Kit Includes: (1) Passenger Side Outer Tail Light (1) Driver Side Outer Tail Light
Quantity: 2 Piece
Specification
Side Location
Driver & Passenger Side
Location
Outer
Product Features
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Tail Light 1999-2004 Oldsmobile Alero
Created on:
Tools used
No Tools Needed
1. Removing the Taillight Assembly
Lift the panel along the trunk up and off.
Remove the cargo clip.
Pull back the insulation.
Remove the three thumb screws.
Pull the taillight assembly straight out.
Unclip the harness from the taillight.
Twist all of the sockets out.
To change a bulb pull it straight out and push the new bulb in.
2. Replacing the Taillight Assembly
Twist the sockets into the new taillight assembly.
Clip the harness back into place.
Line up the taillight and push it into place.
Replace the three thumb screws.
Replace the insulation and net clip.
Push the panel down into place.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video we show you how to service a taillight on this 2000 Oldsmobile Alero, same as a '99 - '04. No tools are necessary. We're going to show you both how to service the bulbs if you have a bulb out, and also how to replace the whole assembly if you have one that's been broken.
For these taillights, you're going to work in the trunk. This panel you want to lift up and off. As you can see, somebody must have gone sideways with it. They broke all the clips off. These just pull up and out. If you lift this panel straight up, it will come out correctly. Then inside, you have this cargo net. We take it off of there. You can pull this back. There are little thumb screws to remove. I'll fast forward through removing those thumb screws. There's three of them that hold the light and then the light pulls back. I will take that middle one which holds the cargo net and take that apart so I can get the net and the side panel back in easier. Take that out. If you're servicing your bulbs, two of them, the larger one have a little frontal tabs. You press the tab and it's turned counterclockwise. The bulb comes out. The smaller one turns counterclockwise and comes out. Take this harness right off.
Your new light from 1A Auto. It's just like the original. It's going right in just exactly the same. As far as these bulbs go, they just pull out and push back in. Make sure the little rubber gaskets stays with the socket. Clip the harness right on the same place that has the gaskets. The light fits in. Push those studs in. I'm going to speed it up again as I put those thumb screws back in. You want to put those in and tighten them up nice and firm. They don't have to be extremely tight. Once you get those tightened up, then put your panel back in place and the thumb screw that holds that in place and your net. This panel, just bring in. Press down.
We hope this helps you out, brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
LHT07390
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
does come with blubs?March 23, 2016
H A
10
No these will not come with bulbs, but you can reuse your originals.
March 23, 2016
Derek C
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Oldsmobile is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Oldsmobile or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.