Replaces
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our direct fit gas-charged shock absorbers help restore your vehicle's handling and ride quality to just like new.
Replacing struts used to require specialized tools to compress, remove, and transfer the old spring and mount. Our Pre-assembled, complete strut & spring assemblies come with all new parts and make the job much quicker and easier for the do-it-yourself mechanic.
Strut & spring assembly contains:
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the internet. Hi, I'm Mike from 1A Auto Parts. I hope this how to video helps you out and next time you need parts for your vehicle, think of 1aauto.com. Thanks.
In this video, we're going to show you how to replace the rear shocks on this 2003 Honda Odyssey; same for any 1999-2004. We show you the right hand or passenger side rear and the driver side or left hand rear is the same procedure. Tools you'll need are jack and jack stands to raise and support the car. You will also need a 17-mm socket and ratchet, as well as either a 19-mm socket or your lug wrench.
First, raise and support the vehicle then use a 19-mm socket and breaker bar. If you're just using hand tools, actually, you'll want to loosen the lug nuts when the wheel is on the ground and the vehicle is in park. Loosen the lug nuts first, then raise and support the vehicle. Remove the five lug nuts and remove the rear wheel. So you see my wrench is on the top of the shock absorber. Just spray some Anti-Seize or penetrating oil in there, and then do the same thing down here for the bottom. All right. Speed up here as we loosen that bolt. Don't take it out all the way yet. You can see it requires some force, but you should be able to do it with a regular ratchet handle. Again, fast forward as we loosen, and then we will remove this bolt.
Now back up to the top. Remove the top bolt the rest of the way. And now reverse the procedure, re-install. Use a hammer. Tap the bottom of the new shock onto the shock mount on the bottom. Now, use a jack to lift the suspension just a little bit to line up the top mounting hole and once you get it lined up, then slide the bolt in and start tightening it up. We'll fast forward. You may have to tap lightly on the bolt to get it going and then push firmly on it to start it and then tighten it up nice and tight. Then thread the bottom nut on and tighten that up as well. Both these should be around 65 to 70 foot pounds.
Now I'm going to fast forward to put the wheel back in place. Start all five lug nuts on by hand first and then just kind of preliminarily tighten them and then lower your vehicle to the ground. Now set your torque wrench to 90 to 100 foot lbs and torque the wheel using a star pattern. Whenever you have the brakes apart, just make sure that you pump the pedal a few times. Make sure it's nice and firm. And then before you road test your vehicle, just do test stops from 5 and 10 miles an hour just to make sure the brakes are working properly.
We hope this helps you out. Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the internet. Hi, I'm Mike from 1A Auto. I hope this how to video helps you out and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we're going to show you how to replace the front strut on this 2003 Honda Odyssey. Pretty much the same as any '99-'03. I'm sorry, '99-'04. We show you the passenger side front strut placement. Driver's side is the same. We do always recommend that you replace your struts in pairs, as well as you will need to take your vehicle for an alignment after this repair. You'll need a new set of struts from 1AAuto.com. You'll need a jack and jack stands, 8-22mm sockets. You'll need ratchets for those sockets with a breaker bar or a pipe for some extra leverage for some of the big ones, an 18mm wrench, some penetrating oil, and a flat blade screwdriver.
As you can see here, I've got the vehicle raised up and I'm removing the lug nuts with my impact wrench. If you don't have an impact wrench, you want to start with the vehicle on the ground, loosen the lug nuts with a 19mm socket and breaker bar or your tire iron. Then raise and support the vehicle and remove the lug nuts and wheel the rest of the way. You can see here I'm kicking the tire. That's basically just a way if your tire or wheel is a little bit frozen on because of the aluminum, just give it some good kicks and break it loose. Then you can remove the tire. We're going to start by putting some lubricant on the ends of the bolts so the nuts actually come off on the front and the back side. We've got an 18mm wrench and an 18mm socket for the top of the end link. The 18mm wrench goes on the back. Socket goes on the front. Then you just have to use your muscle to tear it apart. I'm just going to speed up here as we remove that nut the rest of the way. Now we can pull the end link out. There are a couple bolts on top that hold the break hose and the ABS sensor. Spray them down with some penetrating oil, as well as the two large bolts that hold the strut. The 10mm socket and ratchet to remove the upper, or the break hose. Then 8mm socket and ratchet or a wrench to remove the ABS sensor wire.
Next we're going to remove these two 22mm nuts so we can pull the bolts out of the strut and remove the bottom half of the strut. Most people have ratchets. If you need a little extra leverage, you can always put a pipe on the end of it and get yourself a whole lot more force on it. As you can see, it works. One step better than the ratchet would be a breaker bar. It is obviously a little longer so you don't need to add pipe to it usually. As you can see, it normally works too. Just see us cheat here as we get out the impact wrench and pull those nuts off the rest of the way. To get these two bolts out, you can see that they're already loose so we really just have to tap them out. Just going to fast forward here. You can just use your wrench, turn the bolts counterclockwise and pull on them and they'll come out, or just use some kind of punch or tool to knock them out from the other side.
Now you just basically need to wiggle them apart and then the bottom of the strut is detected. On the top you can see that there is three covers, and that's how you access the top bolts for the strut. First we'll pop the covers off. The three bolts on the top of the strut are 14mm so we'll drop a 14mm socket down there and... Fast forward as Jeremy removes two of the bolts. We're going to leave one on for right now. If you do drop one down in there you can actually just take that plastic cover, the cover that has the three holes in it, pull up on it, and you'll see me do it later, pull up on it and a couple clips come loose and you can reach underneath there and grab the nuts if you drop them. Now we'll loosen up the last nut and you see the strut start to drop down. As you can see, the new one looks a lot like the original one, except obviously brand new. It will look and fit and bolt in just like the original one did. You want to put the top in first. Make sure you put the ABS sensor wire in the right spot. That's going to go under the strut. While one person is lifting up, you can actually lift up this roof here. Grab your new bolts. Help guide it up in there. Turn it a little bit the other way. Guide it up in, and start your bolts.
I'm just going to fast forward as Jeremy reaches under that cover, puts on the rest of the bolts and then kind of preliminarily tightens them. If you didn't have a helper, what you could do from the last scene is put one of the lower bolts into the lower strut mount area and then just use a jack to jack up the suspension to help you guide the strut into place. Now we're going to torque these top three strut bolts to about 34 pounds. I'm just going to fast forward as we, as Jeremy tightens up the last two bolts, then puts that plastic cover back down in place. Make sure all the clips are secure, and then put the three little plastic covers that go over top of the bolt holes into place. We can basically align this by sticking something through the bolt holes. Now make sure the ABS wire is in the right spot and you should be able to get the knuckle into the middle of the strut. Fast forward here as Jeremy pushes those bolts through, puts the nuts on and just kind of preliminarily tightens them up.
You'll want to torque these bolts to between 115-120 pounds. Speed it up here as Jeremy bolts on some of the final components, the 8 and 10mm bolts that hold the ABS sensor and the break line, as well as a little bit later you'll see him put the strut, the stabilizer link strut back on. Obviously we're showing you the passenger side. You always want to replace these struts in pairs and as well have your vehicle aligned after you do this type of repair. Put your wheel back on and start all your lug nuts just by hand first, and then while the vehicle is still in the air just kind of preliminarily tighten them with your socket and ratchet or as I'm doing with my impact wrench. Again, use your torque wrench and you want to tighten your lug nuts between 95 and 100 foot pounds. Use a star pattern as you tighten.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
