Replaces
Replaces Chevrolet GMC Hummer Front Driver & Passenger Side 2 Piece Wheel Bearing & Hub Assembly Set Timken TKSHS00407
$554.24
Replaces Chevrolet GMC Hummer Front 6 Piece Drivetrain Kit TRQ PSA27243
$529.95
Replaces Chevrolet GMC Hummer Front 14 Piece Steering & Suspension Kit TRQ PSA34564
$512.95
Replaces Chevrolet GMC Hummer Front 13 Piece Steering & Suspension Kit TRQ PSA65894
$493.95
Replaces Chevrolet GMC Front Driver & Passenger Side 2 Piece Brake Rotor Set ACDelco ACBFS00451
$449.95
Replaces Chevrolet GMC Rear Driver & Passenger Side 2 Piece Brake Rotor Set ACDelco ACBFS00822
$445.95
Replaces Chevrolet GMC Hummer Front 10 Piece Steering & Suspension Kit TRQ PSA65893
$440.95
Replaces Chevrolet GMC Rear Ceramic Performance Brake Pad & Rotor Kit TRQ Performance BKA21266
$423.95
Part Details
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Install Tip: You may be required to reset the vehicle computer after installation of this part.
Quality Tested - built to a strict level of product standards.
Item Condition:
New
Attention California Customers:
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Returns: Parts with electrical components cannot be returned once installed.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Hi, I'm Mike with 1A Auto. We've been installing auto parts for over 30 years!
What's up, guys? I'm Andy from 1A Auto. Today I'm going to show you how to remove and reinstall the mass air flow sensor in this 2008 Chevy Silverado. If you need parts for your vehicle, click the link in the description and head over to 1aauto.com.
I'm going to take an eight millimeter socket and extension in a ratchet. You could also use a straight-blade screwdriver. I'm going to loosen up these two worm clamps right here, loosen that one up, and then also loosen this one up. Set that aside. Before I take that off, I'll disconnect the connector. Just push down on the lock tab, slide it up, and you can grab the snorkel and just wiggle it back and forth. Pull that off like that, and grab the mass air flow sensor, slide it off like that, and there's the mass air flow sensor.
I'm just going to take this rubber gasket off of this clamp, just grab it right here, slide it off, set that aside, and we're going to transfer that to the new one.
Here we have the old mass air flow sensor. Here we have the new mass air flow sensor from 1aauto.com. As you can see, the shape is the same. The arrow is pointing in the same direction. If you look at the connector, the connector is the same. It has the same screen on the backside, and the internals look the same or very similar. Get yours at 1aauto.com, and you'll be ready to rock and roll.
I'm going to take this clamp, this rubber seal, and we're going to install that. This little tab right here lines up with this right here, so I'll slide that into position just like that. And we want to remember the way the air flow goes in that arrow, so just slide this right here. There's two little tabs right here that line up with this tab, get that into position. This does help if you do pull the dipstick tube out a little bit to just take that out of your way. Line this hose up just like that.
Before we tighten those down, I'm just going to connect our electrical connector. Just connect our electrical connector right here and lock it in place. I'll take a straight-blade screwdriver. You can use a straight-blade screwdriver or an eight millimeter socket and ratchet. Just snug that up, and then I'll self-snug this one up, and that's good. If you pulled the dipstick out, reinsert that into the tube.
Thanks for watching. Visit us at 1aauto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
