2004 Pontiac Montana All Wheel Drive Rear Passenger Side Wheel Bearing & Axle Socket Kit TRQ BHA84972

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike from 1A Auto. I hope this helps, the video helps you out and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front hub on this 2000 Buick LeSabre, pretty much the same as any 2000, 2005 Buick LeSabre and obviously we sell new hubs at 1AAuto.com.Tools you'll need are Jack and Jack stands, 34, 19, 15 and 13mm Sockets. You'll need Ratchets and Extensions and you'll also need a Breaker Bar and possibly a Pipe for some extra leverage on some of those bolts and a large Flat Blade Screwdriver, a Hammer and Torque Wrench. On this LeSabre, you want to remove this center hub cap. Just pull firmly. If you don't have the benefit of air tools, you want to use a 34mm Socket and a big Breaker Bar, probably the pipe. With your vehicle on the ground, loosen up this center knot. Loosen up here first. You want to loosen your lug nuts with the wheel on the ground then raise and support the vehicle and then remove the lug nuts and wheel the rest of the way. I'll fast forward here as I use a 19mm Socket with an Impact Wrench and remove the lug nuts and the wheel and tire, and then just turn the suspension so that I can get a good look at the brakes. To get the brakes apart, first you're going to remove two 15mm bolts here and here. You should be able to use a 15mm Socket with a Ratchet and this should come apart with some force but it should come apart very easy.

I'll speed it up here as I loosen the top one and take both those bolts out and I'll show you them in a minute. The bolts are actually, the items that the calipers slide on as well so I'll show a little close up to you. These are slides taken apart. You want to note their condition. This probably should be just clean up and put a little grease on to them. I'll speed it up here again as I just remove, finish removing the upper bolt out of the top. With a large screwdriver, put it right in here and pry out and that actually forces the piston back into that actually forces the piston back into the caliper a little bit. You could see, I use a screwdriver pry out on the caliper a little bit and that loosens up so I can get the caliper up and off and then I just hang it up on the strut. I'll show you that right there. Now, your brake pads very easily. Just pry out. Remove these two bolts here. I needed my Socket again and a Ratchet. Use a Breaker Bar or a piece of pipe. A piece of pipe helps you get some extra leverage and just push nice and firm until you start to get them loose. I'll fast forward here as I use the Ratchet and pipe to loosen up the top one and then take both the bolts out. Now, your rotor comes right off. Here, I'm applying some penetrating oil to the center hub knot as well as the three knots that hold the hub to the steering knuckle. Here, I'm removing that nut with an Impact Wrench.

Again, if you don't have air tools, you'll want to loosen up this knot when your tire is still on and the vehicle is on the ground. You want to make sure that your axle is free from your hub. You're going to give a one good hit with a hammer. You don't want to be on it continuously with a hammer because you could damage your CV joints but one good hit and just watch the axle in relation to the hub, if it moves then your axle is free and is no problem. Just give it a good wrap and just watch. Like I said, the axle in relation to the hub and it moved so it's nice and free. I can actually move it just with my thumb. Now, three bolts hold the hub to the steering knuckle. You could see one down there and one up in there. Generally, you want to use 3/8s drive tools because they're a little narrower and they can get in here better. There's the bolt here, there's one down here and then over on the other side, there is a bolt right down in here. This is your ABS lead, you want to use a screwdriver, pry this clip away. Pull that off and then just push up on this clip here and disconnect it. I'm going to fast forward here as I take and loosen up those three bolts and you should be able to get them with a good sized 3/8s Ratchet. You want to just keep applying even pressure. Don't jerk the wrench or anything. Apply even pressure and they'll come loose and what I'm doing is actually turning the steering knuckle back and forth so I can easily get to all three of the bolts. Once you get up to this point, you need to push. I've got pushing it with my thumb on the axle and then pulling the center wire out. You want to take this off and put right there.

New hub available on 1AAuto.com, you want to put in there. You want the sensor kind of towards the rear towards where it goes in and this goes on so that this tab is in this position over here. Put it on and again, just reach through with your thumb, push on the axle so that you could push your sensor connector through. Pull that connector through this bracket up and on. I'm going to get that up on here. Pull this connector; pull this back and in there. Kind of a matter is getting the grooves all lined up and in. Tug on your ABS sensor a little bit, make sure it's through cleanly. Push that on, the bolt. These ones' the easiest lugs that put it through and start it into the hub. I'm going to speed it up again as I start all three bolts in. You want to make sure you start them all in first, then usually tighten up the rear one until it snug and then you tighten up the other two until they're snug. The last step of tightening is to torque them. Make sure the leads through correctly. Put right on to that bracket and then plug it in. I'm going tighten these bolts to 60 foot pounds, starting with this rear one. I'm going to reinstall this hub knot just preliminarily. Rotor goes back on. Before you put this caliper bracket back on, take a wire brush and make sure these all nice and clean. In particular, you're cleaning the grooves where the brake pads sit and slide.

This part goes between the rotor and the steering knuckle and that bolt goes to the steering knuckle first, then into the caliper bracket. Start my lower one. Now, start my upper one. I'll speed it up here as I just kind of preliminarily tighten those two bolts up. Now, we'll torque these to 80 foot pounds. Put it down and make sure your hose isn't twisted. You might want to pull these grommets in a little bit. Put your caliper down on, make that those aren't bunched up. Here are my sides, I cleaned them up, put a little light coated grease on them. That's a little one came out with this sleeve so I took that off, cleaned it all out, put a little bit of grease on the inside, on the outside of it. Put our brake pads back, it just kind of slides right in, the support one. Now, push down in a little bit diagonally. Top one back in first, start it a little bit and our bottom one. I'll fast forward again as I just kind of preliminarily tighten those bolts. I'll torque these for about 50 foot pounds. Again, apologize for the low volume, 50 foot pounds is what you want to torque those to. Okay, speed it up here as we put the wheel and tire back on and then just start the lug nuts by hand and then tighten them preliminarily with the Impact Wrench. Now, you want to torque the center nut to a 118 foot pounds. Torque your lug nuts to a 100 foot pounds using a start pattern. Okay, and we'll speed up the tape as we torque up the lug nuts. Anytime you take the brakes apart, make sure that you pump your pedal a whole bunch of times until it gets firm and then do test stops from five and 10 miles an hour, make sure the brakes are working correctly before you road test your vehicle.

We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.

Hi, I'm Mike Green. I am one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years' experience restoring and repairing cars and trucks like this, to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.

In this video, we will be replacing the hub on this '98 Pontiac Grand Prix. This hub fits a whole bunch of different GM cars, Buick Century, Regal, Cadillac Deville, Eldorado, Olds Mobile, Chevy Impala, Monte Carlo, Bonneville, Grand Prix, Montana Transport, Chevy Venture, all kinds of different stuff. Here's the list of tools you need for the Grand Prix. Really what you need is basically metric sockets from 13 mm up to 19 mm, plus the large hub nut, which is anywhere from 32 to 35 mm and then the rest of the stuff and plus throw in there some penetrating oil and a hammer and rubber mallet.

If your hub doesn't come apart as easily as the one that did in this video, you may need an axle or a gear puller. If you are working with hand tools, start on the ground. Remove your lug nut covers, and loosen up your lug nuts. I've got the benefit of air tools, so I'm going to raise and secure the car and remove the wheel and tire.

I've removed the wheel and turned the wheels all the way to the right here, so I can access the brake caliper bolts, which is the inside ones, one here and then this one here. Those bolts are 15 mm, I am going to remove them. You don't want the brake hose on the caliper to be stressed, so I just kind of took a wire tie and tied the caliper up here, then remove the brake disc. Be careful not to touch the disc and if you do touch it, just clean it off with some rubbing alcohol or mineral spirits when you put it back together.

There's three bolts that hold the hub on. I'll go in behind here and show them to you. There's one here, one up in the middle there, and then back here next to the, this is the steering tie rod, there is one right there. It'll help probably using a little penetrating oil, right on the opposite side. Now we are going to remove those bolts. They are 13 mm, 1/2 inch is a standard equivalent actually it fits, but I am using 3/8 drive tools, so I going to remove those three bolts and the reason you have to use this size tool, is to get in behind on this top one, you need smaller tools in order to get in there. Then you get a nice big handle to work it.

I'm just going to kind of fast forward through here. As I remove these three bolts and as you can tell, they take quite a bit of force to get going. It will help if you have a large breaker bar and then just swivel the steering back and forth to make it easy to get to the bolts on each side. Now I am going to remove the middle hub nut. I have impact tools, so that makes it really easy. If you don't have impact tools, what you want to do is, before you remove the brake caliper, have somebody hold the brakes and then with hand tools, you can pull that hub nut off. This hub nut is 35 mm, so you'll need a 35 mm socket.

Now you need to get the axle back out. You don't want to use a hammer and whack it hard, but what I'd do is just give it a check. If I see it move a little bit with the hammer, which it does, then I would have you break out the rubber mallet and whack away. Rubber mallet is not going to hurt the insides of your CV joint. Now I got the two lower bolts out and the top one is really loose, so now it is kind of a matter of not being nice. You got to pound on each side of the flange and the hub and slowly work the flange out of the steering knuckle.

I have the hub work loose, now I am just removing the top bolt the rest of the way. I just kind of left it in there in case I hit it hard enough and it just came flying out, just safety. Unplug the harness right here and flip up this with your thumb and pull it off. This is what you would rather not see happen. Basically, the hub has been in there so long, the back part stayed in the steering knuckle and this came apart, so what I am going to have to do is use some driving tools and just try and drive the rest of it out of the steering knuckle.

As you see, it turns out to be not much of a problem. You just beat on it with the punch and hammer and it pops out. Don't worry about damaging it or anything like that. I poked a few holes in it.

You just want to push the clip off of this bracket and the rest of that comes out. Push in on the axle and kind of up a little bit and your connector comes out.

Clean up some of the corrosion on here. I'm just gonna use some penetrating oil just to lubricate it. Now it's ready for the new one to go in. Okay, here's our new hub from 1A Auto and not only is it prettier and shinier, it's all in one piece, as it should be, as opposed to three separate pieces. If you kinda use your imagination here this is all the same, it's gonna bolt up the same and now we are gonna put it in and it's not going to make a big groaning grinding noise.

Okay so that ends this part of this video, part one. Check out our other videos to see the installation of the hub.

We hope this helps you out. Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.