2004 Cadillac Escalade Front Ceramic Brake Pads TRQ BFA73066

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Don from 1A Auto. I hope this how-to video helps you out, and the next time you need a part for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the brakes on this 2002 Chevy Suburban. The items you'll need for this include a new brake pad and rotor kit from 1AAuto.com, an 18mm and 22mm socket and ratchet, a piece of pipe for extra leverage, a T55 Torx bit, a large C-clamp, a torque wrench, a wire brush, jack and jack stands, brake cleaner, and brake grease.

You want to just loosen up these 22mm caps, and then pull the hubcap free. Then you want to loosen these lug nuts while the vehicle's on the ground, then raise the vehicle and remove them the rest of the way, unless you have air powered tools, then you can do it while it's in the air, and then just remove the wheel. You want to check for any deep groves in your rotor. You want to check in here for the life of your brake pads and over here for the life of the other one. You can see ours is actually in decent shape.

There's two T55 Torx bolts that you need to remove. We'll fast forward as we use a T55 Torx bit and a ratchet to remove those. Then, using a large C-clamp, just put it back behind the caliper here, and the other part right here on the brake pad, and just twist this in. This is going to push your caliper piston in and make it easier to pull the caliper off. Just remove the C-clamp and lift your caliper up and off and set it aside. Using a flat blade screwdriver, just pry out your brake pad. Sometimes the brake pads can be stuck in there. Use a flat blade screwdriver and a hammer to pry it free. You want to remove these two 18mm bolts on your caliper bracket.

You can see we use a piece of pipe for some extra leverage, here. We'll just fast forward as he breaks the other one free and removes both of these bolts. Now, slide the rotor off. On the left is the old rotor and brake pads, on the right are the new ones from 1A Auto. You can see they're identical and they'll fit exactly the same.

Spray your new rotor with brake cleaner and just wipe it down. Do the same thing to the back. Now, apply brake grease to the tabs on either end of your brake pads. Using your wire brush, just clean up those brake slides on your caliper bracket. Push your rotor back into place and then twist on a lug nut. This will hold the rotor in place. Turn the wheel and put the caliper bracket back in to place. Replace those two 18mm bolts. We'll fast forward as Don does this and tightens both of those up. Torque both of these to 75 foot-pounds.

Push your new brake pads into place. Use a hammer if necessary to lightly tap that into place. Using an old brake pad, just put it onto the caliper pistons and then tighten it in with your C-clamp. This will just push those pistons in the rest of the way. Grease up your caliper bolts. Out the caliper back into place and slide those slide bolts back in. We'll just fast forward as Don tightens those up. You'll want to tighten these to about 30 foot-pounds.

Now, replace your wheel and then replace those lug nuts and tighten them preliminarily, lower the vehicle, and tighten them the rest of the way. Torque the lug nuts in a crossing pattern to 100 foot-pounds. Replace the hubcap and tighten up those caps. After doing work on your brakes, you want to pump the brake pedal until it firms up and then try a stop test from five miles per hour and ten miles per hour, and you're all set.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.

In this video, we're going to show you how to replace the front brakes on this 2005 GMC Savana 2500. It's a similar process on the Chevy Express. The items you'll need for this is a new break set from 1A Auto, 18mm, 21mm, 22mm socket and ratchet, a breaker bar and a piece of pipe for leverage, a flat blade screwdriver, penetrating oil, a hammer, large C-clamp, white grease, torque wrench, and jack and jack stands.

Start off by removing the wheel cover or whatever wheel trim you might have. This one has a chrome one. Pull that off, and then just use your socket and pull or loosen the lug nut covers. Pull the center cap off. If you don't have the benefit of air tools, you want to loosen the lug nuts with the vehicle on the ground, then jack up and secure the vehicle. Then remove the lug nuts, wheel, and tire.

Turn the wheel so that you can get to the brake. On the back of the caliper, there's two 18mm bolts. You just want to remove these. It can be a little difficult, so it helps to use a piece of pipe for extra leverage. We're just going to fast forward as he removes this.

The next step, you want to use a flat blade screwdriver to just pry the brake pads away from the caliper, and it will allow you to pry off that caliper. Just keep using the flat blade screwdriver, top and the bottom, you could see he's just going back and forth until, eventually, it will come off. You just want to set that aside.

Now, using the flat blade screwdriver, you just want to pry out your brake pads. Now on some vehicles, it's going to be more difficult than on others. It depends on the condition of the brakes. In this case, it takes just a little effort, and if you have to, you can use a hammer just be careful not to damage or bend anything. We're just going to fast-forward a little bit as he removes those brake pad slides.

There are two 21mm bolts back here that hold on this caliper bracket. Ours are a little rusted, so we spray them with some penetrating oil first, just to loosen them up and let that sit for a second. Then, using a breaker bar, and, actually, a piece of pipe for extra leverage, we just remove those bolts, and we're just fast-forwarding here as he does that. When you remove those bolts, the caliper bracket will come right off.

Now, you just want to take a hammer and hammer the back of that rotor. Just keep turning it and hammering the back of it, and it's going to come off. With the old rotor; the new rotor. New pads; same size. With this caliper guide, you can replace these boots . If they're torn, you pull them out and you push them in. The most important thing about the brakes here, what we found was the pedal was soft, it didn't feel like they should, and you'll notice that when these were sliding or weren't sliding and getting stuck on this corroded brake slide hardware, you know it's the new parts, allow the pad to slide just it should when they're new.

Now we're just cleaning up the new rotor real quick. What you want to do is you want to take some white grease and just put it on the clips of these new brake pads. Then, using a flat blade screwdriver, just scrape some of the corrosion on that caliper bracket. This will just help those slides to clip back on. Now, what you want to do is just clip those slides on, and as Don was saying: "They make a difference." New ones are definitely worth it and 1A Auto does sell these. This just clips right into place. We'll just push them down.

Now, what you want to do is just reset the pistons in this caliper. What you want to do is take one of your brake pads. If you're changing them, you want to use one of the old ones, and you want to lay it across these two pistons. Then, using a large C-clamp, as you tighten the clamp, that paddle push those pistons back in and reset them, as you can see here. Now they're reset.

Now we're just going to put on our brand new rotor, and once you get it into place, you just want to put one of those lug nuts on, and it will just hold it into place. We put the rest of the brakes together. Now you can put your caliper bracket back on, and, to place those bolts, you want to just do them first by hand. Then, once you get them lined up and both them in place, you can use a socket and ratchet to tighten them the rest of the way. Now you want to just torque those bolts to 100 foot-pounds.

Now you can put your brake pads back in. Now, for these caliper pens, what you want to do is you want to clean them off a little bit, and then put some white grease on them, this will help them so that they slide easier.

What you want to do, pull down your caliper and just fit it into place. Now you can see up here, you want that little gasket there to go in and you can slide your bolts back in. We'll fast-forward here as he tightens those up with a socket and ratchet. Torque these bolts to 100 foot-pounds. We're just going to fast-forward here as you remove that nut, put the wheel into place, and you just want to replace all those nuts and tighten them in a crossing pattern.

Again, if you don't have air tools, you just want to lower the vehicle and tighten those the rest of the way on the ground. Then you want to torque those lug nuts to 100 foot-pounds. Before actually driving the vehicle, you want to pump the brake until they're firm, and then you want to do a test, stopping from 5 mph then 10 mph.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.

Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.

Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.

In this video we are going to be showing you how to replace the rear brakes on this 2002 GMC 2500 HD, same as a Chevy as well, same as 2000 to 2007 both GMC and Chevy 2500 HDs. Tools you will need are 18 and 22mm sockets with your ratchet, and a breaker bar and pipe for more leverage. I also do show you a way to get leverage with an 18mm wrench and an additional wrench to hook to it, large regular screwdriver or small pry bar, a large hammer, small and small stubby regular screwdrivers, also a brake spoon for that part of the video would work, wire brush, bearing grease, small hammer and of course jack and jack stands.

Start out by removing your wheel. Carefully remove the plastic retainers and your center cap and then if you are working with hand tools you want to start with the vehicle on the ground, loosen the lug nuts, then raise it up and secure it, and then remove the lug nuts. I have the benefit of air tools here, so I removed the lug nuts and removed the tire.

So taking a closer look at our brakes, you can see our discs are really deteriorating here, so we are going to replace those, and you can see right in there, that pad, we had a little bit of life left and the other one looks like it's got more, but obviously we are going to replace the pads as well.

So to remove the calipers, here, what we are going to do is we are going to undo this 18mm bolt here and then the same one down here, an 18mm bolt. These are Torx screws, but this top one is very difficult to get to, so what we are going to do is we are going to take the bolts off and remove the whole caliper bracket and everything first. Before you unbolt it, what you can do is take a large screwdriver. I have a breaker bar here. Feed it right into this hole here and pry out and that forces the pistons back into the caliper. There is somewhat limited room here, so I put my 18mm wrench on there, take another wrench which gives me a little extra leverage, and if you have a breaker bar and a socket available then you can usually fit those in there as well. I am just showing you this as an alternative method. I can remove this bolt and it comes right off. The lower one is easier to get to so you can use the ratchet or breaker bar, or anything, or air tools. I will finish getting this out and you can bring the caliper up like that. I am going to fast forward here. Basically once you pull that bracket up, you just have to force the shoes down through the bracket and the biggest thing is there are little wear tabs that will get caught and you just make sure you bend those wear tabs in and the shoes will go down right through the bracket and you can pull the bracket right off.

Now, what we have here is we got our caliper. I got a big C-clamp and one of the old pads, so I am going to work this caliper with the C-clamp and push those pistons back in and I am going to wipe down these slide bolts. They look like they are in nice shape. Clean up the sticky stuff on them. Put on a little bit of new bearing grease. Make sure they're moving well.

Now I move this caliper, it's got a couple little locks to hold it on. You can either break these off or twist them off. They come off easily enough. Now I am just going to coat this with some penetrating oil. I already know my rotor is in tough shape, so I am not going to worry too much about hurting it, when I get them off. It actually came off really easily. You can hit it right back here where your caliper was and I have open space.

You saw my rotor come off really easy, but that is not always going to be the case. Sometimes your emergency brake might be adjusted so that the rotor doesn't come off very easily, so the first thing you might want to do is to have a short screwdriver, so I am talking with the rotor still on, you reach back here and you can see I am pulling that plug out. What you are going to want do is take another screwdriver or a little bit larger, but still a small screwdriver and go through the back side until you feel this wheel and then you are going to turn the wheel star down, which is bringing the screwdriver up, and that will basically loosen your emergency brake so your rotor will come off easier. So I have used some mineral spirits, and I've cleaned off my shoes for my emergency brake and I see that I got some oil on there and that probably means I've got bad axle seal, but this truck got 240,000 miles on it, so I am not that worried about it. I am going to use some anti-seize here. I'm probably never going to have to get this off again, but if I do have to get it off again now I know I can.

The new rotor from 1A Auto is in a lot better shape than the old one. It goes right on. I lightly secure with a couple of lug nuts and now I am going to take my small screwdriver, go in to the backside and tighten up the emergency brake adjuster, basically until I start feeling it give some friction to the wheel. I am going to fast forward through this. You do want to go on this side with the handle of your screwdriver up and then move it down, which moves the wheel up inside the rotor and it is kind of trial and error. Sometimes you can move it one way and you don't tighten it and then move it the other way and you do tighten it. It takes a little longer, but adjust them until you have good friction from the shoes and then make sure you replace that rubber dust plug.

Here is my bracket for my brake shoes and what I am going to do is just take these stainless steel slides with a wire brush on them and clean them all up. Get all this dirt off of them. Here are new pads from 1A Auto. You can see a little bit more life then the old pads that were on there. So we got our caliper with slide bolts cleaned and well-greased. This can be the problem with these trucks if these dry out and get dirt in them or whatever, the calipers actually seize up and your rear brakes do not even work, so if that the case you may want to replace these slide bolts, but you definitely want to get them out, clean them up and if you have to wire brush them and make sure you get a good amount of grease back on them. I've got my shoes right there. What I am going to do is take my bracket and just put a little tiny bit of that penetrating oil and that is not really going to make it slide, it is just to make it easier to get together. Put my brackets down on to the slide bolts, then into the shoes. Use a small hammer and looking at these carefully, make sure that the wear tabs go through correctly and also that your shoes are in the right spot here. It's just out there. Okay, that shoe is on. It may benefit you to take like a screwdriver or pry bar and just kind of, the shoe is getting stuck here on this slide a little bit. Push it into place and then lower it, and it looks like it could go in a little bit, push them into place a little bit and then it goes down on. You might have to shake it around a little bit before it goes in towards that bolt. Do the same down here. Get the lower bolt started and take out my lower bolt a little bit with the air wrench. I cannot really get a torque wrench down here, so I am going to just put my wrench back on here and tighten this up really good and it should be tightened to about 120 foot-pounds. We will use a torque wrench.

I am going to speed it up here as I remove those two lug nuts, then put the wheel on, hand thread my lug nuts at first, then use my air wrench just to tighten them up a little bit. Very important: you want to make sure before you test drive the vehicle you pump the brakes a bunch of times then make sure it stops from like five miles an hour and ten miles an hour before you road test.

Here again, fast forward as I have now put the vehicle on the ground and I am torquing the lug nuts to 120 foot-pounds using a crossing pattern and then I actually go around one-by-one afterwards just to check and make sure that they are all torqued, and then put your cap on and hand tighten the plastic retainers.

We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.