Kit Includes: (2) Fog Lights (2) Headlights (2) Corner Lights
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Corner Light 2001-05 Ford Ranger
How to Replace Headlights 2001-11 Ford Ranger
How to Replace Headlights 1998-2011 Ford Ranger
How to Replace Headlight 2001-11 Ford Ranger
How to Replace Fog Lights 2004-05 Ford Ranger
Created on:
Tools used
6mm Socket
Ratchet
1. Removing the Headlight
Pull up the two headlight tabs
Pull the headlight forward
Pull off the headlight bulb connector
Twist out the signal light bulb
2. Removing the Parking Light
Remove the two 6mm bolts from the parking light
Pull the parking light off its pin
Twist out the parking light bulb
3. Installing the New Parking Light
Twist in the parking light bulb
Push the new parking light onto its clip
Insert the two 6mm bolts into the parking light
4. Reinstalling the Headlight
Twist the signal light bulb into the headlight
Connect the headlight wiring connector
Push the headlight into place using the adjuster bolts
Hold the headlight in place as you push in the two headlight tabs
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video we will replace the parking light on this 2004 Ford Ranger, the same as any '01 to '07 Ranger. You start out by, to get to the park lights, you remove the head lights. There are 2 tabs that you pull up on right back here. Once you have those tabs up, just pull your light forward. Here's the bulb. You can access the bulb easily. Pull this connector off. Then, your turn signal bulb, you twist, and it comes out, and your light is out.
Once you have your headlight out, remove those two 6 mm bolts. It has a little pin that holds it in right there. You can twist and remove that.
Here's our original light. Here's our new light from 1A Auto. You can see they're exactly the same. If you're looking to freshen your lights up, to freshen your truck up, it will do well, all of those scratches. Obviously, if you get in a little skirmish, with a rock, or a little bit of a fender bender, it takes out your marker light, this is a perfect replacement. All the mounting points are the same, and it's going to go in there exactly the same.
Obviously, to put it back on is the reversal of the procedure. Put your light in. Twist. Set it in. Put in the 6mm bolts.
Installing is the reverse of the procedure. Put your signal in first, turn and lock. Plug your light bulb in. Then carefully place it back in there. I'm kind of looking down to make sure all the adjusters are going to their holes properly. This middle one, here, is a little bit off. There we go. So, down there, just make sure that is all the way through. On this side, make sure that one there, and the one down below, which is hard to see. Just make sure those are all the way in. Push in real good. Push down on your tabs. You can see this one's not in very well. Pull back up. Push down. Now, it's in nice and secure.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Socket Extensions
5.5mm Socket
Ratchet
1. Removing the Headlight
Remove the three 5 1/2mm bolts from the headlight bracket
Remove the plastic cover from the top of the headlight
Lift up the two tabs to a balanced point
Pull the headlight out
Turn the base of the bulbs counterclockwise
2. Replacing the Headlight Bulbs
Lift the tabs and disconnect the wiring harnesses from the old bulbs
Remove the old bulbs
Insert the new bulbs
Connect the new bulb to the wiring harness
3. Installing the New Headlight
Turn the base of the new bulbs clockwise
Insert the headlight into place
Press the tabs down
Insert the plastic cover into place
Replace the 5 1/2mm bolts into the headlight bracket
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks!
In this video, we're going to be working with our 2001 Ford Ranger. We're going to show you how to remove and replace your headlight assembly, or you can follow these same steps to access the turn signal and headlight bulb if you need to change them. We're going to be working on the passenger's side, but this information is the same for the driver.
If you like this video, please click "Subscribe." We have a ton more information on this truck, as well as many other makes and models. If you need this part for your vehicle, you can follow the link down in the description over to 1AAuto.com.
Here are the items you'll need for this repair: 5.5mm, ratchet, and extensions.
Remove the three 5 1/2 millimeter bolts on the top cover for the headlight with a socket, ratchet, and extension. Then remove the plastic cover from the top of the headlight. There's a metal tab on the inside here under that cover. We'll lift up there. Don't lock it all the way up. You want to let it sit at that float point there. Get the one on the opposite side here. Same thing: lift up and hit that balance point. You might have to wiggle them a little if the headlight is not coming out smoothly.
Twist the sockets for the turn signal counterclockwise and the collar for the headlight spins off counterclockwise. We'll place our headlight assembly off to the side.
Now, if you're just in here to change the bulbs, from this point the headlight disconnects from this electrical connector. You want to lift up on those tabs. Pull the assembly out of the socket.
New bulb snaps in. Be sure that this collar sits between the socket and the bulb. Turn signal simply pulls straight out. Your new bulb pops straight in.
To give you a better idea of how these headlight retainers work, you'll see the hole here where our plastic retainer is going to slide in on the back of the headlight. This is with that slide in the floating position. If you pull too far up, the metal comes through the opening and will still hold the bottom of the retainer. Let's see: key hole, when you slide down, that thinner portion locks over the top. When we hit this nice middle point here is when our headlight comes out nice and smooth.
Install the sockets into your new headlight. Socket goes in, and a quarter turn clockwise locks it in place. The headlight pops in. The collar goes over the tabs and locks on clockwise.
Now, we'll line up these pins into the openings. Again, you might have to wiggle those slides a little to get them to go in. Once they're over, lock the tab back down into place and ensure your headlight is in straight and secure. Reinstall the plastic cover over the top of the headlight. Tighten it down with a socket, ratchet, and extension with your 5 1/2 millimeter screws.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
Tools used
Measuring Tape
Painter's Tape
Tools used
No Tools Needed
1. Remove the headlight assembly
Pull up on the two tabs above the headlight assembly
Pull out the headlight assembly.
Unplug the harness.
Replace the bulbs if that is all that is needed, otherwise replace the entire assembly.
2. Install headlight assembly
Adjust the adjustor bolts to match the old assembly.
Plug the bulbs and harness into the new headlight assembly
Put the headlight assembly into place.
Push down the tabs.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1aauto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you headlight removal and installation on this '04 Ford Ranger, pretty much the same for any '93 to present Ranger and no tools are necessary. Headlights on these Ford Rangers are really quite nicely designed and pretty easy. There are two tabs that you pull up on right back here. Once you have those tabs up, just pull your light forward. Now, here's the bulb. You can access the bulb easily. Pull this protector off and then your turn signal bulb, you twist, and it comes out, and your light is out. Obviously, you can service the bulbs.
The headlight bulb, you twist this, pull it out, and then you can pull the bulb out. Here's our original light, and here's the new light from 1A Auto. Now, obviously if your original light has been broken or something, you're going to want to replace it with a new one. You can also see, this truck doesn't have many miles on it, so the lens isn't too cloudy or faded, but if you drive your truck a lot of miles or in sandy conditions, these lenses can get pretty chipped up and clouded. A nice easy way to fix that is to just put a new set of lights in. You can see our lights are going to mount in the same. They have all the same connectors and everything so everything is going to go in just like the original.
One tip is before you put the new light in, just try and match it up with the distance. You can see that this adjuster is pretty close to the light there, so just preliminarily aim it. Take your new light and just try and get that just about the same distance. For now, obviously this light is fine, so we're going to put it back in the truck. Installing is just the reverse of the procedure. Put your signal in first, turn and lock, plug your light bulb in, and then carefully place it back in there.
I'm kind of looking down to make sure that all the adjusters are going into their holes properly. The lower one here is just a little bit off. There we go. Down there, just make sure that is all the way through. Then on this side, make sure that one there and the one down below, which is hard to see. Make sure those are all the way in. Push it really good. Push down on your tabs. You can see that mine's not in very well. Put it back up here. Push down and mount it nice and secure.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free, 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
8mm Socket
Ratchet
Needle nose pliers
11mm Socket
1. Removing the Fog Light
Remove the 8mm bolt from the fog light
Pull the locking washers off with needle nose pliers
Remove the two 11mm speed nuts from the fog light
Twist the bulb out of the fog light, avoiding touching the bulb
Pull the fog light out of the bumper from the back side
2. Installing the New Fog Light
Put the new fog light into place, hanging it on the studs
Tighten the speed nuts onto the fog light
Twist the bulb into the fog light
Insert the 8mm bolt into the fog light
Set the adjusting screw to the same length as on the old fog light
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be showing you how to replace the fog light on this 2004 Ford Ranger, same as any '04 or '05, and similar for other years of Ranger. You'll just need some basic tools, some various millimeter sockets and needle-nosed pliers.
All right, to do a fog light on a Ranger Edge here, you're going to need to remove this 8mm bolt right here, okay. This is a tire, so we're looking at the fender or the bumper. We're going to remove this 8mm bolt. Now, so viewing it from kind of the middle of the car in, you want to take a regular pair of needle-nosed pliers and there's these little locking washers here. Once you get them turning sometimes, if you work on it, you can probably save them, but most of the time you may just want to twist them off. You kind of break them. Then I'll get the other one too. Okay, and then these speed nuts are 11mm, and there's kind of a long stud, so put the socket on there.
Here's your bulb. If you're just looking to replace the bulb, obviously, you just pull it out, twist it and pull it out; it's a halogen bulb, so you don't want to touch it, if your bulb's still good. You don't want to get your finger oil on it. Once you have these nuts off from that bolt, then you just kind of pull from the outside, comes off, and there's your fog light out.
So here's our original fog light, and a new fog light from 1A Auto. You can see all the holes and everything are all the same. Your bulb's going to go in there all the same, and it's just going to fit. Obviously, if your fog light got broken by a rock or something this is what you need, or maybe you just want to freshen up the car. You can see our new one is quite a bit clearer and brighter than the old one. So, reinstallation is pretty quick. Put the fog light up in there, put it on those plastic studs, and push it onto the bumper tab there. Start the speed nuts, and put our 8mm bolt in. Actually, you put the bulb in, then the 8mm bolt. Then just one tip: If you put a new one in, there's a space here between here. This is the adjusting screw, and you can adjust it up and down, and there's a space between the light assembly and the bracket, and on your new light you want to just set that at the same as the old light, and that'll be a good preliminary aim.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Product Reviews
Loading reviews
5.00/ 5.01
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
2004 ford ranger edge
Robert
May 18, 2022
Perfect match & fits very wellheadlights & fog lights
Customer Q&A
Will these fit a 2004 mazda B3000 pickup?March 7, 2022
John D
10
Currently, we do not carry this part for your vehicle. We're always updating our inventory so please check back soon!
March 8, 2022
Emma F
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.