Replaces
Replaces Chevrolet GMC 12 Piece Tailgate Repair Kit DIY Solutions BHS00148
$76.49
Replaces Chevrolet GMC Tailgate Latch 4 Piece Kit TRQ BDA39849
$59.95
Replaces Chevrolet GMC 8 Piece Tailgate Repair Kit DIY Solutions BHS00141
$49.37
Replaces Chevrolet GMC Tailgate Latch Rod 2 Piece Set TRQ BDA80714
$39.95
Replaces Chevrolet GMC Hummer 4 Piece Tailgate Hinge Set TRQ BDA64723
$34.95
Replaces Chevrolet GMC Driver Side Tailgate Latch TRQ BDA64639
$29.95
Replaces Chevrolet GMC Passenger Side Tailgate Latch TRQ BDA64725
$29.95
Replaces Chevrolet GMC Hummer Tailgate Handle TRQ DHA69380
$29.95
Replaces Chevrolet GMC Tailgate Handle Bezel TRQ DHA69388
$18.95
Replaces Chevrolet GMC Cadillac Hummer Tailgate Striker Bolt TRQ BDA65283
$14.95
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Going to replace this handle, tailgate handle, on this Chevy pickup truck. The bezel has already broken off on this vehicle. It's pretty common for them to break off. This is a brand new bezel from 1AAuto.com.
The way it fits in here if this truck had the bezel, these two little tabs on the bottom slide in these two little holes here. There’s push tabs up top here. And it would sit in like this. These tabs would lock underneath the sheet metal. If you were trying to remove it, carefully take a small screwdriver and push it in here on either side to release these tabs. Most likely if this bezel is old, it's just going to break on you if you're trying to replace this handle. You should probably have one of these on hand before you try to replace this handle.
Let's get into replacing this handle. After I sprayed some rust penetrant on these clips so that they'll move more freely, I'm going to push them down with my index finger. I'm not going to pull the rod out of this yet. It will just slide out, but I want to leave it in there, because I need the latch to work still. But it's easier to pop these off while this latch is attached to the sheet metal so it's not moving around on me. Now I can still open the latch and lower the tailgate.
There's two bolts here, and there's a third bolt that's hidden under this plastic bed liner, which is held in with these Phillip head screws that are all around it. I'm going to remove these, take off the plastic bed liner, and get to these three bolts that are back here. Use a Phillips head screwdriver to remove these. If you had a painted on bed liner, you may have to take a razor blade and cut around these bolts, but since this is a plastic one this plastic piece has to come off. These are the final two bolts.
I've removed all the screws that are holding this plastic on. These bolts are also holding the top of the latch. Start by taking these out. This is a 13mm socket. Lift this plastic up, put it in the bed of the truck so it's out of the way. And you'd see the final bolt. I'm also just going to hold onto the latch, because it's going to be pretty loose. Lift up the tailgate.
Since I've already freed these, I'm going to pull the rods out that go to the latches. This latch will slide right out of the opening, and you just have to maneuver it out. It's a little tight.
This is our old handle. This is our old handle from the vehicle, and here's our brand new one from 1AAuto.com. See, same exact design, same three bolt holes, same spring, same style black textured plastic. This will fit great and work great for you. This is a brand new bezel from 1AAuto.com. It goes around the tailgate handle like this, matches, same black texture.
If yours is broken off, this will replace it and make your truck look new again. Take our new handle, slide it up into place, align it up with the original bolt hole and go inside the bed. I'm going to capture this bolt here so that it doesn't move too much around on me. I'm not going to fully tighten it, I'll just leave it loose. I just want the handle in place.
Now I can push these little control rods up here that work the latches on either side, and get this one in to move that around a little bit. It's going to slide right back in there, pushed in. Then this goes up to lock it in place. Same thing on the other side. Adjust this over, can move this around a little bit, and do that. These are a little rusty. Push them in place, flip this around, and lock. Now I can open the tailgate again.
I can see the handle is lined up with the holes here. See it moving there? I'm going to hold it where I want it. I'm going to tighten this one, because once I put the plastic over it. I won't be able to get to it. Once it feels tight, I'm going to stop. We can lay out plastic bed liner back down, fits right into place. I'm going to replace these two bolts, tighten up the last bolts, real tight. I'm just going to stop, same thing with the other one.
And go and replace the rest of the Phillip head screws that are holding the plastic bed liner trim in. With the bed liner reinstalled, I can close the tailgate. Now would be a good time while you can get in here, to spray some lubricant on the hinge. That works really well. I'm just going to wipe up some of this oil that spilled. We can install our new bezel, and put the two tabs in these bottom openings here, and then snap it into these two top tabs, flip it up and over, just like that. You can open the handle a little bit. Whoops. A little tricky. New bezel is installed.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we'll be installing a tailgate cable on a 2004 GMC Sierra. It's basically the same as any GMC Sierra or Silverado from 1999 to 2006. The only tool you'll need is a 1/2 inch wrench.
Open up the tailgate. You got a bolt here. It's a ½ inch bolt. Remove that. If it's frayed, you can replace it. Not a difficult thing to replace at all. Most people can do it. If you're wondering how, that's how. A couple of keys, make sure if you're replacing one, the other one's in good shape. You don't want the tail gate to fall because if it falls, it will hit the bumper and it will get dented. Don't take them off both at the same time.
Just one little thing: When you're tightening it, you see the tailgate cable's made to go around the flint in this bolt. You need to lift up and make sure the tailgate cable goes on the bolt, and then tighten it. This allows that to keep moving. If you're tightening it up with getting it in that right spot, basically what will happen is your tailgate will just going to stay like this. This would end up pinching into there and probably damaging and scratching things. That's about it.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace a Tailgate hinge on this 2002 GMC Sierra 2500HD. It's the same process on most 1999 to 2006 GMC Sierras and the Chevy Silverados. The tools you'll need are 13 millimeter socket and ratchet, penetrating oil, anti-seize and it's helpful to have two people as you'll see in this video.
You want to start by just putting the tailgate down. As you can see, the hinge on this truck is in pretty bad shape. You want to just push the cable up and then it should pull off. Depending on the condition, this could be a little difficult, but just keep moving it around, and it should pop off. Now, while he tries to get that cable off, this is where it's helpful to have a second person. So, the other person can hold the other side when it comes free, and the two of you can move it aside.
Here's a closer look at the condition the hinge was in. As you can see, it's in pretty bad shape. We just want to spray these bolts with some penetrating oil. This is going to help to remove them. Now, you just want to use a 13 millimeter socket and a ratchet to just remove these two bolts. We'll fast-forward as he removes these. Now, what you want to do is you just want to pull this bracket off. This one just comes right off. Just move it around a little bit. Then, we'll fast-forward as he removes the two 13 millimeter bolts on the opposite side. This hinge is a little bit harder to get off. He's having to use a flat blade screwdriver to kind of pry it from the truck. There it is.
Now, what you need to do is you need to remove the two 13-millimeter bolts on the tailgate itself. We'll fast-forward as he removes these two. The clip should just come right off. We'll just fast-forward as he removes the other two bolts and the clip on this side.
Here are, obviously, the new hinges on the bottom and the old hinges on the top. The hinges from 1A Auto are going to be an exact replacement, and they're going to bolt-in just like the original and work a whole lot better.
So you can see here, he's just pointing out that they're marked "left" and "right." The left side is going to go on your driver's side, and you're going to want to take the shim off the old hinge there and just put that on to the new one. What he is doing right here is he's just putting some anti-sieze onto those bolts. You just want to put that shim and hinge into place and put the bolts into place. We'll just fast-forward here as he tightens up those 13 millimeter bolts. Now, you want to follow the same process on the other side, just putting the anti-sieze on the bolts, putting the hinge into place and tightening those bolts.
Again, you follow the same process, this time, for the hinges on the actual tailgate itself. You're going to want to put the round, the full-circle end on to the driver's side of the tailgate and the half one on the opposite side. We'll just fast-forward through this process.
Now, you're going to want the second person again, and you're going to put the driver's side end on first and angle the other side up and on to the hinge, and then connect those cables on either side of the truck. As you can see, everything looks a lot better now.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Hi, I’m Mike from 1A Auto. We’ve been selling auto parts for over 30 years!
Now, replaced the tailgate cable. This one is missing the lock tab. It's real beat up. So I'm going to start. I can undo it from up here by just lifting the tailgate up, pushing it over that, lay it down. I'm going to do these one at a time so the other one on the other side will help hold the tailgate in place. I need to remove this bolt here. It needs a 13 millimeter socket. So it’s getting pretty loose. I can take it out with my fingertips. Put that bolt aside—I don't want to lose it. There's our old cable.
This is our old tailgate cable from our vehicle; this is our brand new 1AAuto.com. See, it's similar in design. Same length, so this will work great and hold our tailgate up.
Let's take our new cable and original bolt. There's a washer underneath there. There's a small washer under here that kind of fell out of place. Take a small flat bladed screwdriver and just hold it back up Where it belongs. There it is. Put my bolt through the cable and the cable in the hole. Got to tighten this down until it stops. The bolt has a shoulder on it so this can move. Now we can reconnect it and move these to lift the tailgate up. Place it over, push it in because that lock tab is there, and then we're going let it come down, and now it's locked into place. The cable is replaced. So the other side is going to be the exact same procedure.
So we're going to lift up on this one because it's not broken, lift up on the tailgate, push it out. Remove this bolt. I'm just going to take it out with my fingers. Place it all to the side, take our brand new one from 1AAuto.com. That little washer has fallen down. Pull this up, thread the bolt in, and tighten down with my socket ratchet. There we go. To reinstall this lift up on the tailgate, push it down, now it's locked into place and both cables are replaced.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
