Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Acrylonitrile and Butyl benzyl phthalate (BBP)d, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How To Replace License Plate Lights 2001-05 GMC Sierra 2500 HD
How to Replace License Plate Light 2000-05 Chevy Monte Carlo
Created on:
Tools used
No Tools Needed
1. Servicing the Bulb
Reach under the bumper to remove the bulb
Unplug it from the wiring and replace it
Plug the bulb back into the assembly
2. Removing the License Plate Light Assembly
Pull the light back to unclip it from the bumper
Clip the new license plate assembly into the bumper
Plug the bulb and wiring into the new assembly
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. In this video, we're going to show you how to replace the license plate light, both the bulb and the light itself on the 2002 GMC Sierra, this is the same for pretty much any Sierra, Silverado, Tahoe, Yukon and Suburban of this generation.
To replace the license plate lights, if you're just looking to change your bulb, you reach back in here, you can feel the back of it and you twist the connector counterclockwise, now you can see here's the bulb right here. The bulb pulls out and pushes back into replace it. A lot of times you'll step on here or kind of miss the trailer when you're backing up and wipe out these lights.
You can either use a screwdriver or your hands. You push the light back and pull it out. You can see just a little clip on this end and it comes out. At 1A Auto, we sell the new ones. Ours comes in chrome, so maybe get a pair if you wanted to match. Push it in, then just give it a quick nudge with the heel of your hand. Just turn back up in there, get it to go in. Twist a little clockwise and you are all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
Tools used
7mm Socket
Ratchet
1. Removing the License Plate Light
Remove the two 7mm bolts halfway from the license plate light
Pull the license plate light down
2. Servicing the License Plate Light
Twist the socket out counterclockwise
Pull the bulb free
Push the new bulb in
3. Installing the New License Plate Light
Twist the socket clockwise into the assembly
Replace the 7mm bolts
Slide the assembly back into place
Tighten the 7mm bolts
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to service (as well as replace) the entire license place light assembly on this 2003 Chevy Monte Carlo. The only items you'll need for this include a new license plate light from 1AAuto.com, a 7mm socket, and a ratchet.
Your license plate light is right here, and it's held in with two 7mm bolts. Just go ahead and loosen those up. You only need to loosen them about half way, and then the license plate light will pull down. To service the bulb, just twist the socket out counterclockwise, pull the bulb free, and push your new bulb in. If you're looking to replace the entire assembly we have them at 1AAuto.com, and you can see they're identical and they'll fit exactly the same.
You will have to swap over your bolts, however, and in our case we don't have the option of doing that because of the condition our bolts are in. You may need to find new screws. Otherwise, just swap your bolts over. Twist your socket clockwise into the assembly and then replace your bolts. Slide the assembly forward, back into place, and then tighten up your bolts.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
68167
In Stock
Product Reviews
Loading reviews
There are no reviews for this item.
Customer Q&A
I need a license plate light housing. Are the screws included?February 22, 2020
Jason M
10
Thank you for your inquiry. This purchase will not include new hardware, just the part itself. Please let us know if you have any further questions.
February 23, 2020
A C
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.