Our control arms are designed to be direct replacements for the original factory parts. They are 100% brand new and require no modifications for installation. No special tools are required because all of the bushings come pre-installed.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Upper Control Arm 2000-06 Chevy Suburban 1500
How to Replace Front Upper Control Arms with Ball Joint 1999-2006 Chevrolet Silverado 1500
How to Replace Front Upper Control Arm 2000-06 GMC Yukon
How to Replace Front Upper Control Arm 2000-06 GMC Yukon
Created on:
Tools used
10mm Socket
18mm Wrench
21mm Socket
21mm wrench
22mm Socket
Grease Gun
Hammer
Jack Stands
Marker / Writing Utensil
Ratchet
Torque Wrench
1. Removing the Wheel
Loosen the 22mm caps on the hubcap with the vehicle on the ground
Pull the hubcap free
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Upper Control Arm
Mark the tab on the adjustment piece with a marker to mark the alignment
Remove the two 10mm bolts holding the brake line and move the brackets
Remove the ball joint nut with an 18mm wrench
Hit the wheel knuckle and control arm to break them free
Remove the 21mm nuts from the upper control arm bracket
Jack up the wheel underneath the wheel knuckle
Remove the upper control arm nut
Remove the bolts and upper control arm bracket
Place a nut back on and use an air hammer to knock the bolt out if it won't budge
Move the control arm up and down while pulling out
3. Installing the Upper Control Arm
Put the upper control arm into place and push the 21mm bolts in to hold it
Put the brackets on either side and realign them up
Angle the control arm down into the wheel knuckle
Replace the 18mm ball joint nut
Replace the 21mm nuts from the upper control arm bracket
Replace and tighten the two 10mm bolts
Put a grease gun into place on the end of the control arm and fill it up
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
Reattach the hubcap and tighten the caps
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an upper control arm on this 2002 Chevy Suburban. We show you on the passenger side, but the driver side has the same procedure. The items you'll need are a new upper control arm from 1AAuto.com, a 10mm, 21mm, and 22mm socket and ratchet, 18mm and 21mm wrench, a marker, a torque wrench, jack and jack stands, a grease gun, a hammer, and an air hammer depending on the condition of your vehicle. After completing this procedure you will need to get a professional alignment done.
Start out by removing the hubcap. You want to remove the lug nuts. If you don't have air powered tools, you'll want to do it while the vehicle is on the ground. Loosen them preliminarily, raise the vehicle, and remove the lug nuts the rest of the way. On these brackets, you'll see a tab coming through from the upper control arm. Mark where that tab is. Remove these two 10mm bolts. Next, remove this 18mm nut, and you can see Mike uses an 18mm wrench and another wrench for some extra leverage to break it free and then removes it the rest of the way with the 18mm wrench. Hit the wheel knuckle and control arm to break them free. Then remove the 21mm nuts on either side.
Jack up your wheel, and you want to do this underneath the wheel knuckle. Remove the upper control arm nut and then remove these bolts and the bracket that's on them. Our first one pulled out no problem, this one's a bit more difficult. We tried using a hammer, that doesn't work. We tried using a wrench to help break it free, but it's in there really good. If you have this same problem, we put a nut back on it and use an air hammer to knock it out. Now that those bolts are out, you want to remove the control arm up and down while pulling out and it'll pull free.
Take your new upper control arm and push it back into place. Then push the bolts in to hold it into place. You want to make sure that you have those brackets on either side and that they're lined up. Now, angle the control arm down into the wheel knuckle. Once it's pressed down into place replace that 18mm nut. We'll fast forward as Mike tightens all of those up. Replace and tighten up those two 10mm bolts. Using a grease gun put it into place on the end of your control arm and fill it up. Put the wheel back into place and then replace each wheel lug nut and tighten them up. You want to tighten them preliminarily, lower the vehicle, and then tighten them the rest of the way. Torque each lug nut in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those lug nut caps.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
24mm Socket
Hammer
Pry Bar
Jack Stands
Trim Tool Set
Pocket Screwdriver
Locking Pliers
Pole Jack
Brake Caliper Hanger
Wheel Chocks
Cotter Pin
Ratchet
Floor Jack
Swivel
Needle nose pliers
Wire Cutters
13mm Socket
Torque Wrench
15mm Socket
Rust Penetrant
19mm Wrench
18mm Socket
Liquid Thread Locker
Brake Parts Cleaner
Safety Glasses
Pliers
21mm Socket
21mm wrench
Gloves
Copper Anti-Seize
8mm Socket
Wire Brush
22mm Socket
Tools used
13mm Socket
Torque Wrench
Hammer
Rust Penetrant
18mm Wrench
Pry Bar
Trim Tool Set
Pocket Screwdriver
21mm Socket
Pickle Fork
21mm wrench
Rubber Mallet
Flat Blade Screwdriver
10mm Socket
22mm Socket
Take the center cap off. Use a straight-blade screwdriver. Use a 22-millimeter socket. Take the lug nuts off. Pull the wheel off. These bolts are pretty rusty so I'm just going to use some rust penetrant and soak those before I start. Before we take this nut off, we just want to mark this cam right here. This is for the alignment. When you go to put this back together, you want to put this in the same location so at least it's close. You're still going to need to get an alignment done afterwards, but this will get it a little bit closer. I want to get this ABS wire out of the way, our wheel speed sensor wire. Disconnect the connector up here. Just push up on that tab, slide it out and use a trim tool. Just pull up on that retainer. You can do the same over here, and right here. Sometimes these ones break, just be careful. All right. So this piece is going to break so I'm just going to disconnect it right from the arm itself. And disconnect this right here. Sometimes you can use a screwdriver and just pop that out, or a needle-nose pliers also works. You just squeeze those together. I'm just going to put some rust penetrant on this bolt right here. Let that soak a little bit. We want to take that off next. Just remove this bracket. Use a 10-millimeter socket. Remove this bolt. It's probably going to break. Yup, it broke. Well, hopefully yours doesn't break. And slide that off.
All right. Now, we're going to take this nut off using an 18-millimeter wrench. Now I'm going to leave this nut on just a couple of threads, and then we're going to break this upper ball joint free from the knuckle. I'm going to use a pickle fork to break this free. Just slide it in, in between the ball joint and the knuckle and just give it a hit. There we go. Take the pickle fork out and just push down the upper control arm a little bit. You might need a pry bar. And take the nut off and you could slide it out. And just make sure that there's not too much tension on the brake line, brake hose. I'm going to take a 21-millimeter wrench, 21-millimeter socket. Now this is old and rusty so I just had to heat up that nut to break it loose. Normally you wouldn't have to do that. And loosen it up. That nut's pretty hot right now so I'm just going to let that cool down before I take that off. Take that nut off and see if you can pry this cam off. This is just the alignment cam. Just use a pry bar and a hammer. And just pry that off. All right. This cam bolt is stuck in there pretty good so I'm just going to use some more rust penetrant, soak it down for a while.
Here we go. All right. Get that out and do the same for the other side. All right. I'm just going to take this bracket out of the way. Just use a 13-millimeter socket and you can just slide it out of the way. Don't bend it too much. Here we go. And just use a pry bar and you can pry the arm out. And take the new control arm and just line it up. You can take a rubber mallet, or a dead-blow hammer to tap it in if you need to. And get the bolt started. And take this cam and the nut. Get the nut started. Now we tighten this up. Now we want to align that mark up. What you do is take your 21-millimeter wrench and just move the bolt on this side until that lines up. And you can snug that down. And we'll do the same for the other side. All right. Now, we're going to torque this nut to 140-foot-pounds. Do the same on the front one. Take this brake hose bracket and install that. Put the bolt back in and tighten that up. Get the nut off. Put that aside. Get this lined up with the upper knuckle. And I'll use a pry bar, just pry this down. Take the nut and get the nut started.
Now, I'm going to use a 19-millimeter ratchet wrench, while I'm using the pry bar to pry it down on the ball joint. Tighten this up. All right. Now, if you have the ability, just torque this with a torque wrench, you can torque this to 37-foot-pounds. Do the best you can. And if the stud starts spinning, you can use an allen key, that's a six-millimeter hex key. But if you use the pry bar and you just pry it down, you should be able to get that without having the stud spinning. Take this brake hose bracket and line that up. Put the nut on or the bolt in and snug it up. And take the wheel speed sensor wire and reconnect that. And then we have this holder or clip. Install that. Lock that in place. Reinstall this clip and connect the connector. And push the retainer. I'm just going to find the hole where it goes. There it is. And lock that in position. And take this fitting. Install that. Snug it up with a seven-millimeter wrench.
And take a grease gun and give it a couple pumps of grease. What you can do is look at the boot as you're greasing it, once you see the boot start to move, that's good enough. And put the wheel back up. Put the lug nuts on. Now I'm going to torque these lug nuts to 140-foot-pounds in any star pattern to tighten the wheel down evenly. And just go around again, double check. Install the center cap.
Tools used
13mm Socket
Torque Wrench
Hammer
Rust Penetrant
18mm Wrench
Pry Bar
Trim Tool Set
Pocket Screwdriver
21mm Socket
Pickle Fork
21mm wrench
Rubber Mallet
Flat Blade Screwdriver
10mm Socket
22mm Socket
Take the center cap off. Use a straight-blade screwdriver. Use a 22-millimeter socket. Take the lug nuts off. Pull the wheel off. These bolts are pretty rusty so I'm just going to use some rust penetrant and soak those before I start. Before we take this nut off, we just want to mark this cam right here. This is for the alignment. When you go to put this back together, you want to put this in the same location so at least it's close. You're still going to need to get an alignment done afterwards, but this will get it a little bit closer. I want to get this ABS wire out of the way, our wheel speed sensor wire. Disconnect the connector up here. Just push up on that tab, slide it out and use a trim tool. Just pull up on that retainer. You can do the same over here, and right here. Sometimes these ones break, just be careful. All right. So this piece is going to break so I'm just going to disconnect it right from the arm itself. And disconnect this right here. Sometimes you can use a screwdriver and just pop that out, or a needle-nose pliers also works. You just squeeze those together. I'm just going to put some rust penetrant on this bolt right here. Let that soak a little bit. We want to take that off next. Just remove this bracket. Use a 10-millimeter socket. Remove this bolt. It's probably going to break. Yup, it broke. Well, hopefully yours doesn't break. And slide that off.
All right. Now, we're going to take this nut off using an 18-millimeter wrench. Now I'm going to leave this nut on just a couple of threads, and then we're going to break this upper ball joint free from the knuckle. I'm going to use a pickle fork to break this free. Just slide it in, in between the ball joint and the knuckle and just give it a hit. There we go. Take the pickle fork out and just push down the upper control arm a little bit. You might need a pry bar. And take the nut off and you could slide it out. And just make sure that there's not too much tension on the brake line, brake hose. I'm going to take a 21-millimeter wrench, 21-millimeter socket. Now this is old and rusty so I just had to heat up that nut to break it loose. Normally you wouldn't have to do that. And loosen it up. That nut's pretty hot right now so I'm just going to let that cool down before I take that off. Take that nut off and see if you can pry this cam off. This is just the alignment cam. Just use a pry bar and a hammer. And just pry that off. All right. This cam bolt is stuck in there pretty good so I'm just going to use some more rust penetrant, soak it down for a while.
Here we go. All right. Get that out and do the same for the other side. All right. I'm just going to take this bracket out of the way. Just use a 13-millimeter socket and you can just slide it out of the way. Don't bend it too much. Here we go. And just use a pry bar and you can pry the arm out. And take the new control arm and just line it up. You can take a rubber mallet, or a dead-blow hammer to tap it in if you need to. And get the bolt started. And take this cam and the nut. Get the nut started. Now we tighten this up. Now we want to align that mark up. What you do is take your 21-millimeter wrench and just move the bolt on this side until that lines up. And you can snug that down. And we'll do the same for the other side. All right. Now, we're going to torque this nut to 140-foot-pounds. Do the same on the front one. Take this brake hose bracket and install that. Put the bolt back in and tighten that up. Get the nut off. Put that aside. Get this lined up with the upper knuckle. And I'll use a pry bar, just pry this down. Take the nut and get the nut started.
Now, I'm going to use a 19-millimeter ratchet wrench, while I'm using the pry bar to pry it down on the ball joint. Tighten this up. All right. Now, if you have the ability, just torque this with a torque wrench, you can torque this to 37-foot-pounds. Do the best you can. And if the stud starts spinning, you can use an allen key, that's a six-millimeter hex key. But if you use the pry bar and you just pry it down, you should be able to get that without having the stud spinning. Take this brake hose bracket and line that up. Put the nut on or the bolt in and snug it up. And take the wheel speed sensor wire and reconnect that. And then we have this holder or clip. Install that. Lock that in place. Reinstall this clip and connect the connector. And push the retainer. I'm just going to find the hole where it goes. There it is. And lock that in position. And take this fitting. Install that. Snug it up with a seven-millimeter wrench.
And take a grease gun and give it a couple pumps of grease. What you can do is look at the boot as you're greasing it, once you see the boot start to move, that's good enough. And put the wheel back up. Put the lug nuts on. Now I'm going to torque these lug nuts to 140-foot-pounds in any star pattern to tighten the wheel down evenly. And just go around again, double check. Install the center cap.
PSA83675
In Stock
Product Reviews
Loading reviews
5.00/ 5.05
5 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
0
0
0
0
Great Price and Identical fit
Elwyn
April 22, 2017
I installed the new control arm and it enhance my driving experience back to the factory standard. Don't need anything but I am checking for more parts to purchase from you guys. Your service is always timely and on time. And your how to videos really save me time and money. Thank you 1aauto for your dedicated service in making my time for repairs a pleasant experience.
Very satisfied fast delivery and good part
M
July 7, 2018
This is the first time i have ever ordered from A1. I am very satisfied with their service I received the part in 3 days and it was an excellent quality part I ordered a upper control arm with ball joint. I would definitely order from them again and would recommend them to anyone
overall
K
November 12, 2018
great fit and the delivery was fast and it came with ball joints pressed in ready to go
Best Value!
B
February 22, 2019
Exact fit. Easy to order and fast shipping!
Better price tan I expected
S
April 5, 2019
The sales person was very helpful. Her knowledge of the parts for this job were very good. The part was in stock and the price was better than I expected.
Customer Q&A
What are the torque specs for the front upper control arm?October 2, 2016
Rowdy B
10
I don't think you have to torque them. Just make sure they are tight because you will need to take it for an alignment after. That's what I did anyway
October 2, 2016
Micah L
10
I'm not sure of exact spec. But I just tightened them to snug because you are supposed to get a alignment done when replacing this part.
October 2, 2016
Maurice S
10
Please call the dealer or obtain a Chilton or Haynes repair manual for these specs. It may carry depending on what model and GVW rating you have
October 4, 2016
Brian F
10
It varies by vehicle. On my 2000 Gmc Yukon the knock sensor's torque is 15 ft-lb.
April 22, 2017
Elwyn T
I have a 6in lift kit and a 3in body lift can I get more powerful sway bars another steering suspension bars sway bars ball joints tie rods?January 23, 2022
Demetrio M
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Chevrolet is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by Chevrolet or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.