TRQ ignition coils will have your engine running like new. TRQ ignition coils are manufactured to precise specifications using premium raw materials to optimize each vehicle's ignition system. To ensure peak performance, TRQ recommends replacing ignition coils in sets to prevent electrical output imbalances. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
High dielectric epoxy and reinforced bobbins for extended service life
Rubber, Silicone, or Phenolic Resin Shell: Prevents premature boot wear
Application Specific Design: No modifications required
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Ignition Coil 2006-10 Pontiac G6
How to Replace Ignition Coil 2010-16 GMC Terrain
Created on:
Tools used
10mm Socket
Ratchet
1. Removing the Engine Cover
Remove the oil cap
Remove the engine cover
Twist the oil cap on
2. Removing the Ignition Coil
Remove the 10mm bolt from the ignition coil
Pull the coil out
Push down on the gray clip
Disconnect the coil harness
3. Installing the Ignition Coil
Connect the coil to the harness
Push up on the gray clip
Push the coil in place
Insert and tighten the 10mm bolt
4. Installing the Engine Cover
Remove the oil cap
Remove the engine cover
Twist the oil cap on
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an ignition coil on a 2007 through 2010 Pontiac G6. It's exactly the same for cylinders 1 through 4. All you will need is a new coil pack from 1A Auto and a 10mm socket and ratchet.
Remove the engine cover by removing the oil cap first, and then pulling it up and off. Reinstall the oil cap for now, just so nothing falls down inside. On top of the engine, you'll find your 4 ignition coils: 1, 2, 3, and 4. Use a 10mm socket and ratchet to remove the bolt. With the bolt removed, pull the coil pack and wires out. Pull down on the grey little clip there, just an eighth of an inch, and then push down on the tab and pull the connector off.
Here, we're showing you the old part. The new coil from 1A Auto is a direct replacement fit, identical part. Put the new coil back onto the harness, clip it in, push the grey clip back in all the way, then seat the coil pack down. Take your bolt and tighten it back up. Fast-forward putting that bolt back in. Now, if necessary, replace the rest of the coil packs, then reinstall your engine cover by taking your oil cap off, put the cover down into place, seat it, and then put the oil cap back on.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Flat Blade Screwdriver
10mm Socket
Ratchet
1. Accessing the Ignition Coils
Disconnect the small hose from the air intake box
Use a flat blade screwdriver to loosen the upper and lower hose clamps
Remove the oil fill cap
Pull the engine cover up and off
Put the oil fill cap back on
2. Removing the Ignition Coil
Push back the white clip on the ignition coil wiring harness
Disconnect the harness
Remove the 10mm bolt from the coil
Pull the ignition coil out by hand
3. Installing the New Ignition Coil
Push the new ignition coil in by hand
Insert the 10mm bolt
Reconnect the wiring harness
Push the white clip on the harness in
Repeat Steps 2 and 3 for the other coils as necessary
4. Reinstalling the Engine Cover
Remove the oil fill cap
Put on the engine cover, lining up the three pins
Push on the air intake box using the two tabs
Push the hoses into the air intake box
Tighten the hose clamps with a flat blade screwdriver
Push the smaller hose into the air intake box
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the ignition coil on this 2014 GMC Terrain with a 2.4-liter four-cylinder engine. The only tool that you're going to need for this is a flat-blade screwdriver and a 10mm socket and ratchet.
Start off by disconnecting this hose. Then you want to loosen up this clamp. There's another one right down here. As you can see, you just need a flat-blade screwdriver and loosen up that bolt. Once both of those are loosened, pull the hoses free, and then lift that box up and off. Now, remove your oil-fill cap and pull up the engine cover. Replace the oil cap so nothing falls down into the engine.
Right here are your ignition coils. Push back on the white clip. Then, push the tab on the harness and pull it free. Then, using a 10mm socket and ratchet remove the 10mm bolt. Then, the ignition coil will pull up and out. Take your new ignition coil and push it down into place. Then replace that 10mm bolt. Repeat the process for any of the other coils you might want to replace.
Reconnect your harness and push that clip back in. Remove your oil cap. Line up these three holes with these three pins. Push your engine cover down into place. You want to line up those two holes with those two tabs and you want to push your upper hose into place. Then push that lower hose into place. We'll fast-forward as Don tightens up those two hose clamps. Then, push in that smaller hose and you're all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
ICA61804
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Saturn is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Saturn or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.