Kit Includes: (1) Front Driver Side Exterior Door Handle (1) Front Passenger Side Exterior Door Handle
Handle Color: Black
Quantity: 2 Piece
Finish: Paint to Match
Specification
Side Location
Driver & Passenger Side
Location
Front
Paint To Match Note:
"Paint-to-match finish" refers to a smooth, paintable surface. This item is not painted. Paint offers better coverage and adhesion, but it is not necessary for installation.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Exterior Door Handle 2000-07 Chevy Monte Carlo
Created on:
Tools used
Socket Extensions
Flat Blade Screwdriver
Phillips Head Screwdriver
Putty Knife
10mm Socket
Ratchet
T25 Torx Driver
1. Removing the Door Panel
Remove the Phillips head screw at the front top corner of the door panel
Remove the Phillips head screw inside the door handle
Remove the two T25 Torx screws under the pull handle
Pry off the trim piece inside the door handle with a flat blade screwdriver
Pry off the door lock switch while pulling up with a flat blade screwdriver
Slide a putty knife into the side of the door panel and pry out on the clip
Pull out sharply to release the clips around the door panel
Lift the door panel up and pull it back
Pull the switch panel harnesses free
2. Removing the Exterior Door Handle
Pry out the exterior door handle cover
Unclip the harness and pull the water shield back
Pry out on adhesive on the foam block, make sure to keep the adhesive to the block
Remove the two 10mm bolts holding the exterior door handle with socket extensions
Pull and unclip the yellow clip in the door and remove the rod
Push from the inside and pull from the outside, pull the front down and out and twist it
Release the rod and pull the door handle free
Pry out on the lock cylinder clip with a long blade screwdriver
Pull the lock cylinder up and out
3. Installing the New Exterior Door Handle
Push the lock cylinder into the new exterior door handle
Re-clip the door handle rod into the exterior door handle
Place the rod down in between the track in the window channel
Feed the exterior door handle back in
Re-clip the exterior door handle rod into the yellow clip
Tighten the two 10mm bolts holding the exterior door handle with socket extensions
Replace the exterior door handle cover
Insert the foam block and water shield into place
Re-clip the harness and replace the water shield
4. Reinstalling the Door Panel
Reconnect the switch panel harnesses
Put the door panel down into the window sill
Lineup and re-clip the door panel
Reconnect the door lock switch into the door handle panel
Replace the trim piece inside the door handle
Tighten the Phillips head screw at the front top corner of the door panel
Tighten the Phillips head screw inside the door handle
Tighten the two T25 Torx screws under the pull handle
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an exterior door handle on this 2003 Chevy Monte Carlo. We show you on the driver's side, but the passenger's side has a similar procedure. The items you'll need for this includes a flat blade screwdriver, a Phillips screwdriver, a T25 Torx driver, a putty knife, a 10mm socket, and ratchet with an extension.
Your door panel is held on with four screws. There's a Phillips screw here and a Phillips screw up here, and then down here under the pull handle there's two T25 Torx screws. We'll just fast forward as Mike removes those. Now, pry out behind this panel with a flat blade screwdriver, and then slide the panel forward and over the door handle. Then pry out on both sides of your door lock switch while pulling up on it. It should pull free.
There's an indent right here that you want to slide your putty knife into, and then just pry out on the clip. Then reach back behind the door panel and feel for the clips, and just pull out sharply to release the clips. Once you've release them all the way around, just lift the door panel up and then pull it back. Push the tab on this harness and pull it free. Do the same thing for this harness. Your door panel is free. Push on the tab on this harness and disconnect it. Unclip the harness from the door and pull it aside. Carefully, without damaging the water shield, you want to just peel it back.
Pry out on this clip, and then pry out on the adhesive on either side of this foam block. You want to make sure that you keep the adhesive to the block so you can stick it back into place later. If any of it peels off, make sure you push it back into place.
In these holes, you'll see two 10mm bolts, one there and one right there. Just go ahead and remove both of those. Inside your door you'll see this yellow clip. Just flip it forward and it will open up, and you just pull that rod free. You'll need to reach in and kind of push up on the door handle and pull out the bottom. Push the front of the door handle down, and pull it out. Then angle the back of the door handle down and pull it free. You want to just pull it up until you can access this lower rod right here and just pop it out. Then pull the door handle rod up and out. In your new door handle you're going to want to transfer over this rod, so just unclip it and maneuver it out of the door handle. You'll also want to switch over your lock cylinder, so just pry out on this clip and then just pull the lock cylinder up and out.
Take your new exterior door handle and push the lock cylinder into it and then push your door handle rod back into place and re-clip it. Feed the back end of the door in first. You've got to make sure that this goes between the track and the door lock access here. Then push this rod back into place. Get that rod down in, and just angle the back of the door handle up. Push it back and then angle the front of the door handle into place. Take your exterior door handle rod and re-clip it into this yellow clip and push the clip closed. We'll fast-forward as Mike replaces those two 10mm bolts and tightens them up. Just replace this cap.
Feed the foam block back into place and re-clip the top of it. We'll just fast-forward as Mike replaces the cover around the handle and the water shield. Push your weather strip back into place. Reconnect this harness and re-clip it to the door. To reconnect your door panel, just start off by reconnecting these two harnesses. Just put this switch through here, and then line up these slots with these four tabs. Just lift the door panel up, and push those slots onto the tabs. Then just make sure the clips are wind up, and hit them into place around the sides of the door panel. Push your door lock switch back into this panel. Slide the panel over your interior door handle and slide it back into place. Then just replace those four screws, and you're all set.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
DHA32210
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.