Replaces
Replaces Cadillac CTS Front 10 Piece Steering & Suspension Kit TRQ PSA65113
$629.95
Replaces Cadillac CTS Front 8 Piece Steering & Suspension Kit TRQ PSA65112
$589.95
Replaces Cadillac CTS Front 6 Piece Suspension Kit TRQ PSA65111
$574.95
Replaces Cadillac CTS Front 10 Piece Steering & Suspension Kit TRQ PSA69605
$564.95
Replaces Cadillac CTS Front 8 Piece Steering & Suspension Kit TRQ PSA69610
$529.95
Replaces Cadillac CTS SRX STS Front 6 Piece Suspension Kit TRQ PSA69654
$481.95
Replaces 2008-13 Cadillac CTS All Wheel Drive without Magnetic Ride Control Front & Rear 8 Piece Suspension Kit TRQ PSA27976
$474.95
Replaces 2008-13 Cadillac CTS All Wheel Drive without Magnetic Ride Control Front & Rear 4 Piece Complete Strut Assembly & Shock Absorber Kit TRQ SKA27997
$434.95
Replaces 14 Piece Ignition Kit DIY Solutions ENG00693
$424.95
Replaces Cadillac CTS Front Driver & Passenger Side Upper & Lower 4 Piece Control Arm with Ball Joint Set TRQ PSA65110
$406.95
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including 1,3-Butadiene, which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Release our hood. Pull the handle inside. Go underneath. Find the safety right here. Lift it up. It has two positions, normal position and then a service position.
Serpentine belt is at the front of the engine. There's only one on this vehicle. We're going to remove this cover. There's a 10 millimeter bolt here. Use a 10 millimeter socket ratchet extension. Pull the bolt out. There's a little stud that it's sitting on. You just pull it straight out. Just like that. Put this aside.
Use a 14 millimeter socket and a breaker bar, and place it down here on the spring loaded tensioner. Get this set up here. Pull it towards the driver's side. You can pop the belt right off. The idler up here. Let the tensioner go. Pull this out of the way so it doesn't fall. Feed the belts off all the pulleys. Take the belt right out.
This is our original belt, and our brand new one from 1A Auto. Just came out of the package with the same number of ribs. It is the same length, so it'll fit great and work great on our vehicle.
Now, start by going around the crank pulley. Goes up and over this lower idler. Then it goes down around the water pump. Goes up and around the A/C compressor. Go down around this other idler. Up and over the alternator. Be sure to get it seated in the pulleys. Then it's going to go, when I move the tensioner, it'll go over this little idler pulley on the outside here. Put the breaker bar socket on. Push this down. Make sure it's seated all the way. That will hold it up. Give it the tiniest amount. The best is brand new, so it doesn't have much stretch to it. Make sure it's all the way in. There it is. Release the tensioner. The belt is installed.
Reinstall the cover, and push this pin into that rubber grommet. Reinstall this retaining bolt, and just tighten in down. Put the hood down.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
