Kit Includes: (1) Mirror Cap (1) Driver Side Mirror
Cover Color: Black
Cover Finish: Smooth
Housing Color: Black
Manual Remote Control: No
Adjustment Type: Electric
Paint to Match: Yes
Specification
Side Location
Driver Side
Trim
SR5
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Direct Bolt-on Replacement: No modifications or special tools required
Complete Assembly: includes same mirror glass, housing, bracket and technology as the original unit
DOT Certified: Built to the highest quality standards
FMVSS-111 Compliant: Validated to be a dealership alternative
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Product Wiring Guide - Power Folding Mirror 2007-16 Toyota Tundra Sequoia
Created on:
Tools used
Gloves
1. Power Fold Feature Connections Explained
Take a red wire from the module
Strip the end and insert it into a butt connector leading to the add a fuse circuit
Remove a factory 5 amp fuse (such as the cigarette lighter light)
Attach the black wire/ground to a rust-free clean bolt on bare metal underneath the dash
Connect the green connector to the switch
If you do not have factory power fold, peel the backing from the base plate on the mirror
Pull out the white and yellow connector that connects to the factory harness
Disconnect the white and yellow connector from blue and purple connectors
Run the white and yellow connector through the opening in the shield
Connect the white and yellow connector to the small powerfold feature harness
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.
Here we have our upgraded tow mirror for the 2008 to '16 Toyota Sequoias, as well as the 2007 to 2016 Toyota Tundras. Now we understand there's been some confusion as to how you hook up the power fold feature in vehicles that were not equipped with factory power fold. To make it clear, we're going to show you exactly where this harness connects into your mirror as well as where you should be expecting to make these other connections to hook up your aftermarket power fold feature.
This red wire will be stripped and installed into this butt connector here, which leads to our add a fuse circuit here—which will remove a factory five amp or higher fuse from your fuse panel. We recommend something like your cigarette lighter, that will only work with the vehicle's power on. You will remove that fuse. Install this and install the fuse you removed into this open terminal here, while this will supply power to the switch. This black wire will be attached to a rust free clean bolt on bare metal somewhere underneath your dashboard to ground this switch to the chassis.
The green connector will connect into your switch, which you'll cut a hole and mount into your dash. Now if your vehicle did not have the factory power fold, this connection needs to be tapped into the mirror. This is where a lot of people have been having trouble. What you have to do is peel the backing here off the base plate of the mirror. Down where your connector is that your factory wiring harness will plug into. Inside you'll find this white and yellow connector here going into the connector for your factory harness.
This is looped from the factory to make sure if your vehicle had factory power fold that this option is plug and play. However, for those of you watching this video, to add this feature to your vehicle, you want to disconnect this connector, run it through the small opening and this shielding, lay the backing back into place and connect the appropriate side of the harness included with your kit to that connection. If everything is hooked up correctly, this will allow the power fold function to work off of the aftermarket switch and harness included in your kit.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
MRA04179
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Toyota is a registered trademark of Toyota Motor Corporation. 1A Auto is not affiliated with or sponsored by Toyota or Toyota Motor Corporation.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.