Replaces
Part Details
TRQ brake kits are designed to restore your brake system to like-new performance. TRQ brake pads are positive molded, thermal scorched, chamfered, and utilize a multi-layer shim for enhanced performance and service life. TRQ rotors have a non-directional finish that reduces the break-in period for new rotors as well as reducing vibrations throughout the rotor’s lifecycle. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
I'm gonna take the center cap off. Use a straight blade screwdriver to get that off. Use a 22-millimeter socket, take off the lug nuts. Take the wheel off. Take these two caliper bolts out. I'm gonna use a 12-millimeter socket and then a 16-millimeter wrench just to hold the slide from spinning. Loosen these up. Now, just use a screwdriver, pry the caliper off. Pull it out. Then you can use a caliper hanger and just support it from the upper control arm right there. Just make sure there's no tension on the hose. Slide it over here. Take the brake pads off. Just use the same straight blade screwdriver. And take an 18-millimeter socket, take these 2 caliper bracket bolts up. Take these bolts out and slide the bracket right off. Now, take the rotor off. If it's stuck on there, just take a hammer, give it a tap in these areas. Just try not to hit the studs. Keep it loose. Try not to breathe any of that in and slide it off. I'm just gonna clean up this surface right here. You can use a wire brush or some type of grinding wheel. Just be careful, you don't wanna take too much material off. Just get some of the rust off. Take a little anti-seize, just put it on the hub area right here. Now, we're just gonna put the rotor on backwards first and we're gonna clean off the surface. Use a little brake parts cleaner. There is a protective coating on this, clean that up. You can clean up the inside of the drum area as well for the parking brake. Flip that around and clean off this area as well.
When you go to put the rotor on, you may have to adjust the parking brake. You can spin that wheel either forward or backward and...or you can either tighten it or loosen it. Just slide the rotor on just to make sure it spins good. And then double-check with your parking brake and adjust accordingly. Now, take these pad clips off or pad slides or sometimes they call them anti-rattle clips. Just use a straight blade screwdriver. Use a wire brush, clean up any rust built up, right here, and on the other side. With that cleaned up, and then just take a little brake caliper grease, give it a nice thin coat. It's gonna keep the moisture out, keep it from rusting as bad as it was. Then take these clips and slide it in position. Put more caliper grease, just a nice thin coat there and there, wherever the pads are gonna contact it. And then do the same on this side. I'm gonna take these caliper guide pins out. Use a little brake parts cleaner and a rag, clean these up. And I'll also spray a little brake parts cleaner down there. Clean those up with a rag as well. You can drain anything out. And take some brake caliper grease, coat the pin, put it back in. Make sure it seals, and do the same on this one. Slide the brake caliper bracket in place, put the bolts in. You can use a little thread locking compound on the bolts. Now, I'm gonna torque these bolts to 122 foot-pounds.
Now, I'm gonna install the brake pads. Make sure you have the brake pad warning indicator facing up on the outside and also on the inside. Now, take the brake caliper off, take the hanger off. Now, I have to compress the caliper, so use a brake caliper compressing tool. Just compress it really slow. This is gonna push the fluid through the hoses, back through the lines, back up to the master cylinder, and into the reservoir. Just go nice and slow. All right, if that's compressed, pull the compressing tool out. Now, we have a new little bracket right here. It comes with the brake kit. Just take a straight blade screwdriver, this little tab right here, just push in on that tab. Slide that off, take the new one, slide it in there, and then just push it, lock it in place. So, that's in there just like that. This is just gonna push down on the pads and just keep them from rattling around. Slide the caliper over the brake pads in the bracket. Take the two bolts, install the bolts. You can put some thread locking compound on those bolts, and then use my 16-millimeter wrench, 12-millimeter socket, torque these bolts to 31 foot-pounds. And reinstall the wheel, put the lug nuts on. Now, I'm gonna torque these lug nuts to 140 foot-pounds in a star pattern to tighten the wheel down evenly. Then just go around again, double-check. And then reinstall the center cap. Now, I'm gonna pump the brake pedal nice and slow. There's gonna be an air gap between the caliper piston and the brake pad, so we wanna eliminate that air gap. And once the pedal feels good, then you're all set. Check the brake fluid level in the master cylinder reservoir. There's the minimum line right there and the max line right there, adjust accordingly.
Tools used
We're gonna start by taking the wheel off. I'm gonna use a 22-millimeter socket. Take off all the lug nuts. And take the wheel off. Now, we can take these caliper bolts out. I'm gonna use a 12-millimeter socket. Loosen those up. And if the caliper slide is spinning, you can use a 17-millimeter wrench to hold it while you take the bolt out. Now, you can grab the caliper. You might want to rock it back and forth a little bit. That'll compress the piston a little, make it easier to slide off.
And then, you can use a brake caliper hanger, and just hang it from the upper control arm, or you can hang it from the coil spring just like that. Just make sure there's not any tension on the brake hose itself. Now, take the brake pads off, just slide them out of the way. Now, we're gonna take the bracket off. You need to take these two bolts out, use an 18-millimeter socket. Loosen these up. And then, grab the bracket, and just slide it off. Now, you're gonna take the rotor off, just grab it and slide it.
If it's stuck on there, you can take a hammer and just hit in these locations. It's stuck on the parking brake a little bit. Just try to wiggle it. You can just take a prybar and try, and pry in here a little bit. It should get this off. All right. I'm just gonna take two screwdrivers, just try to wiggle this back and forth. There we go, slides right off. Before you put the new rotor on, just take a wire brush, and just clean up some of the rust right here. You could also use a die grinder, and just don't sand down too much. Just get some of the rust off.
Now, you're gonna install this rotor backwards first. Take a little brake parts cleaner, just clean off the backside, and flip it around, and slide it over the parking brake. If you have to adjust the parking brake, you can adjust it right there. And then, spray this side with brake parts cleaner, and wipe it down with a rag. Now, you're gonna take a wire brush, and just clean up this bracket. If you're gonna reuse these clips, just clean these up. If not, take them off.
Just clean up some of this rust right here. Do the same with the other side. And then, just take some brake caliper grease, and just put a nice, thin coat right here. Same on the other side. And then, take these pad slides, and do the same. Put on a nice, thin coat. And then, take these pad slides out. The slide pins. Take a little break parts cleaner and a rag. Just wipe these off. You can clean this out with brake parts cleaner as well. Wipe that down.
Take a little brake caliper grease, and just reinstall it, and do the same with the other side. Now, take the caliper bracket, and line it back up. Brake caliper bolts, get those started. Now, I'm gonna torque these bolts to 122-foot-pounds. Now, I'm gonna put the brake pads on. Now, the warning indicators are gonna go to the top. So, on the inboard pad goes at the top and same with the outboard pad. Just slide them into position. That's good.
Now, I'm gonna take the brake caliper off the hook. Now, I'm just gonna take the old brake pads and a caliper compressor tool and just compress the pistons. You need to push them back into the caliper, and just slowly compress it. You don't want to do it too fast. It's just gonna push the brake fluid through the hoses, through the lines, back up to the master cylinder, and into the reservoir.
All right. That's good. Fully compressed, and just slide it over the brake pads. Put the caliper bolts in. And take a 17-millimeter wrench, and torque this bolt to 30-foot-pounds. Do the same on the top. All right. Put the wheel on, and put the lug nuts on. Now, I'm gonna torque these lug nuts to 140-foot-pounds in a cross pattern so that it tightens the wheels down evenly, and just go around and double-check.
