Replaces
Part Details
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the rear inside door handle on this 2002 Sierra Crew Cab, same as any '99 to '02. The 03 and up are a little different, as far as taking the panel off. The only tools you'll need are a flat blade screwdriver, a 7mm socket, and a 10mm socket with a ratchet and extension.
There are two 7mm screws that you have to remove, or bolts: one right in there, and then one down in the bottom corner here. As well, you need to pry out this trim panel, pry out your lock button, and pry out your window switch and disconnect it. First, put your finger under, and pull out that bezel. Use a regular screwdriver, just to get the front there. Pull off your lock button and the switch. Also, pry up gently, there on the front of it, and then there's a little tab. Get your screwdriver, push on it, pull the connector down and out. You can also pry out your light and reflector, and disconnect it. Use your 7mm socket, ratchet and extension. We'll just speed up here as we remove those two 7mm bolts. Once that's unbolted, then you just lift up on your panel and it comes off.
You can see, your handle's right here, there's a little clip that goes on this rod. Either get your finger in there, or a screwdriver, and pop that clip up and off, and get that rod out. Get a 10mm bolt right here, then your handle comes forward and out.
Put it in, push it against the door, slide it back, get your rod in, get the clip off. Put this bolt back in. Put your door handle back on. Make sure you bring this right up to here, bring your courtesy light through. For the white plastic legs right there, get them resting in the door like that. Push the panel against the door. It should slide down nice and easy. Put in this bolt next to the armrest. I put that in backwards.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the rear outside door handle on this 2002 GMC Seirra Crew Cab, same as a Silverado as well as the same as the rear doors on Suburban. The only tools you'll need are flat blade screwdriver, a 7mm socket, a 10mm socket and then a ratchet and extension.
There are two 7mm screws that you have to remove or bolts: one right in there and then one down in the bottom corner, here. Then, as well, you need to pry out this trim panel, pry out your lock button and pry out your window switch and disconnect it. First put your fingers under it. Pull up that bezel. Take a regular screwdriver stick in the front there, pull out your lock button and on this switch, also pry up gently there. In front of it, there's a little tab. Use your screwdriver, push on it and pull the connector down and out. You can also pry out your light and reflector and disconnect it. Take your 7mm socket and ratchet and extension. We'll just speed up here as we remove those two 7mm bolts. Once everything is unbolted, then you just lift up on your panel and it comes off. Peel your water shield carefully, and pull it back some.
Now inside there's a rod that runs up to the door handle here and you can easily just use your thumb to push that clip off. Disconnect the rod and there's three bolts: one there, one there and then one that's a little bit more difficult, right up in there. For two of them, use a 10mm socket with a ratchet and extension. We'll just speed it up here as I take those two nuts off that are pretty easy to see. Then take my extension off and put my ratchet right up in. We'll speed it up here again as I take that nut off. Take that, and now, your handle pulls right out. You can see this is rusty. What happens is this breaks or sometimes this pin breaks.
Here's my original handle and a new handle from 1A Auto. You can see it's all the same. It doesn't hurt if you want before you put it in, to spray it with some penetrating oil or white lithium grease. You can see that this gets pretty corroded and gets sticky especially if you don't use the doors a lot and that's how the handle can break. The new handle just installs like the old one came out. Put it right in. Use your original nuts. We'll just speed it up here as I start those three 10mm nuts and then use my socket, ratchet and extension to tighten them up. You want to tighten them up firm; they don't have to be extremely tight, though. Reach up in there, connect the rod back into place. Put the clip back down.
Put your plastic water shield back into place. Put your door handle back on, make sure you bring this right up through here, bring your courtesy light through. The white plastic legs down there, get them resting in the door like that. Push the panel against the door. It should slide down nice and easy. Get this bolt next to the armrest. I just put that in backwards.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Tools used
Okay, friends, to get started on this handle, it's gonna be very simple. We're gonna remove this mounting bolt right here and this one right here. To do that, you'd use a socket that looks just like this, it looks like a star. It's a Torx bit. You want a T30. There's our first bolt, and our second, and there's our handle. Once you've compared your new handle to your old and you know everything matches up perfectly, it's time for the install. This right here goes down along the bottom. Let's put it right in there. Start in both of the bolts and then we'll snug them up. Okay. Let's test it. It's definitely latched. Perfect.
