Replaces
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the headlights, as well as service the bulbs on this 2003 Mercury Mountaineer. We show you on the passenger side, but the driver side is a similar procedure. The items that you'll need include a new headlight from 1AAuto.com and a flat blade screwdriver.
Start off by pulling on this lever to open your hood. Then push this yellow tab over and lift the hood up. Then your headlight is held in with these two clips. You pull the clip up and out. Then do the same thing with this one. You need to try and pull the top out some first, but then you do have to get the bottom to come out at the same time.
I'm actually holding in at top and pushing out down here. It gets the whole headlight going. The same thing over here. I'm actually twisting down on the headlight like that so the whole thing comes forward.
To service the bulbs: this one here you turn counterclockwise. Pull it out, the bulb pulls free, and back in clockwise to lock. Then the headlight is right in here. Again, counterclockwise, there's the headlight. Pull and it comes off. There's a ring inside here, so again you turn counterclockwise, and then the bulb and ring comes out.
Take your new bulb and put the ring on. This tab for the harness will face up. I'm just going to pull the harness out of the way a little bit. Put the bulb in and make sure the bulb is seated then. Turn the ring clockwise to lock it. Make sure the bulb is firm and in place, and then reconnect your harness and put your cover back on.
Now, back here is the harness for your headlight and you want to pry that red clip back. Then push the tab underneath where the clip was. And while pushing the tab you want to pull on the harness to disconnect it. The easiest way to do this is to use the flat blade screwdriver to push the tab in while you're pulling back and it unclips. You just have to feed it through here, the hole right here. You will have to lift up the air intake box a little bit to get it out. Now your headlight's free.
On the driver's side, take your screwdriver, and you pry up on this little tab which disconnects that, and then you can get to this tab easy to disconnect it, and that's really the only difference. On the left is the old headlight; on the right is the new one from 1A Auto. You can see they're identical, and they'll fit exactly the same.
Feed that in, and you can reach in and grab the air intake box and move it out of the way. This way is to put the outside in first a little bit and work the inside in. Just check all of your wires and make sure nothing's getting pinched. You do have to work it by the grille, and usually just a light tap. The gaskets and stuff are a little tighter, so just give it a little push.
Just to give you an idea of how much newer your vehicle will look with new headlights, I'm going to show you some pictures. Here are the old, original headlights, and here are the new headlights from 1A Auto. You can see it makes the vehicle look newer; again, old headlights and new headlights.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
