Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Headlight 2004-06 Chrysler Sebring
Created on:
Tools used
Flat Blade Screwdriver
8mm Socket
Ratchet
1. Removing the Headlight
Remove the two 8mm bolts from the headlight bracket
Pull the headlight out
Disconnect the two headlight wiring harnesses
2. Replacing the Headlight Bulbs
This step is only necessary if you are replacing the headlight bulbs
Twist off the locking boot
Twist the bulb socket counterclockwise out of the light
Pull the bulb off of the socket
Push on the new bulb
Twist the bulb clockwise into the light
3. Installing the New Headlight
Reconnect the wiring harness to the headlight
Line up the bolt holes on the headlight bracket to the bolt holes on the vehicle
Replace the 8mm bolts into the headlight bracket
Move the headlight screw clockwise or counterclockwise to raise or lower the light beam
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace the headlights or service the bulbs in the headlights in this 2004 Chrysler Sebring. It's a sedan. It's pretty much the same operation for the convertible as well. It's applicable for model years 2004 through 2006. The items that you'll need are a new set of headlights from 1A Auto, an 8mm socket and ratchet, and a small flat blade screwdriver.
Maybe you're looking to change the bulbs, or maybe you want to put a new set of headlights in because yours are clouded, dull, and faded like on this car. You can see a new set of headlights from 1AAuto.com clears things up. If you're having trouble seeing at night, or you just want your car to look a little better, a new set of headlights from 1AAuto.com will help you out.
Locate the two 8mm bolts that hold the headlight in place right there and towards the corner. Using my 8mm socket and ratchet to remove those bolts I'll go ahead and fast-forward as I do that. Take the headlight and pull it out. I need to wiggle it a little bit. Push down and then pull out.
Go ahead and zoom in on the two connectors in the back. Right there I'm using a small flat blade screwdriver to pry up and then pull out on that socket. On the other one you're going to find a little maroon clip. You're going to need to use that flat blade screwdriver again. Pry that out, and then with your finger, press in on the tab and disconnect it. All right.
If you're just looking to service the headlight bulbs, that's a twist type socket and the bulb just pulls straight out and the bulb just gets pushed right back in. As for the main headlight beam, it's got a little circular disc that goes around it and holds it in place. Once you get that out the bulb, assembly, and socket as you can see they're all one piece.
Going back in you want to line up tabs on the socket and with the housing, and then put the circular locking collar back on. With this bulb, again, twist the socket and pull the bulb out. The bulb goes back in straight and then twists in.
Now, going in with the headlight, whether you're replacing it with a new one from 1A Auto, or putting it back in after servicing the bulbs, you're going to want to connect your two connectors that you took apart, and then slide it in place and make sure that the holes at the top where the two mounting bolts line up with the front end there. Drop your long bolt in, on the end board side, and your shorten bolt goes back over back by the fender. I'm going to go ahead and fast-forward as I tighten those up. To align your headlights, inside they're clockwise or counter clockwise on that screw to raise them or lower them.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
CS231-B001R
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chrysler is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Chrysler or FCA US LLC.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.