Replaces
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Open the hatch. Tail light is held to the body. Two 10 millimeter bolts and a clip that's out here. These also have a Phillips head opening in them. You can use a Phillips head screwdriver. But I'm going to use a 10 millimeter socket and ratchet. It's a little bit easier. They shouldn't be in there very tight, and they should come right out. Put this bolt aside so I don't lose it. I want to move to this side.
Basically there's a clip right here, so it needs to push straight out. There's a couple pins holding it in. I'm going to push from the back. It does sound like it's breaking, but it takes a good amount of force to get it free. I was sliding it off of this pin that slots into here in the tail lamp, and then it also needs to come off the two little pins here that are located here. Once it's out, there's a main connector.
Now push in the lock. Pull it out. The whole tail light assembly can be removed now. To reinstall it plug it into the main harness.
To reinstall it, we're going to want to line it up and slide it over that pin. And it's also going to slide over these locating pins here. So get it just lined up like that, push it over, and push it straight in. It'll snap when it's in place. Reinstall the bolts. Do the same for the other one. This procedure will be the same for both sides.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years. We're dedicated to delivering quality auto parts, expert customer service, fast and free shipping, all backed by our 100% satisfaction guarantee. Visit us at 1AAuto.com, your trusted source for quality auto parts.
Right here is the tail light, and you're going to want to remove these two 10mm bolts. I'm using a 10mm socket and extension and a quarter drive ratchet. We'll start by spinning these out. As soon as you crack them loose, you should be able to take them out right by hand because they're not all that tight. Once the two screws are out, you should be able to pretty much pop this right off just by pulling it straight out. You can see there's a few tabs right here. It slides on this tab, and then there's two little push pins that it pops into. From that point you can take it right off the car just by unplugging that one connector.
Putting the taillight back on, you'll want to connect this connector. Then you want to make sure that you line up this groove and these two push pins so that it sits on the car appropriately just like that. Now you'll take your two 10mm screws. You always want to start them by hand without any real force on them so that they don't crossthread. Then you can tighten them up with your ratchet and extension.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
