Kit Includes: (1) Front Driver Side Outer Tie Rod (1) Front Passenger Side Outer Tie Rod
Specification
Side Location
Driver & Passenger Side
Location
Front
Outer
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
How to Replace Outer Tie Rod 1999-2006 Chevy Silverado
Created on:
Tools used
Adjustable Wrench
Bearing Grease
Hammer
Flat Blade Screwdriver
Torque Wrench
Ratchet
Needle nose pliers
Grease Gun
1. Removing the Wheel
Loosen the lug nut covers with a 22mm socket
Pry off the center cap by hand
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
Make note of this measurement
Loosen the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
Remove the 18mm nut from the outer tie rod end
Strike the steering knuckle with a hammer to loosen the outer tie rod
Pull the outer tie rod out of the steering knuckle
Hold the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
Twist off the outer tie rod by hand
3. Installing the New Outer Tie Rod
Attach the grease fitting to the new outer tie rod
Tighten the grease fitting with a 7mm socket and ratchet
Twist the new outer tie rod onto the inner tie rod
Push the outer tie rod into the steering knuckle
Fasten the 18mm castle nut onto the outer tie rod
Push the cotter pin through the castle nut
Twist the cotter pin into place with needle nose pliers
Fill the tie rod with grease, using a grease gun
Measure the distance from the boot of the inner tie rod to the edge of the outer tie rod
This should be the same as the measurement noted in Step 2
Tighten the nut that holds the outer tie rod to the inner tie rod with an adjustable wrench
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
Reattach the center cap
Tighten the lug nut covers with a 22mm socket
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show how to replace an outer tie rod on this 2002 Chevy Suburban, and it's the same part and similar process on these Suburbans from 2001 to 2006. We show you on the passenger side, but the driver side is the same procedure. The items you'll need for this are a new outer tie rod from 1AAuto.com; 7mm, 13mm, 18mm and 22mm socket and ratchet; flat-blade screwdriver; adjustable wrench; tape measure; pliers; hammer; and a grease gun.
You want to just loosen up these 22mm caps, and then pull the hubcap free. Then, you want to loosen these lug nuts while the vehicle is on the ground, then raise the vehicle and remove them the rest of the way, unless you have air-powered tools. Then, you can do it while it's in the air.
Now you want to measure from the boot on your inner tie rod to the edge of your outer tie rod and just remember that measurement. Now, using your adjustable wrench, loosen up this nut right here, and then you want to remove this 18mm nut down here. Now just hit on your knuckle with a hammer and this is going to break up that outer tie rod and make it easier to pull out. Now just hold this nut with the adjustable wrench, pull the outer tie rod off and just twist it until it comes free. We'll fast forward as Don does this. You want to make sure that the inner tie rod doesn't spin while you're removing the outer tie rod.
Now, put the grease fitting into your new outer tie rod and just tighten that 7mm grease fitting up. Then twist the outer tie rod back onto your inner tie rod and push it down into place. Now, replace the castle nut and just tighten that up. Then push the cotter pin through and, using your pliers, just bend the ends of it. Now, using your grease gun, fill the tie rod with grease. Measure, and you should get about the same distance. That's a good preliminary alignment. You should have your car aligned after this. Tighten up the lock nut to hold it in place.
Now replace your wheel and then replace those lug nuts and tighten them preliminarily. Lower the vehicle and tighten them the rest of the way. Now torque the lug nuts in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
PSA54814
In Stock
Product Reviews
Loading reviews
5.00/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
4
0
0
0
0
Appreciated
Jacob
September 12, 2017
I like the tie rods I appreciate your business 1Aauto recommend to anyone always done me right. Great prices and quick shipping couldn't ask for no better
Danny
January 9, 2023
My order arrived on time, was an exact fit,easy work and I have done the inner tie rod's since. I recommend this product to anyone who has intermediate mechanics skill.
If you want the best ride get the best
Douglas
October 9, 2023
New tie rods for the front Suspension
Norberto
April 12, 2024
Hi I'm happy this auto parts has the best parts and really fast delivery thank you 1 A auto parts
Customer Q&A
Do these come pre-greased?April 13, 2022
John D
10
Yes, our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
April 14, 2022
Jessica D
Will these part be compatible for use on a 2wheel drive vehicle? As well as hold up on a 6 inch lift?October 7, 2022
Nathaniel R
10
These will fit an RWD or 4WD depending on the vehicle. Be sure to verify all of the information shown in the Vehicle Fit tab before ordering. These will not work for a model with a lift kit. They are intended for use on vehicles at stock height only.
October 7, 2022
Cristina P
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Cadillac is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Cadillac or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.