Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Steering & Suspension Kits
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our direct fit gas-charged strut assemblies help to restore your vehicle’s handling and ride quality to just like new.
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a front stabilizer link on this 2007 Pontiac G6. It's the same as any 2005 to 2010 G6, as well as the Saturn Aura. Not a difficult procedure. You will need jack and jack stands, and you'll want to jack up both front wheels off the ground and support it with jack stands. Then you'll need a lug wrench or a 19mm socket with a ratchet, maybe even a breaker bar and a pipe for some extra leverage. Then, after that, you'll just need two 18mm wrenches, one of those 18mm will have to have an open end.
Start out by using just a socket to loosen the lug nut covers, or the wheel cover as in this case. We're going to use impact or air tools sometimes. If you don't have the benefit of air tools, just start with the vehicle on the ground, loosen the lug nuts, then raise and secure the vehicle, and move the lug nuts from the wheel and tire.
Use an 18mm wrench to grab on to the nuts, part of the stud of the stabilizer link, and then use an 18mm socket, loosen up the nut, and then it comes off. Here's the fun part of the repair. You pull that down out of the way, and you can see the other end of the link right there. Put the 18mm wrench on the nut that's in the shaft, just like before. Then, there's not really enough room to get a ratchet back in there, so you basically just have to take a wrench and slowly, carefully, one eighth of a turn at a time, and I'll fast-forward the video as we do that.
Then, just reinstall the link as you took it apart. Go ahead and speed up as we tighten up that lower nut, and like I said before: it's not all that difficult; it just takes quite a bit of time because you can't move that nut too far each time.
Bring the sway bar link back into place, and should you possibly feel the need to replace those sway bar links, at 1AAuto.com, we sell those as well. But then use a 18mm wrench and an 18mm socket and ratchet to tighten up that bolt. And that bolt should be tightened somewhere around 70 to 75 foot-pounds. Put the bracket that holds your brake hose back into place, and start the 10mm bolt on and tighten it up.
Reinstall the wheel. Put the lug nuts on by hand first just to make sure you don't cross thread them, then tighten them preliminarily. Put the vehicle on the ground, torque the lug nuts to 100 foot pounds using a star pattern. Now, reinstall your hubcap and we're going to do that with that 19mm socket. I'm just going to screw them in by hand. Also, we want to make sure you line up the valve stem with the notch in the hubcap for the valve stem. I'll go ahead and fast-forward through that.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a stabilizer link on this Chevy Cobalt, pretty much the same for any Cobalt as well as the Pontiac G5. The stabilizer link makes kind of a rattling or thunking noise when you go over a bump. A good indicator that it's your stabilizer link is if you're getting that rattling noise and then, you turn your vehicle, you take a curve, and the rattling noise goes away; that usually means it's a pretty good indicator that it's that stabilizer link that's bad. The tools you'll need are jack and jack stands, 18mm and 19mm sockets with a ratchet. You'll need some pipe for some extra leverage as well as a breaker bar and 15mm and 18mm wrenches. It's pretty much a bolt-on, bolt-off, but sometimes these nuts are really difficult to remove, so there's some techniques in this video that will help you out.
Use a 19mm socket or lug wrench and remove the lug caps and the wheel cover. If you don't have access to air tools, you'll want to start with the vehicle on the ground. Loosen the lug nuts first and then raise the vehicle and remove the lug nuts and the wheel and tire.
Now, use an 18mm wrench and you can grab on the back side there and then use an 18mm socket and ratchet and remove that nut. Use a little bit of penetrating oil just to help get that nut off easier. Now, I'm using my 18mm socket with the ratchet and a piece of pipe. You can use pipe or if you have a breaker bar. You just need some extra leverage. Get that bolt to move some, and then, actually, grab on to the wrench, hold the wrench, and start it loosened and then you can do it by hand the rest of the way. Once you remove that nut, then you can just knock out or remove the top of that stabilizer link. Now, here what I've done is I've supported the bottom of the suspension. What that allows, is it allows me to get a breaker bar onto that bottom bolt and first you can pull the breaker bar, which breaks the nut and the bolt, breaks it free. Then you see with the breaker bar, I start loosening up that nut. You're just going to have to work at it, it's kind of tough to get apart. Just go at it for a while and the nut eventually comes off. Actually, after you get it loosened somewhat, you can get your ratchet on there, and then, use the ratchet to get the nut the rest of the way off. Once you have that off, you can just reach up in there and pull the stabilizer link out.
So, the 1A strut is pretty much the same thing. It has a little different sizes. It's a 19mm nut and a 15mm stud. We'll fast forward through this part. You just take that stabilizer link and put it back into the new strut and put the nut on, and tighten the nut up. You want to get it nice and tight. If you were to torque it, I guess it would be probably about 45 to 50 foot-pounds. Also, if you have ABS brakes, you want to reconnect any clips or anything that holds the wiring to the strut.
Reinstall the tire. You want to put the lug nuts on by hand first and then just kind of preliminarily tighten them, and torque them when the vehicle is back down on the ground.
We'll tighten and torque these to 20 foot-pounds. We'll speed up here as I do that. On the inside one you can't really get a torque wrench on it, so I just used a small combination wrench and got it nice and tight. 20 foot-pounds is not that tight. You don't want to over-tighten them because you could strip them and these are not bolts that you want to strip. Now torque your lug nuts to 100 foot pounds each and then replace either your wheel cover or the wheel caps and the retainers
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Okay, friends. Before we get started, the first thing that I want to mention is you want to be safe. So, have hand protection and eye protection. The next thing we're going to talk about is safely raising and supporting the vehicle so the suspension is hanging. So, come right underneath here. This is where you're going to support the vehicle in the front. Now, with the front of the vehicle safely raised and supported, we're going to remove all five of our 19-millimeter lug nuts. Remove your wheel.
First, what I like to do is remove the sway bar link from the front strut. So, I'm going to use some locking pliers, come from the backside right here and just try to hold onto the stud so it can't spin. All right. Let's get this off of here. Okay. Now that we have the sway bar link off of here, we need to go over to the other side of the vehicle and remove the sway bar link from the strut as well. That way there, we can move the sway bar up and down as needed to get to that mounting nut. There it is, friends.
Okay, friends. Now it's going to be time to put it in our brand new front sway bar link. One thing I like to mention is it's always a great idea to do these as a pair. And if that's the case, now's the time to do it. So, let's go ahead and put this in starting with the bottom. Now, I'm going to use my 17-millimeter wrench to hold the stud from spinning, and then we'll snug it up. If you were to try to torque this you'd want to torque it to 48 foot-pounds. It's going to be very difficult to torque because as you try to twist, it's going to want to lift up on the bar. If you try to put the bar inside here, obviously, you're not gonna be able to get to it. So, 48 foot-pounds, if you can do it. Let's get the sway bar link connected to the strut. Let's torque this to 48 foot-pounds. We're going to go ahead and put the wheel on here. We'll start all the lug nuts, we'll snug them up and then we'll torque them to 100 foot-pounds. Torqued.
Tools used
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
In this video, we're going to show you how to replace a front stabilizer link. The symptom of a bad stabilizer link is if you're hearing a clunking in the front of your car, but when you go around a curve, either left or right, the clunking seems to go away. That's usually a sign that your stabilizer link is starting to loosen up. Tools you'll need are 8mm to 19mm wrenches as well as a hammer.
Turn your wheel all the way to one side or the other. Then you can reach in behind and you can see it here. This is the top of your link. You can reach in behind and grab that with your hand and shake it back and forth and if you can duplicate that clanking or rattling sound then that's what you need to replace.
Start out by using a 19mm socket or a wrench and loosen the plastic covers and then remove the wheel cover. If you don't have the benefit of air tools, you'll want to loosen the lug nuts up while it's on the ground, then raise and support your vehicle and then remove the lug nuts and the wheel.
Right here is our stabilizer link. Use a little bit of penetrating oil on the upper and lower, let that sit for awhile. We've got an 18mm wrench on the bolt and 8mm wrench on the end of the shaft there. It looks like it actually coming loose, there goes that bolt. Get that started. Put this on there and I'm going to put this one on down there and same thing. Here's a close up look. I've got the 18mm wrench on there. The 8mm wrench is just holding that stud in place and I just keep flipping back and forth with the larger wrench, grabbing onto the nut and removing it. I'm just going to speed up the tape here. It takes a little while to get these things apart. It's a tedious task of getting the wrenches in there, holding it with the smaller wrench and then using the small one and then just angling the larger wrench in there as best you can. Eventually it comes apart.
Here's a new link from 1A Auto. Iit's a little bit different but it actually makes it easier to install. You'll need a 15mm wrench to hold this on that side and then a 19mm socket and ratchet to put the bolt on. We're going to put down in. It mounts in just like your original. Start the locking bolt on here and we'll start the locking bolt down here. Up top, I put my 15mm wrench through from the backside and then a 19mm socket and ratchet. I'll just speed it up as I tighten it up with the ratchet and you want to get it nice and tight and probably 40 to 45 foot-pounds. Then continuing on down to the lower, it's the same as taking it apart. You really can't get a wrench in there or a ratchet in there so you just have to use a wrench. I used the 15mm wrench to hold the stud and then a 19mm wrench to tighten up the nut and it just takes a little while and, then, again, tighten it up between 40 to 45 foot-pounds.
Once you have the wheel back in place then you put the lug nuts on by hand and I just use my impact wrench to just tighten them preliminarily. Now with the vehicle on the ground, torque the lug nuts to 100 foot-pounds using a star pattern. Now put your wheel cover back on, there's a hole for the valve stem then use a socket to tighten up the retainers.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Tools used
Tools used
Tools used
Tools used
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Steering & Suspension Kits