Replaces
Part Details
TRQ side mirrors and mirror components are designed to match the function, fixture, and performance of the original version for easy installation. TRQ mirrors are DOT certified, comply with all federal safety standards, and are independently lab tested to ensure our products comply with all government regulations. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Exact fit - To obtain proper fit and function confirm your vehicle has the exact mirror options listed.
Paint To Match Note:
"Paint-to-match finish" refers to a smooth, paintable surface. This item is not painted. Paint offers better coverage and adhesion, but it is not necessary for installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
What's up, guys? Here we have a mirror from 1AAuto.com. I'm going to be installing it on this 2014 Nissan Versa. The advantage of this mirror is it's a direct fit replacement. It's going to be cheaper, and it's going to function exactly like OEM. Get yours at 1AAuto.com, and you'll be ready to rock and roll.
We're going to take this door panel trim off. This goes over the mirror. Just use a trim tool. Pry underneath here, over here. It comes off. There's a clip that holds it on there, clips that holds it on there, and a little pin. I'm going to use a 10mm socket and extension and ratchet. We're going to take these nuts off. This nut's a little bit tricky to get to, but it is possible to do it without taking the whole door panel off.
Take this one off first. Be careful not to drop the nut. Pull the nut out. Take this nut off. Before I pull the last nut out, we have to remove this section where the adjuster is. Underneath here, there's a little tab. Push up on the tab, and then this will rotate this little button. Can move this rubber piece right here and this will slide off just like that.
Now, when we take this last nut out, we're going to support the mirror from the outside. Pull that nut off. We're going to pull the mirror straight out. This is our old mirror. This is our new mirror from 1AAuto.com. The shapes are the same. The new mirror comes with this cover off, so that if you had one that was painted, you could transfer it from your old mirror to your new mirror, or you could paint this and then install it. The controls are the same. The mounting studs are the same. You're going to want to take these things off. These are just protectors to protect the studs during shipping. Get yours at 1AAuto.com, and you'll be ready to rock and roll.
To install this mirror cap, I'm just going to align this up with the holes in the mirror. Line it up and just lock it in place. All right. Now we're going to install the mirror. We're going to make sure to line these studs up with the holes in the door. Slide this adjuster through the big hole and line the studs up. Make sure you have the nut in your hand when you go to install the mirror so you can put it on right away. Then you can release your hands from the mirror.
I'm going to slide this in. There is a slot for the adjuster. It goes in the top part of this bracket and slide through like that. And then this bracket, this top part's going to slide in here and then it's going to click into place just like that. You can take these other nuts and get them started, and we'll take our 10mm with the extension and our ratchet and we'll just snug it up not too tight, just snug. These are pretty good. Take this rubber piece and slide this over here. You can make sure it works up and down, left and right. It's working properly. Take our cover, slide it over, line it up with the holes, and lock it in place.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
