Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Lens ColorTinted Lens
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Tail Light 2003-04 Toyota Corolla
Created on:
Tools used
Flat Blade Screwdriver
10mm Socket
Ratchet
1. To service the bulbs
Pop the trunk and pull out the little section of padding.
Twist and pull out the bulbs to service them.
2. Remove the tail light assembly
Untwist the plastic thumb screw anchoring the trunk padding.
Pull the trunk padding back.
Remove the three 10 mm bolts and unplug the wiring harness.
Pull the tail light assembly out.
Swap your bulbs to the new tail light assembly.
Remove the old gasket.
3. Install the new tail light assembly
Put the new tail light seal gasket in place.
Place the tail light assembly into its mounting
Plug in the wiring harness
Use a 10 mm socket and ratchet to bolt down the tail light assembly.
Replace the trunk padding and screw in the thumb screw.
Tuck the bulb padding panel back into place
Brought to you by 1AAuto.com, your source for quality replacement parts, and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20+ years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you, and enjoy the video.
In this video, we're replacing the tail light on this '07 Toyota Corolla, same as any '03 to '08 Corolla. The only tools you'll need is a screwdriver and a 10-mm wrench. And the tail lights in this video, we do sell. So visit us at 1AAuto.com, and get a nice, new replacement.
If you're just looking to remove the bulbs and change the bulbs in your light, you can do it just by pulling this little access panel back. Then you can get your fingers in here and twist and pull it off. And then there's your yellow blinker bulb. The other bulb's up here. But if you need to replace your whole tail light assembly because you had a little run in with something, you remove that one screw there. Going to pull your padding back, and there's three bolts, one, two, three. With a 10-mm, I'm going to remove those. Disconnect. There's a little tab here. The easiest way I've found to do it is to just get your screwdriver in there, push on the tab.
Once you have it unbolted and unplugged, you can pull the inside out first. Work it out. And then this little gasket kind of wants to some with it. There's our light, the new light from 1A Auto. You can see, this is the 1A Auto light. It's all the same. You do want to swap your bulbs over. And also our light does come with a new gasket, so you can remove this gasket. You want to use the new gasket, because it will seal out the water better. So I'm going to put this light back in because there's really nothing wrong with it. I'm just using it to show you how to do it. But you can see, our light's going to go in just like the original, and it even comes with a new gasket.
So then I'll just need to put the light back in, and put all the bolts back on. Okay, now you plug in the light, put this back on this little stud, and put this back in place. Push it all down into the gasket. Put your padding back on. Take this, just try and stuff the corners in.
We hope this helps you out. Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person. Thank you.
LHT07895
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Toyota is a registered trademark of Toyota Motor Corporation. 1A Auto is not affiliated with or sponsored by Toyota or Toyota Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.