Replaces
Replaces Toyota Lexus 6 Piece Ignition Coil Set Delphi DEERK00013
$399.95
Replaces 2009-16 Toyota Venza Front & Rear Ceramic Performance Brake Pad & Rotor Kit TRQ Performance BKA21781
$259.95
Replaces Toyota Highlander Venza Rear 4 Piece Suspension Kit TRQ SCA67179
$249.95
Replaces 2009-16 Toyota Venza Front & Rear Ceramic Brake Pad & Rotor Kit TRQ BKA11671
$239.95
Replaces Toyota Highlander Venza Rear Driver & Passenger Side 2 Piece Strut & Spring Assembly Set TRQ SCA57391
$229.95
Replaces Toyota Highlander Venza Rear 4 Piece Suspension Kit TRQ SCA67193
$224.95
Replaces 2009-16 Toyota Venza Front & Rear Ceramic Brake Pad & Rotor Kit TRQ BKA23125
$224.95
Replaces Toyota Venza Front & Rear 4 Piece Performance Brake Rotor Set TRQ Performance BRA15184
$194.95
Replaces Toyota Highlander Venza Rear Driver & Passenger Side 2 Piece Strut & Spring Assembly Set TRQ SCA57372
$192.95
Replaces Toyota Lexus Scion Tire Pressure Monitor Sensor Assembly 4 Piece Set Dorman OE Solutions 1ATPK00033
$185.45
Part Details
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Hi, I'm Mike from 1A Auto. We've been selling auto parts for over 30 years.
Hi, everyone. Sue here from 1A Auto, and today we have a 2013 Camry in the shop and I'm going to show you how to change the fog light assembly that is from 1A Auto. If you need this part or any other part for your car, click on the link below and head over to 1aauto.com.
So we're going to take the undercarriage splash shield down that's attached to the bumper with a 10 millimeter socket. We're just going to go from one side. Walk our way over to the other.
To remove the fog light, now we can put our hand up in here in the Phillips screw, that one mounting screw. I'm using a stubby screwdriver. And you back that screw out. Then you grab the new fog light and pull it towards you this way under the hinge part. Layer it out.
Here we have our brand new fog light assembly from 1A Auto. This is for a '13 Camry and here's the factory one we just took out of the bumper. You can see they have the same four mounting spots. Turn ours around. It comes with an adjuster, just like that one, and we also supply the bulb. And a vent for any moisture to come out. If you need this part or any other part for your car, click on the link below and head over to 1aauto.com.
Now we're going to put the new fog light up in. Pull down a little bit and just screw it underneath. You're going to put those two tabs in on the inner edge. Line those up. You're going to take these two tabs and line up with these two holes, eyelet holes, and just fog light right up in place. Now I'm going to put the Phillips screw back in the mounting hole. Snug that right in. Put the shield part up underneath the bumper cover and line up the actual mounting screws all the way around.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
