Replaces
Replaces Subaru Legacy Outback Tribeca 6 Piece Ignition Coil Set Delphi DEERK00287
$622.95
Replaces Subaru Scion 4 Piece Ignition Coil Set Delphi DEERK00296
$475.95
Replaces 2013-14 Subaru Outback Driver & Passenger Side 2 Piece Headlight Set DEPO 1ALHP01296
$391.95
Replaces 2013-14 Subaru Legacy Outback Driver & Passenger Side 2 Piece Headlight Set DEPO 1ALHP01286
$389.95
Replaces 2013-14 Subaru Outback Front & Rear 8 Piece Suspension Kit TRQ PSA84798
$364.95
Replaces Subaru Front Driver & Passenger Side 2 Piece Wheel Bearing & Hub Assembly Set Timken TKSHS00519
$359.95
Replaces 2013-14 Subaru Outback Front & Rear 4 Piece Strut & Spring Assembly Set TRQ SCA84826
$334.95
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
The bulbs are for testing and not covered under our warranty. Our warranty applies to the light assembly only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Remove these two threaded clips. Use a Phillips head screwdriver to loosen them. Just kind of turn it and it'll pop up a little bit. Do the same for both. Take our plastic prying tool just kind of get it up underneath there. Pull this clip out. If it doesn't come out that's fine just get the center part out, that basically unlocks it. Use a flat bladed screwdriver here to pop this one out. You need to remove this cover so carefully take the flat bladed screwdriver. Pop it up and take it out. There's two 10 millimeter bolts here. They do have Phillips head openings, but I'm going to use a 10 millimeter socket extension and ratchet to remove them. So start with the top one. These are just threaded self-tapping bolts going to grommets. Remove both of them.
Taillight assembly is loose, just pull it straight to the back. Start pulling it off the clips here and here. And now we have access to the bulbs. Counter clockwise to unlock that bulb socket. Do the same for all of them. Just let them hang and remove the tail lamp housing.
To install the tail lamp start with the harness around here. Install the turn signal bulb. It goes in the lower one. Turn it clockwise to lock it. Brake light bulb. Turn it clockwise to lock it and the same for the side marker bulb.
These two pins here line up with these two clips here. So to push them in, right up against the body with the tail lamp. It snaps into place.
Reinstall the 10 millimeter bolts. Once they get tight I'll just stop. Reinstall the trim cover. One of these clips is broken, this one's still good. It slides in this way. Now there was a clip up here that slid into here. Goes in. Slide it up and around. Push this clip in place, just kind of snaps down. This one push the center in 'cause they came apart and then push this middle part in to lock it.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
