right along here on the knuckle, try to cause vibration, and hopefully, this area will separate.
There you are. As you can tell it's separated, our safety nut did its job, and, of course, the upper area that we tied up is also keeping us safe. So, we've got that untied now, I'm going to relieve the nut. You need to lift up on the knuckle and keep in mind that it's going to be a little heavy. Let's get the knuckle right off of there. And we have a nice, clear view of our lower ball joint at this point. We want to remove this grease fitting right here. Once we've done that, we're going to remove the snap ring and we'll move along.
Get this right off of here, I'll show you what it looks like in a sec. So, this is what the snap ring looks like. You need to go ahead and get some of these little pliers, you get into those little circles, as you squeeze, it spreads it, and it'll come off with the lower ball joint. You could use your hammer, give it a whole bunch of bonks and drive it right out of here, but you might, of course, damage your lower control arm, nobody wants that. I'm going to use the ball joint tool and I'll show you how to press it out. Here's the tools we're going to need. The ball joint press itself, you're going to need a cup that fits over the lip of the ball joint, but still fits on the control arm, and then, of course, you're going to need one of these that has the slot for the stud. Put these like this, just like that. Take your press, put it over, and go ahead and bottom it out. Now, as we drive this down, it's going to push the ball joint through. Once it breaks free, the whole going to kind of flop around. So make sure you have a good grip on it.
You can see it starting to go down, and there's our lower ball joint. Now it's going to be time to get ready to install our brand new lower ball joint. Something to pay attention to is to press this in, you're going to need to get on this lip area right here, except not on this portion, on this portion. As you can tell, the boot's in the way. Take a small pocket screwdriver and just see if you can weasel your way in between the lip and the boot and separate the two. Obviously, be very careful, you don't want to damage the boot. We'll get that out of the way and now we can continue. It's always a great idea to clean down the area you're going to be working. Make sure you clean out that hole, you don't want any debris in or around it. To install our new lower ball joint, you're going to need something that looks like this.
It has a little cupped area. The reason for that is because it needs to go over the hole on the lower control arm where the lower ball joint is going to come up, and then through. If you put a flat plate here, obviously, the lower ball joint is going to be able to come up far enough to be able to put your clip on there. So, we'll say that's there, take your lower ball joint, and then, of course, you need another cup. The lower cup needs to have a hole for the stud to go through and it needs to be just thick enough or wide enough that it can fit along the lip of the lower ball joint. Just like this. Go ahead and line this up. Now we're going to get our ball joint press, put it together, and then, of course, as we start tightening it, it's going to pull this up and into the lower control arm. So, now we need to make sure we align this upper cup up because if it's off by a little bit, it's a possibility we could damage our lower ball joint. Now we're going to tighten this. What you want to pay attention to as you tighten it is to make sure the ball joint is going straight up. If it seems like it's going like this, obviously, you're going to have an issue.
So, you can see right here, it looks like it's starting to go at an angle. I'm going to stop there, relieve tension or pressure, I'm going to move this a little bit and see if I can get that side to go up. As you can see, as I'm pressing this up, you want to make sure you don't have any gap between the ball joint and the lower control arm itself, so I need to continue going up. Once it's bottomed out, leave it just as it is. Hit right on the lower control arm with your hammer a couple of times, just to cause vibration and that's going to settle this in just in case it's a little off-kilter. That's great. Let's get this out of here.
Now, let's get this clip on here. Okay. Make sure it's sitting all the way around. You want to make sure it's inside the groove. If it's not in the groove and it's possible that it could fall off, there's also a possibility that the lower ball joint might not be secure. Now it's going to be time to get our boot on here, just line it up on one side and then take some pliers and just help it up all the way around. You want to make sure it's completely secured so it can keep the moisture out. Make sure it's secure. Let's move along. Something that I always try to pay attention to is the area where the cotter pin is going to go through. Obviously, if we're going to have that big old knuckle on here with the rotor, it's going to be very hard to get a cotter pin in between and inside there. So, use a flat-head screwdriver, use a pick, whatever you need to do, give it a spin, so it's facing front to back. Perfect. Now it's going to be time to get our knuckle on here. Make sure you have your lower ball joint nut in your hand because it's going to make your life much easier, slide it up on, start that ball joint nut on.
Now, we're just going to snug up that lower ball joint nut. The reason for that is because I want to make sure there's no way that it can come loose on me while I continue working. Stop right there, we'll move along. Next, we're going to need to get our upper ball joint into the knuckle. That's going to be easiest if you have a nice pry bar like this. What we're going to want to do is go above the control arm right here, and then find an area in the frame that'll make it so we can go into and be able to pull this down. Leave the bar right where it is, line this up. Go ahead and pull this down now and start your upper ball joint nut.
Now it's time to torque these down. Let's torque this upper ball joint nut to 85 foot-pounds. Now, let's torque this lower ball joint nut to 111 foot-pounds. Now it's going to be time to put in your locking cotter pin. If for some reason you notice that the slots on your nut don't line up with the hole on the ball joint, you need to continue tightening that nut until you get to the next slot. You do not want to loosen it, just check it. Well, that one actually lines up perfect. Go ahead and peen it over. I'm going to grab some pliers and cutters.
Make sure it's 100% peened over and there's no way that that locking clip or cotter pin can come out. Next is going to be time to get our caliper back on there. You want to inspect your bolts, make sure they're in good condition. If for some reason the threaded area looks like it's rotted or it has any type of never-seize or anything inside of it, you need to make sure you clean them up and get off any never-seize. Of course, the area on the bracket where the caliper bolts are going to go to, make sure those are clean as well. Once you have your bolts cleaned up, let's go ahead and get this caliper ready for install.
I'm going to slide the pads over the rotor and then line up the holes for the bolts to hold the caliper to the knuckle. It's a great idea to use a little bit of thread locker if you have access to some, but we'll call it your prerogative. Bottom these out, and then we'll torque them down. Torque these to 148 foot-pounds. Now let's get our ABS wire re-secured. Go ahead and reattach it back to the flex hose going up to where it's going to be secured up here, come up this way, get this back on here. If for some reason any of your clips are broken, you need to make sure that you have your ABS wire secure so there's no way it can get damaged by the wheel as it comes around, or, of course, driving the vehicle in any way. Reconnect this in, give it a nice tug to make sure it's 100% in. Put this all behind the nice plastic here, and then re-secure it in the backside.
Now it's time to get our outer tie rod end into the knuckle. Let's see if I can just turn it a little bit, slide it in here. There we are. Take our nut, If it has a lock, make sure the lock is facing up, of course. Now, we're going to snug it down and then we're going to torque it to 111 foot-pounds. Now it's time to get our wheel back up on here. We'll start on all of our lug nuts, bottom them out. And then we're going to torque them to 150 foot-pounds. Next, you need to get your vehicle so the tire's just barely on the ground so it can't spin. We're going to torque the lug nuts like I said to 150 foot-pounds in a star pattern. Once you've torqued it, make sure you put it back on your center cover, of course. Okay, friends, anytime you do any type of front-end work on your vehicle, it's always super important to make sure you get your vehicle down to a reputable alignment shop. They're going to take care of you and make sure you're going straight on down the road. Be safe out there.
Tools used
Okay, friends, one of the first things we need to do to get started on this job is to safely raise and support the truck. After you've done that, remove your center cover here. And then remove all six of your 21-millimeter lug nuts and get the wheel off. Now that the wheel's off, let's go ahead and get this ABS wire disconnected. I'm just gonna come right along here and then remove this 8-millimeter bolt. Now let's go ahead and remove our anchor bolt for our flex hose for the brakes. Let's go ahead and remove this little center cover. Now let's remove our axle nut. Now we're just gonna push on this axle stub here. If it doesn't move, just go ahead and put the nut back on a few good threads, and then give it a couple of loving bonks with a hammer. Now let's go ahead and get our cotter pin out for our tie rod. Set that aside for recycling. Let's remove the nut.
Now we're gonna use a hammer, and we're gonna hit right on the knuckle right here to try to break this free. Now let's remove our upper ball joint nut. Now we're just gonna separate these two. Now, the next thing we need to do is remove the bolt that's gonna be holding the front strut to the actual lower control arm. I'm gonna hold the bolt side on this with a wrench, and then I'll, of course, remove the nut. There we are. The next thing we're gonna wanna do is carefully pull down right along here, and then we can separate these two. Let's just go ahead and spray those mounting bolts from the top there. Now we're gonna go ahead and remove those three mounting nuts. All right. So that's almost off of there. Let's leave it on a couple of threads, and then we'll fully remove the other two.
There we are. All right. So now we're back to our last nut here. Let's make sure we hold up on that front strut so it can't fall out on us. All right. There it is, friends. Now that we have the front strut out of the way, we have a clear view of our mounting bolt that holds our control arm to the frame. I would just go ahead and use the swivel with an extension and then I'm gonna come in right like this. You can, of course, just use a 21-millimeter socket or wrench, and then I'm gonna come to the other side with another 21-millimeter, and I'm gonna hold that nut. It's nice and loose. Let's go ahead and get that nut off of there. There's the bolt. We'll do the same to the other side.
Okay. Get that nut off of there. There it is, friends. Now it's gonna be time to install our brand new upper control arm. Let's go ahead and slide this in. We're gonna line up those bolt holes, start them from the inside going out. Now let's just take a nice pry bar, stick it in here like this so it's holding, and then we're gonna put our control arm on top of it. That's gonna have the control arm so it's sitting in the same position as if we were on the ground. Go ahead and start on both of those nuts, and then we'll go ahead and snug them up. Snug it up. Now let's torque these to 111 foot-pounds. All right, friends, let's go ahead and get our strut up in here. Start all of your nuts, snug them up.
All right. Let's get this lower aspect in. Start the nut on there. Now we're gonna apply a little bit of pressure underneath the lower control arm so we can bring this up so it'd be almost like it's sitting on the ground, and then we'll go ahead and snug this. Go ahead. Let's snug this up. Let's torque this to 406 foot-pounds. Now with pressure still underneath there, let's go ahead and torque these upper mounting bolts as well. We're gonna torque these to 30 foot-pounds. The next thing we need to do is get our axle inside the knuckle as we push the knuckle up. You wanna be very careful not to damage your internal seal.
Now, I'm just gonna take a pry bar, come in and under here, and then I'm gonna try to put the ball joint through the knuckle. Go ahead and start that nut, snug it up, torque it to 85 foot-pounds. What you wanna do next is make sure that you have your slot lined up with the hole on your ball joint stud. If for some reason it isn't, you need to continue tightening until it is. Next, take your cotter pin, go ahead and put it through the slot and the hole, and then, of course, lock it down. Let's get our sway bar back up on here, start on both of the nuts, snug them up, and torque them to 41 foot-pounds. Do the same to the other side of the vehicle. Let's make sure we install our grease fitting. Apply some grease. The next thing we're gonna wanna do is put on our axle nut. I like to use a little bit of red thread locker, bottom it out, and then torque it to 20 foot-pounds.
Now that that's torqued, we're gonna go ahead and install this cover. You wanna make sure that it's not damaged in any way, go ahead and slide it right on there, and bottom it out. Now, before we can continue on to putting the brakes together, we wanna make sure that the hub mating surface and the back of the rotor mating surface is nice and clean. After you've done that, apply a little bit of copper Never-Seez. Let's go ahead and get our rotor back on here. I'm gonna start a lug nut on so it holds the rotor for me. Let's get our caliper reattached. We're gonna use some thread locker, of course, on the bolts. Start them both in, and then we're gonna torque them to 185 foot-pounds. Let's get our vacuum lines reattached. Now we're gonna reconnect in our bracket, ABS wire. Let's snug them up. Let's start resecuring our ABS wire. Make sure you go up and in between the brake line here, just like that.
This looks good for now. Make my way down here. Get a little push clip. It's gonna go into your hole right there. The rest of it should just line up. We'll continue on. Making our way up here, let's make sure we reconnect in our ABS wire, listen for a click, and then, of course, give it a nice tug. After that, you wanna make sure that you secure it back in up here. Make sure everything's nice and secured, and it's definitely not rubbing up against anything, and there's no way it can get caught. Let's get the outer tie rod end on here, snug this up, torque it to 85 foot-pounds. The next thing we wanna do is make sure that our slots line up with the hole in the stud for the tie rod. If for some reason it doesn't, you need to continue tightening until the next one does. Install your locking cotter pin and then lock it down. Let's get the wheel back up on here. Start all of your lug nuts, snug them up, and torque them to 150 foot-pounds.
Torqued. Okay, friends, so that's pretty much it. Aside from making sure you pump up that brake pedal, and then get yourself safely down to an alignment shop.
Tools used
