Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the lower front light. This is the side marker light, the signal light, as well as your daytime driving lights. We'll show you both changing the bulbs, as well as if you want to replace it with a whole new assembly from 1A Auto. If you go for it, a new set of lights on the front end of your truck will take miles off, make it look a whole lot better, and help you see better at night. You won't need any tools for this. You may want a flat blade screwdriver.
Open up the hood by pulling the lever here. Reach under the center of the hood, you'll see a little lever right here. Push it towards the center of the truck and lift up.
The headlights are pretty easy. There's actually a little lock bar right here. Pull it up out of the clip. You might have to work it back and forth as you pull it towards the center of the truck. This pulls right out, and then your headlight tilts back and out. Right in behind, your headlights are connected. You don't have to have the battery disconnected. As long as the truck's off, there's no power going through here. Just pull back on these tabs and push off the connectors, and your whole assembly comes out.
Now if you're just looking to change the amber signal bulb, it's right here. There's a little tab. Press down, twist counterclockwise, and that comes out. Twist back in to lock it. Do the same thing, here, with your driving light: on the little tab, push down, twist counterclockwise, and that can come out. I've pulled that out for right now.
If you want to remove the whole assembly, just push the little tab right here. Push this tab towards the outside of the truck. Most of the time I'm able to push this tab just with my fingers and pull the light out, but it's possible you may want to use a flat blade screwdriver, here, to help you push on the tab, and then even twist it a little bit to help pry that tab from the body of the truck. The whole thing comes out. Disconnect here. Your marker light is down here, just twist it counterclockwise, pull that out, and the whole marker comes out.
Just to show you, here, on these bulbs, I just pull right out of their sockets like that, and they go back in.
Reinstall the new light from 1A Auto. It's going to go in just like the original. Put your marker in first. Push through the signal bulb, and your other bulb. There's a tab right here on the inside, make sure it goes into the radiator support. Then just watch this tab go right in, and it snaps right in place.
f you had some damage or your lights are clouded or faded, the new light from 1A Auto is going to go in there just like the original. It plugs in. The bulbs plug in just like the originals. On the bottom, there are two tabs that go into slots here, so you kind of feed it in behind the grill, and peek back in there so you can see those tabs going into the right spots. Once they're in, then, line it up right here. Push it back in, put the pin in and through, and just push it through until it locks down in place again. Then, for the new light, peel off the plastic covering.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
One of the first things you need to do is pop your hood. Once you've done that, go ahead and grab on to this right here, flip it up, go ahead and draw it away. You might have to tilt it down to get it underneath there. Grab your headlamp assembly. Carefully pull it away. And then if you were to look at the back, you're going to see the pigtails for the headlamps. Go ahead and grab that. Turn it counterclockwise. Carefully remove it. Do the same to the other one.
Now that that headlamp is out of the way, we have a clear view of what's going on down here. If you were to look right where my screwdriver is, there's a little tab. You're going to press that towards the outer portion of the fender, and then draw the assembly away. Maybe I'll try it once just so you can see. Press it. Draw it away. There we are. Go ahead and grab onto these. If you squeeze this tab right here, it should unlock, and then you can twist it. Do the same for this one, and then, of course, the marker at the end, you just twist that.
So, now we're going to get our new lamp assembly back in. Go ahead and grab this. Go ahead and turn it in. Lock it. Give it a nice wiggle. Let's get our directional bulb in here. Go ahead and twist it. Lock it in. This one, little less reach here. Lock that one in as well. Perfect. Now, when you go to install this, on the inner portion, you're going to see there's a little hookie-do. That needs to slide in over there. So, we'll go ahead and get the hookie-do into where it's supposed to sit. And then if you look right here, we're going to line this up and then carefully press it in. Make sure it's locked in. This feels great.
Now, it's going to be time to install the headlamp. Go ahead and grab these bulbs. Start them. Line them up. Twist it. Lock it in. Do the same to the other. Okay. Now we're just going to come around the backside of the grille here just like this. Come up and over that, and then rest this right in. This should line up right along there, and then this should line up right down here. Now we're going to get our pin in here. It's a good idea to just clean it up if you can get off any other rust that might be on it. Get it close to where I want it. Now I'm just going to bring the headlamp over. Squeeze this in. Bring it right on through. Line it up with this one. Flip this over. All right. So, now it's going to be time to test these lights. We've got our headlights on. We've got some high beams. Check that directional. Make sure it works. Perfect.
Tools used
