Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Part Details
Product Features
TRQ drivetrain kits are manufactured using premium raw materials to restore original performance. Each TRQ drivetrain component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the service life of your drivetrain, TRQ recommends replacing wheel hubs, bearings, and constant velocity (CV) drive axles at the same time to ensure even wear of components and improved ride comfort. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems. If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.
What are Tapered Bearings and Why Use Them? Tapered bearings use rollers shaped like flat-topped cones and two races angled from the outside in of the bearing. This angle makes the bearing better at handling forces exerted on the bearing during cornering (known as axial load) in trucks and large cars. Your model came from the factory with tapered bearings. Roller ball bearings work well for smaller cars, but replacing a tapered bearing with a roller ball bearing increases wear and failure.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi everyone. Sue here at 1A Auto, and today we're gonna talk bearings. The difference between a roller bearing and a ball bearing type.
While both a roller bearing and tapered bearings work in the same manner. Tapered bearings use tapered rollers shaped like flat topped cones and two races angled from the outside to the inside of the bearing. The rollers have a large contact area which is what makes them better than roller bearings at handling forces exerted on the bearing during cornering in trucks and large cars.
For applications that require it, the TRQ brand offers tapered roller bearing style wheel bearings that match OEM specifications where other brands do not.
Roller ball bearings work well for small cars but replacing a tapered bearing with a roller ball bearing will result in increasing wear and faster failure.
So now that you know all parts aren't created equal, you can purchase your TRQ bearing at 1aauto.com.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1AAuto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly; that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the front hub on this 2004 Dodge Ram. This is a four-wheel drive truck, same as most 02 to 08 vehicles this generation. Tools you'll need: Various both standard and metric sockets, ratchet, breaker bar, and a pipe for some leverage, (the bolts for the hub are quite tight usually), sledge hammer if you have some problem with your rotors, a large screwdriver, small pry bar, wire brush, large C-clamp, penetrating oil, jack and jack stands, and a torque wrench.
First you want to remove your wheel. If you're just using hand tools, start with the vehicle on the ground, loosen the lug nuts first, then raise it, secure it with jack stands and then remove the wheel. I've got air tools; I'm going to use them. These are either 7/8 or 22 millimeter; both will work. The next step, you may want to loosen your brake fluid cap a little. Okay, in the interest of keeping this video a little bit on the short side, I'm going to just kind of go through taking the brakes apart in 3x speed. You can probably gain enough here if you don't quite know how to get them apart or if you want to see this part of the video in real time, just check out our other videos for the Dodge Ram front brakes. Again, like I said, you can probably get enough to understand how to get the brakes apart just from this. Enjoy it even though it's a little quicker and then we'll get to the hub.
Now you're going to want to remove the axle. You want to remove the hub nut, which is a 35-millimeter bolt. If you're using hand tools, you will need to do this before you take the tire off. Lift the car up, take the center cap off, take the lug nuts off, take the center cap off, put the lug nuts back on, put the car back down, and then while it's on the ground use your hand tools to loosen up the nut. Then you can lift the car up. I'm just going to use my impact wrench and it helps me to zip the nut right off.
Now you want to separate the axle from the hub. You just want to use a hammer and give it one good hit. That'll tell you if the axle is free from the hub. You just hit it once and watch it really close and the axle should go right in. You won't need an axle pole or anything if that happens. You see I hit it and the axle goes in so I'm all set. Now what you want to do is get a pry bar and go way up like that. Pull your axle right off like that and your axle's out. Okay, now with the axle out there's three 18-millimeter bolts. You see one right down there, one up here, and there's one over here you can barely see. Before you actually take those bolts out, you want to disconnect your ABS sensor if you're vehicle has ABS. The connection is up there. Pull the clip out of the fender. There's a little tab that you have to press with your thumb and then disconnect it and pull it free from all the clamps that hold it to the brake hose and stuff.
We are going to use our 18-millimeter socket. Okay. Actually I'm going to loosen this. Again, be controlled with your pole. Use my pipe here. More leverage. Okay, these bolts are very tight. They also have a Loctite on them so just the combination of your 18-millimeter socket, your ratchet handle or a breaker bar, and a piece of pipe for some leverage and can get them loose. Once you have the bolts out you can actually cut them out pretty easy. Okay, wire brush. Clean everything up here a little bit. You want to feed your harness through and then the harness up, over like that, put your hub in. Prepare your bolts. Feed it through the top hole and do your best. Get the backing complete on there and then start into the hub.
Just make sure our harness is out of the way. I'm just going to use my impact wrench and just tighten this top one up a little bit. I'm not going to tighten it up. I'm just going to get it in there. Make sure it's nice and secure. Okay, I'm going to start my other two bolts and this should still be loose and moving around. I'm just going to fast forward here as I start the other two bolts and then I'll hook up my harness. Make sure you put it back into all the little grommets and clips that hold it in place so it doesn't chafe against anything. Then reconnect it and then I'll preliminarily tighten up all the bolts. The next thing you see me doing is torquing the bolts.
Now I'm going to use the torque wrench to get the top one. For the top one if you use a nice, long extension like that, loop it through from the back. Torque them to 100 foot pounds. Okay, we'll just fast forward again as I torque up the other two bolts. Now we're just going to take our axle. Put it right up in here, feed it into the hub. Turn it a little bit so you know where to push it with the hub. Push it right in. Now I'm going to take my hub nut and using my impact wrench just to get it on there, not really to tighten all the way up yet. Okay, now I'm going to grab hold of my CV joint on the inside. You go up on the top, pull your joint in as much as you can. Going on to the axle and then push it all the way on. Make sure it fits on there.
Okay, just in the interest of making this video a little bit on the shorter side, I'm just going to fast forward through putting your brakes back together. If you'd like to see this video or this part of the video in regular speed just check out our other videos for the Dodge Ram front brakes and you can see this whole part of the repair being done in regular speed. Now with everything back together, put your wheel back on. Don't put the center cap back on. Thread your lug nuts on there, and then just preliminarily tighten them up and then lower your vehicle down. Your hub nut, 185 foot pounds; my poor torque wrench only goes up to 150, so there's 150 and 25. Okay now raise the vehicle back up, take the lug nuts off, put the center cap back on, and preliminarily tighten up the lug nuts. Let the vehicle back down and torque the lug nuts to a 120 foot pounds using a star pattern. Very important, you've had your brakes apart so make sure before you drive the vehicle, pump your brakes a bunch of times, make sure the brakes are working correctly.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free 888-844-3393. We're the company that serves you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to do the wheel bearing and hub assembly on this Dodge Ram. This one's a 2008, but the procedure's pretty much the same for 2006 to 2008.
You'll need a new assembly from 1AAuto.com. 18 to 35 mm sockets with a ratchet and extensions, breaker bar, hooked pick, bungee cord or mechanic's wire, a pry bar, hammer, flat blade screwdriver, a file, torque wrench, and a jack and jack stands.
With the vehicle on the ground, using the 22 millimeter socket and breaker bar, break the lug nuts for your wheel loose. These chrome lug nuts tend to be swollen, so make sure your socket's on there good. Using the small pick, remove the center cap from the wheel. Using a 35 millimeter socket and a breaker bar, crack the axle nut loose. Raise and support your vehicle. Finish removing the lug nuts. Remove the wheel and tire from the hub.
Remove the two 21 millimeter bolts securing the caliper bracket to the spindle. Be sure to crack both of these loose before removing them. If they are removed fully one at a time, the caliper can twist and cause the flex hose on the brake line to tear. Be sure to support the assembly while you remove the last bolt. Remove the entire caliper and carrier assembly. Using a bungee cord secure it out of the way by hanging it off of the frame. Remove the rotor from the hub.
Brace the hub with a pry bar and finish removing your axle nut. Using a hammer, tap the end of the axle to push it out of the hub. Remove the nut for the tire rod. Take a 21 millimeter socket and ratchet. You want to leave the nut on a few threads so that it's flush with the bottom of the stud. Carefully tap up with a hammer. Remove the nut. Remove the tie rod from the control arm. Remove the 22 millimeter nut connecting the upper ball joint to the spindle.
Tap the front of the knuckle right where the ball joint comes through with a hammer to release it, careful not to hit it too hard because this is aluminum and it could crack. Once it's loosened up, you may have to hit the bottom of the control arm to release the joint from the knuckle. Using a flat blade screwdriver, release the tab on the connector for the ABS sensor. Push down and release the connector. Release it from the clamps under the control arm.
Pull down on the spindle or push up on the upper control arm to separate them and remove the axle shaft from the wheel bearing. Move the axle shaft so it's out of the way.
Remove the ABS sensor from the retainer on the spindle and allow it to hang off to the side. Using an 18 mm socket and a breaker bar, break the three 18mm bolts holding the hub in. Finish removing them with a ratchet. With the hub unbolted, use a hammer to hit the back of the hub and knock it out of the spindle. Be careful not to hit the dust shield in the process. Separate the wiring from the dust shield.
Here we have our old part that we removed from the truck and our new part from 1AAuto. As you can see, we have the same bolt pattern. Comes with new studs. We have the same splines where our CV axle's going to go in. We have the same ABS sensor, same wiring harness, and the same three bolt pattern to bolt into our spindle.
Using a file, clean the surface—both where the hub mounts to the face of the spindle and where it sits inside the bore of the spindle. Be sure that the spindle is free of burrs, corrosion, or anything else that's going to impede the hub seating into the spindle properly. Once the surface is free and clear of debris and dirt as well as burrs and any raised scoring, we can install our new wheel hub assembly.
Send your ABS wiring back through the dust shield. Be sure that the sensor lines up with the slot in the dust shield. If necessary, it is okay to line up the splines in the CV axle for now. Always start the hub in, start a bolt by hand, pop the axle out of the hub once we know it's aligned where we want it. Start our last bolt. We'll tighten these bolts down with an 18 mm socket and ratchet. Torque the bolts to 120 foot-pounds.
Line up and install the spines of your axle into the hub. Start your axle nut on as far as it'll go. Lift up on the upper control arm, slide the upper ball joint into the spindle. Pull down until you're able to get the nut started onto the threads. Tighten it down with a 22 millimeter socket and ratchet. Torque the upper ball joint to 40 foot-pounds. Add an additional 90 degrees.
Reinstall the tie rod into the spindle. Start the nut. Tighten it with a 21 millimeter socket and ratchet. Torque the tie rod to 45 foot-pounds. Reinstall the harness into the keepers and the bottom of the control arm. Reinstall the connector.
Push down on the safety tab. Reinstall the rotor onto the hub. Make sure that you don't twist the line on your brake hose. Reinstall the caliper carrier assembly onto the rotor. Start the bolts on the back side. Tighten the bolts down with a 21 millimeter socket and ratchet. Torque the caliper bolts to 130 foot-pounds.
Reinstall your wheel and tire onto the vehicle. Start the lug nuts with a 22 millimeter socket. Get all the lug nuts as tight as you can in the air and lower the vehicle. After tightening your axle nut torque it to 185 foot-pounds. Pop the center cap back into place. Torque your lug nuts to 135 foot-pounds in a cross pattern.
Thanks for tuning in. We hope this video helped you out. Next time you need parts for your car, please visit 1AAuto.com. Also check out our other helpful how-to and diagnosis videos.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
If your vehicle isn't listed, search Steering & Suspension Kits
If your vehicle isn't listed, search Steering & Suspension Kits