Replaces
Replaces Chevrolet GMC Buick Saturn Front & Rear 6 Piece Complete Strut Assembly & Shock Absorber Kit TRQ SKA64309
$359.95
Replaces Chevrolet GMC Buick Saturn Rear 12 Piece Suspension Kit TRQ PSA69630
$354.95
Replaces Chevrolet GMC Buick Saturn Front & Rear 6 Piece Suspension Kit TRQ PSA85139
$299.95
Replaces Chevrolet GMC Buick Saturn Front & Rear 4 Piece Complete Strut Assembly & Shock Absorber Kit TRQ SKA61012
$269.95
Replaces Chevrolet GMC Buick Saturn Rear 10 Piece Suspension Kit TRQ PSA69629
$249.95
Replaces Chevrolet GMC Buick Saturn Front & Rear 4 Piece Shock & Strut Kit TRQ SKA63356
$174.95
Replaces Chevrolet GMC Buick Saturn Front & Rear 8 Piece Suspension Kit TRQ PSA39176
$171.95
Replaces Chevrolet GMC Buick Saturn Rear Driver & Passenger Side 4 Piece Shock Absorber Set TRQ SBA64324
$164.95
Replaces Chevrolet GMC Buick Saturn Rear 4 Piece Suspension Kit TRQ PSA64853
$119.95
Replaces Chevrolet GMC Buick Saturn Rear 2 Piece Coil Spring Set TRQ SSA70070
$114.95
Replaces Chevrolet GMC Buick Saturn Rear Driver & Passenger Side 2 Piece Shock Absorber Set TRQ SBA60421
$64.95
Replaces Chevrolet GMC Buick Saturn Rear Shock Absorber TRQ SBA60758
$42.95
Part Details
TRQ fully loaded shocks and struts are manufactured using premium raw materials and calibrated to restore original ride comfort. TRQ shocks are fully loaded featuring a pre-loaded bearing plate, upper and lower spring isolator, upper spring seat, coil spring, boot kit, and premium strut. TRQ recommends replacing your shocks or struts in pairs to ensure even wear of components and improved ride comfort. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Our direct fit gas-charged shock absorbers help restore your vehicle's handling and ride quality to just like new.
Replacing struts used to require specialized tools to compress, remove, and transfer the old spring and mount. Our Pre-assembled, complete strut & spring assemblies come with all new parts and make the job much quicker and easier for the do-it-yourself mechanic.
Strut & spring assembly contains:
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Hi. I'm Mike from 1AAuto. We've been selling auto parts for over 30 years!
Use a breaker bar and a 22mm socket to loosen the lug nuts with the vehicle on the ground. Just go around and loosen them all. Raise and support the vehicle. We're using a two-post lift. You can use a jack and jack stands. Use a socket and finish removing the lug nuts. Take the wheel and tire off.
The wheel and tire is stuck to the brake rotor. I have to put a lug nut on it. Put a second one on the opposite side here. Just lightly take a dead blow. We'll just break it free. It might take a couple hits. It might take one hit. The lug nuts keep it from falling off. Just put the wheel and tire aside.
If the shock bolt that goes through the top is covered with dirt, I’m going to take some rust penetrant, spray it on here, and with a wire brush, try and knock some of that dirt free so when I go to remove the nut it spins off the threads easily, so it doesn't get clogged up with dirt. I have to clean some of the dirt off the end. For the lower one, I'll do the same. Spray it with some rust penetrant.
I'll start by loosening but not removing the upper one. There isn't quite enough clearance to get an 18mm deep socket in here and a ratchet, so I'm going to use an 18mm box wrench. I'm going to loosen the nut, and I have a 15mm wrench to counterhold the bolts. Just keep going until you have the nut almost all the way off. You can change to the open ended part so it'll go a little quicker. I've got this loose but not all the way out. I'm going to spray some more rust penetrant in here. It is moving freely, but I want to make sure it comes out of this part of the shock.
The shock is mounted to the lower control arm with a large bolt that goes all the way through the control arm and is held on with a flange nut. Both of these are 21mm. I'm going to use a 21mm socket and a breaker bar. I'm going to hold the end of the bolt. I'm going to use a 21mm box wrench to break the nut free. It's a lot easier sometimes to break the nut free than try to turn the whole bolt.
I turn this pretty far out on the threads, and then I will use a floor jack to support the lower control arm and remove the lower bolt. Use our floor jack. I'll just lift up on the control arm just a tiny amount. Unthread this by hand now. Let's lift up on the jack a little bit. There it is. We're going to remove this upper nut from the long bolt. Give it a good push. Pull straight through, which is good, or else grab the shocks, and pull the bolt out. I'm just going to push the brake line just gently out of the way. I pulled the bolt out. I'm also supporting the shock. Just like that. Now, I'm just going to work on walking the shock out of the mount here. The hinge is caught on some dirt.
This is the original shock from our vehicle, and a brand new shock from 1AAuto.com. It comes wrapped with this shipping strap so it doesn't fully extend like this one is. I will actually install it with that in there. It also comes with this little conical washer to match the original. That'll go on the inside here. This'll fit great and work great in your vehicle.
I'm going to loosen this bracket here, these two 15mm bolts using a 15mm socket and ratchet. I'm not going to remove them, I'm just going to loosen them. That should give me enough movement. Install our shock. Okay, just slide the long bolt through. Install the nut. Tighten these bolts back up. Just go until they get tight. Now you cut this shipping strapping with some side cutters. The shock will start to expand.
This washer that comes with the new shock, the cone part is going to match the cone part in the control arm. Slide this over. You might have to push up the shock a little bit. Put the bolt through, just like that. The washer will go back around this side, and the large nut. Torque the lower bolt and nut to 74 foot-pounds. Lower the floor jack. I'm going to use a 15mm ratcheting wrench on the bolt end and counterhold the 18mm nut and snug this up. Counterhold the nut with the 18mm, and then torque the bolt's head 52 foot-pounds. It would be ideal if I could torque on the nut, but I can't get it in here with a deep socket.
Reinstall the wheel and tire. Thread the lug nuts on by hand. Now lower the vehicle to the ground and torque the lug nuts. Torque the lug nuts to 140 foot-pounds in a cross pattern.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
