2005 Pontiac Grand Prix with 34mm Diameter Front Sway Bar Front 10 Piece Steering & Suspension Kit TRQ PSA63529

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace an outer tie rod on this 2003 Chevy Monte Carlo. We show you on the passenger's side but the driver's side is the same procedure. The items that you'll need for this is a new outer tie rod from 1AAuto.com; 7, 17 and 19mm socket and ratchet; two adjustable wrenches; a hammer; pliers; a tape measure; a grease gun; and jack and jack stands.

Start off by just loosening up these lug nut caps. Now, you can remove your lug nuts. If you don't have air powered tools, you want to loosen these up while the vehicle is on the ground, then raise the vehicle and remove them the rest of the way. If you do have air powered tools, you can just remove them right here. You can just pull your wheel off.

Measure from the boot on your inner tie rod to this grease fitting on your outer tie rod and just remember this distance. Then, you want to loosen up this nut right here and put one wrench on the outer tie rod, one on the nut and push opposite directions to loosen it up. We recommend using two adjustable wrenches. Next remove the cottering pin from the bottom of the outer tie rod, just use your pliers to straighten out the pin and then pull it free. Now, remove this 17mm castle nut. Hit the knuckle with a hammer. This will loosen up the outer tie rod and you can lift it up and out. Just turn the outer tie rod counterclockwise until it comes free and then remove this nut.

On the left is the old outer tie rod, on the right is the new one from 1A Auto. You can see they're identical and they'll fit exactly the same. Put your new nut into place and then twist the outer tie rod on. Then, lift your outer tie rod up and into the wheel knuckle. Just push it down through. Measure it again from the end of the boot to the middle of the grease fitting and make sure it's the same. This is a good preliminarily alignment, but you probably still want to go get your vehicle aligned and have it adjusted and then put the castle nut back on, tighten it up, and then push the cotter pin through and bend the tabs in opposite directions. Using your two adjustable wrenches, just tighten this nut up. Then twist in your grease fitting, and using either a 7mm socket and ratchet or a 7mm wrench, just tighten it up. Then, using your grease gun, fill it with grease. Clean up any that came out on the sides. Turn your wheel. Then put your wheel back into place and replace the lug nuts. While the car is on the jacks, you want to replace the lug nuts and tighten them preliminarily, lower the vehicle, and then tighten them the rest of the way. Torque each of the lug nuts to 100 foot-pounds in a crossing pattern. Then replace your hub cap and tighten up those lug nut caps.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a front sway bar link on a 2006 Chevy Impala. It's the same for model years 2000 through 2012, and the procedure is exactly the same on the left side, and on the right side. To perform this repair, you'll need a 13, 14, and 19 millimeter sockets and socket wrench; 13 and 14 millimeter wrenches; some penetrating oil; a hammer; flat blade screwdriver; and a jack and jack stands.

Start by loosening the five plastic lug nut covers that hold the wheel cover to the wheel. For taking off the wheel, you'll be using that same 19 millimeter socket, but if you don't have the benefit of a lift or air tools, start with it on the ground. Loosen up your five lug nuts slightly. Get it safely on some jack stands and then proceed to remove the five lug nuts with your socket, socket wrench and breaker bar. Then take off your tire. I

'm going to turn the steering knuckle there a little bit so you can get a good look at the sway bar link, which is between the control arm and the sway bar. I'm using a 13 millimeter socket and socket wrench, on the bottom, and then I'm counter holding it with a 13 millimeter wrench up top, and I'm going to go ahead and fast forward as I loosen those up. The bolt that goes through the center there is quite corroded and sticking to the rubber bushing, so I'm going to use some penetrating oil. I'm going to try and separate the bushings and those washers, as well as the bolt that goes through the control arm, all the bushings, and the sway bar, using a flat, long screwdriver to try and get some room, and start to pull that away. Once I do, I can just use a hammer on the top and tap it out. As you pull everything out, you'll just want to remember the position of everything, how the bushings and the washers go in.

Here you'll see the old part, rusted and corroded, and the new part from 1A Auto. That, there, is how it will go back into the car. I'm going to start with a rubber bushing against the control arm and then a washer. On top of the washer I'm going to place the metal sleeve. I'm going to use the pry bar to lift up so that I can get, then, another rubber bushing, place it on top of the sleeve with a washer underneath it. As I lift it up then I can let it down and it'll fall right into place. I've got the bolt going from the bottom with a rubber bushing. It's got the bolt, then a washer and then the rubber bushing that's going to be sitting next to or against the control arm. You can see there. You might have to twist or pull some of the stuff to get it to line up so it goes through. Again, here, I'm using a hammer. I'm going to use the pry bar again to pry up on that sway bar to give me a little bit more room. Then once I get that pushed through, I'm going to put another rubber bushing and a washer, and then the nut. Then, to summarize, from the bottom up, you've got the bolt, washer, rubber bushing, control arm, rubber bushing, washer, sleeve, washer, rubber bushing, then the top of the sway bar, then a rubber bushing, a washer, and then the nut. I'll go ahead and fast forward as I use a 14mm wrench and a 14 millimeter socket and socket wrench to tighten up the sway bar link.

I'm reinstalling the wheel and I'm going to tighten by hand the five lug nuts. Then, once I do that, I'm going to tighten them back up with the impact wrench, and then as I get the car down, I'm going to use a 19 millimeter socket with a torque wrench, and torque all five lug nuts in a star pattern to 100 foot-pounds. Then, go ahead and reinstall your hub cab, lining up the notch in the hub cap with the valve stem, and then go ahead and tighten up those plastic lug nut covers

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace a front sway bar link on this 2003 Chevy Monte Carlo. We show you on the passenger's side, but the driver's side is the same procedure. The items you'll need include a new front sway bar link from 1AAuto.com, 13mm, 14mm and 19mm socket, a ratchet, a 14mm wrench, and jack and jack stands.

Start off by just loosening up these lug nut caps. Now you can remove your lug nuts. If you don't have air-powered tools you want to loosen these up while the vehicle's on the ground. Then raise the vehicle and remove them the rest of the way. If you do have air-powered tools, you can just remove them right here. For this repair it's important to note you have to have both wheels off the ground. You can't just jack one wheel up. It'll make this repair difficult.

Spray down the top of the link with some penetrating oil. Then use a 14mm wrench to hold the top, and a 14mm socket and ratchet on the bottom. Now, this actually comes apart easily. It's not uncommon, but sometimes the link is totally broken and you don't even have to do this step. You just pull the remains out. Also, sometimes they're frozen up so bad you have to use a saw or a torch to cut the links out. Pull the top bushings off and push the sway bar link down and out, and then remove the bushings in the center.

Take your sway bar link and put the center bushings in first. Then run your sway bar link up through the bushings. Then replace the top bushing, the washer, and the nut. Just twist that nut on. Once you have it on there securely, you want to lower your vehicle down onto the jack stands so that all the pressure is on the suspension. Then tighten up the sway bar the rest of the way.

Then replace your wheel and each of the lug nuts. You want to just tighten them preliminary, and then lower the vehicle and tighten them the rest of the way. Now torque each of these to a hundred foot-pounds in a crossing pattern. Then replace your hubcap and tighten up the lug nut caps.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.