Replaces
Part Details
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com. Your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike from 1A Auto. I hope this how to video helps you out and the next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, I'm going to show how to replace a side view mirror on this 2008 Toyota Tacoma. It's not a hard task. The tools you'll need are a small flat-blade screwdriver, a Phillips screwdriver, and a 10mm socket with a ratchet.
To take the door apart, you start here. Use a small screwdriver, reach in, pull that out. There's a Phillips screw in there. Same thing here. Small Phillips on that door, a Phillips screw in there. This clip right here, push the center in and then the clip comes out and then this panel here. Just put your hands in behind and it pops off. Fast forward as I remove those two Phillips screws. You'll also want to come up under here, lift it up with your fingernails a little bit with a small screwdriver again, carefully pull that out and forward. On the side here, there's a little tab. You push the tab in and you pull. Now, there's kind of a locking collar. Gently kind of work out the screwdriver in there and pull that locking collar back and the locking collar comes off. Then that disconnects. Pull this collar all the way back until it clicks. Put that there. Then just use your fingers, work them in behind the door panel, pull firmly and there's a series of clips. Right around this edge. Once the clips are off the door panel comes right off.
Okay, right here is where the mirror connects in. You should press this tab at the top, disconnect and then there's three 10mm nuts right up here to remove. Use the 10mm socket with a ratchet and extension to remove those three bolts. Okay and I'll speed it up as I remove those bolts. Your mirror from 1AAuto. See, it's all the same. It's going to mount in there like the original, put the harness through. Remove the shipping protectors first, put the harness through and put it in place. Put the nuts right into the socket and just put them on. Speed up here again as I start the other two nuts on and tighten them up and you want to tighten these up nice and firm, don't over tighten though.
Okay, we're going to replace your door panel, pretty easy task. Make sure the harness comes through, put it up and on to the window sill, kind of look back here and peek in and see your pins, make sure they're going in correctly. Let's put that in here. We will push this back through so the lock is sticking up and put it in, push it to lock it. Speed this up as I put the two screws back in. The black one goes in behind the door panel and then the silver or natural colored one goes in behind the door pull. Put the trap doors back in place. Again, make sure that this locking collar is pulled all the way back and let's see here, put it this way. You put the back in first.
We hope this helps you out. Brought to you by www.1AAuto.com. Your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
