Replaces
Part Details
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
This video will detail headlight replacement on 2000 to 2006 GM SUVs pickups.
This replacement is similar for our 2000 to 2006 Yukons and Yukon Excels, 2000 to 2006 Tahoes and Suburbans, 1999 1500-series pickups to Sierra and Silverado, and 2007 classic series.
The headlight procedure is the same for all trucks that look similar to our example truck a 2002 Yukon Denali. It has the projector beam headlights. The procedure to replace the headlights is the same, whether or not you have the projector beam headlights or regular headlights. No tools are required for this and it only takes about three to five minutes.
The process to remove the headlight is very easy. Open your hood, locate the pins that hold them in, twist them, hold them up, and remove them to release the headlight from the mounting bracket.
Then, pull the headlight forward. Locate the low beam and the high beam connectors. Disconnect the connectors by putting your thumb into the connector and pulling.
Now the headlight is free from the vehicle. Get your new headlights and reconnect the low beam connector. Now reconnect the high beam connector, and then slide it back in the vehicle, making sure that on the pigtail of that low beam connector is pushed back into the hole so it doesn't get caught between the headlight and the mounting bracket.
Now press everything down and lock them back into place and you're done. Do a test and you're set.
Again, this goes for most 2000 to 2006 GM Trucks and SUVs.
Tools used
To open the hood on this 2005 Avalanche, open your door. Pull the release. The secondary release is actually under the emblem here. Push it to this side, and lift the hood up. To change this headlamp, you first have to remove the turn signal lamp. Reach down, push this tab in. Push this tab in right here, pull it out. Now, we're going to pull the headlamp away from the grill, off the tabs that it's mounted on. Push this in. Turn it counterclockwise to remove the bulb and socket. Turn the marker light bulb counterclockwise to remove it.
There are two pins, L-shaped pins, one here and one here. I'm going to unlock those to remove the light. I'm going to use a flat-bladed screwdriver to pop it out. Pull it straight out. Same thing over here. Pull it straight up and out. Put those aside. Headlamp is free. I'm going to unlock the connector on the lamp on the bulb and push it down. Pull it off. I'm going to undo the other side. I'm going to pull the clip or the lock on it away from the headlamp, and I'm going to push down on the connector at the same time to pull it off. Then, you can lift the light up and slide it out.
Here's our old yellow and discolored headlamp. It's all pitted from going down the road. You can't really see that well out of this. This is our new one from 1aauto.com, perfectly clear. You're going to have great night vision with this. It comes with two new bulbs, and look at the old one. It has the same style of mounting and the same shape. It'll fit great and look great.
I'm going to take our new head lamp. I'm going to feed that up like that. That has the adjustment for it. I'm going to plug in our connectors. Place it into the little mounting area. We'll reinstall these L-pins. This one will slide down just like that, and I can move it around a little bit to line it up. You flip it over and lock it in. Same thing with the other side. You need to wiggle the headlamp a little bit to get it in there. You want to flip it over and lock it. The headlamp is installed.
Now, reinstall your turn signal lamp. Turn this clockwise to lock it. Install the side marker bulb. Turn it clockwise to lock it. Put these tabs into the radiator support. Push this up and in. If you need to adjust the aim of the headlamp, you can turn this screw in or out.
This is a basic tutorial on how to aim the headlights on your vehicle. Find the axis of your headlights. This is usually indicated with a small dot or the headlight bulb size on the lens. If not, it's the actual center point of your headlight bulb. Transfer this mark to a vertical wall with a preferably dark color that'll allow you to back up 25 feet. Pull up and find the center line of your vehicle, as well as the center line of your headlight axis.
Mark the wall with the height of the headlights and a straight line going across at that axis height. Back your vehicle up 25 feet from the wall to the front edge of your vehicle's headlights. Turn your headlights on, and locate the adjusting screw, usually on the back side of your headlights. You'll want to rotate this until the passenger hot spot or focus of the beam is approximately two inches below the line and the driver's side is four inches below the line. We change the heights on each side so you can still get a good beam to the off side of the road on the passenger's side and have the driver's side low enough to not blind oncoming traffic.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service the lower front light. This is the side marker light, the signal light, as well as your daytime driving lights. We'll show you both changing the bulbs, as well as if you want to replace it with a whole new assembly from 1A Auto. If you go for it, a new set of lights on the front end of your truck will take miles off, make it look a whole lot better, and help you see better at night. You won't need any tools for this. You may want a flat blade screwdriver.
Open up the hood by pulling the lever here. Reach under the center of the hood, you'll see a little lever right here. Push it towards the center of the truck and lift up.
The headlights are pretty easy. There's actually a little lock bar right here. Pull it up out of the clip. You might have to work it back and forth as you pull it towards the center of the truck. This pulls right out, and then your headlight tilts back and out. Right in behind, your headlights are connected. You don't have to have the battery disconnected. As long as the truck's off, there's no power going through here. Just pull back on these tabs and push off the connectors, and your whole assembly comes out.
Now if you're just looking to change the amber signal bulb, it's right here. There's a little tab. Press down, twist counterclockwise, and that comes out. Twist back in to lock it. Do the same thing, here, with your driving light: on the little tab, push down, twist counterclockwise, and that can come out. I've pulled that out for right now.
If you want to remove the whole assembly, just push the little tab right here. Push this tab towards the outside of the truck. Most of the time I'm able to push this tab just with my fingers and pull the light out, but it's possible you may want to use a flat blade screwdriver, here, to help you push on the tab, and then even twist it a little bit to help pry that tab from the body of the truck. The whole thing comes out. Disconnect here. Your marker light is down here, just twist it counterclockwise, pull that out, and the whole marker comes out.
Just to show you, here, on these bulbs, I just pull right out of their sockets like that, and they go back in.
Reinstall the new light from 1A Auto. It's going to go in just like the original. Put your marker in first. Push through the signal bulb, and your other bulb. There's a tab right here on the inside, make sure it goes into the radiator support. Then just watch this tab go right in, and it snaps right in place.
f you had some damage or your lights are clouded or faded, the new light from 1A Auto is going to go in there just like the original. It plugs in. The bulbs plug in just like the originals. On the bottom, there are two tabs that go into slots here, so you kind of feed it in behind the grill, and peek back in there so you can see those tabs going into the right spots. Once they're in, then, line it up right here. Push it back in, put the pin in and through, and just push it through until it locks down in place again. Then, for the new light, peel off the plastic covering.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to remove and then reinstall the front grille. This is a 2005 Silverado, and it's pretty much the same for any '04 to '07 Silverado with this style headlights and grille. At 1A Auto, we sell a nice replacement grille if yours has been damaged. You will need a flat blade screwdriver. I'm going to show you this. The grille on this truck is in good shape so I just take it off and put it back on, just to show you how to do it.
Open up the hood by pulling the lever here. Reach under the center of the hood. You'll see a little lever right here. Push it towards the center of the truck and lift up. First, there are four clips. Just use a flat blade screwdriver and pry under, and get the center of the clip to come up. Okay, so you can see there's the center up. I'll just do that for the other three here. There are just four right across on the front of your radiator support here. You can either pull the centers right out or, sometimes, the whole clip comes out. Pull the centers up and out, and then the second part of the clip comes out. That's probably the easiest way. Now, there are six attaching points. There's one right back in here, one right here and then one under here. You just got to pull nice and firm. Put your fingers right in behind there. Give it a good, firm pull. Right up here, give a good pull. Grab right down here, and give a good pull, and on the other side, do the same thing. The whole grille comes right off.
You want to transfer your emblem over, there's two 10mm speed nuts, just remove those. Take your emblem off, put it on the new grille. You can see my old one's in good shape. I'm not going to replace it on this vehicle, but I'm just going to show you. Put it back carefully into place. Make sure that this part here goes underneath. There are guiding pins right up here and down at the bottom, guide you right into the right spots. I can see right here, so I'm going to clip that in. Clip that in, and it clips in nice and easy. On the outside, you might want to just push in, just a little bit, and right back on. I'm Going to take our top clips and just put the bottom part in first. Then, just follow up with the locking centers and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
