Replaces
Part Details
TRQ brake kits are designed to restore your brake system to like-new performance. TRQ brake pads are positive molded, thermal scorched, chamfered, and utilize a multi-layer shim for enhanced performance and service life. TRQ rotors have a non-directional finish that reduces the break-in period for new rotors as well as reducing vibrations throughout the rotor’s lifecycle. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Gonna take the center cap off, use a straight blade screwdriver. Take that off. Use a 22-millimeter socket, take off the lug nuts. Take the wheel off. Take these two caliper bolts out. I'm gonna use a 12-millimeter socket and then a 16-millimeter wrench just to hold the slide from spinning. Loosen these up.
Now just use a screwdriver, pry the caliper off. Pull it out. And you can use a caliper hanger and just support it from the upper control arm right there. Just make sure there's no tension on the hose. Slide it over here. Take the brake pads off. Just use the same straight blade screwdriver. And take an 18-millimeter socket, take these 2 caliper bracket bolts out. Take these bolts out and slide the bracket right off.
I want to separate the bracket from the caliper. I'm gonna use a 12-millimeter socket. Take these two bolts out. Now, before we put these anti-rattle clips or brake pad clips on, just use a little brake grease. Just put it right there. That's just gonna prevent some corrosion on the caliper bracket. You can put the clip down and give it a nice thin coat right on top. Do the same for the other side.
And take the caliper bracket, slide it in position. Take the caliper bolts, get those started. You can put some thread-locking compound on them. Now I'm gonna torque these bolts to 122-foot-pounds. Now take the brake pads with the wear indicator facing to the top, slide those in position.
Now we're gonna install this clip on the caliper itself. Just line it up. This piece goes towards the inside and just slips in like that. That looks good. Now take the caliper and line the caliper up. Get the bolt started. Now I'm gonna use a 16-millimeter wrench to prevent the caliper slide from spinning and then tighten this bolt to 31-foot-pounds. Do the same on the top one.
Now we want to top off the brake fluid before we attach the lines or even disconnect the lines because we don't want this brake fluid to go too low, or then it's going to be harder to bleed the system. And take the cap off, wipe it off first with a rag. Make sure you use the appropriate brake fluid. I'm just gonna top it off all the way to the top. That's good. Now we'll just put the cap back on.
Now, if you were not going to replace the brake hose when you're replacing the caliper, you would take this bolt out right here, the banjo bolt, and you're gonna replace the two gaskets on there. You're gonna use an 11-millimeter socket to take those out, put 2 new gaskets on, and then attach it to the caliper. We're gonna replace the hose in our video.
Now, take this cap off of here, take your banjo bolt with some new washers on them or gaskets, copper gaskets. Line this up. And then we're gonna torque this banjo bolt to 30-foot-pounds. Now I'm gonna take the cap off the bleeder right here. Just use a pick or something or even a little screwdriver. And make sure you have a drain bucket underneath or something to catch the fluid and we'll loosen up this bleeder screw. I'm just gonna let it gravity bleed first. Now, take your cap off. Double-check your fluid level before you bleed it, top it off. Now we had the brake line off for about 10 minutes. I only lost about that much fluid, which isn't too bad. So it only went down a little bit. So if you had to go about 10 minutes, that's probably acceptable. Put the cap back on. Now, the fluid started coming out of the bleeder, so it's gravity bled. I'm gonna use a 10-millimeter wrench, snug this up, and then if you have any other calipers or brake hoses to replace, now you can move on to the next one. Do all those before you perform a complete brake system bleed.
Now pump up the brake pedal, just go slow. So the pedal is still very spongy. Now what we're gonna do is hold the brake pedal down and open the bleeder up. So it's someone else pushing down on the brake pedal. Go ahead, push it down. When it's holding, I'm gonna open up the bleeder slowly. You're gonna see some air bubbles come out, then I'll close it, then I'll say, okay, you can let up, and then push it down again and have them hold it, open it up, more air bubbles came out. Let up. And hold it. Some more air bubbles came out. And doesn't look like there's any more air. So I can close this one up, tighten that, put the cap back on, just spray this area down with some brake parts cleaner and move onto the next wheel. Now you want to double-check your brake fluid level. Just use a rag, wipe it down, give it a shake. And there's a max line and a min line. Double-check it. Looks good. Adjust accordingly.
If for any reason before you were bleeding the brake fluid or before you were replacing the calipers, if the fluid level got below the master cylinder, you're gonna need to do an automated bleed afterwards. You're gonna need a scan tool and a pressure bleeder. But if you had the fluid up to par, you should be all set.
Reinstall the wheel. Put the lug nuts on. Now we're gonna torque these lug nuts to 140-foot-pounds in a star pattern to tighten the wheel down evenly. And just go around again, double-check. And reinstall the center cap.
Tools used
We're gonna start by taking the wheel off. I'm gonna use a 22-millimeter socket. Take off all the lug nuts. And take the wheel off. Now, we can take these caliper bolts out. I'm gonna use a 12-millimeter socket. Loosen those up. And if the caliper slide is spinning, you can use a 17-millimeter wrench to hold it while you take the bolt out. Now, you can grab the caliper. You might want to rock it back and forth a little bit. That'll compress the piston a little, make it easier to slide off.
And then, you can use a brake caliper hanger, and just hang it from the upper control arm, or you can hang it from the coil spring just like that. Just make sure there's not any tension on the brake hose itself. Now, take the brake pads off, just slide them out of the way. Now, we're gonna take the bracket off. You need to take these two bolts out, use an 18-millimeter socket. Loosen these up. And then, grab the bracket, and just slide it off. Now, you're gonna take the rotor off, just grab it and slide it.
If it's stuck on there, you can take a hammer and just hit in these locations. It's stuck on the parking brake a little bit. Just try to wiggle it. You can just take a prybar and try, and pry in here a little bit. It should get this off. All right. I'm just gonna take two screwdrivers, just try to wiggle this back and forth. There we go, slides right off. Before you put the new rotor on, just take a wire brush, and just clean up some of the rust right here. You could also use a die grinder, and just don't sand down too much. Just get some of the rust off.
Now, you're gonna install this rotor backwards first. Take a little brake parts cleaner, just clean off the backside, and flip it around, and slide it over the parking brake. If you have to adjust the parking brake, you can adjust it right there. And then, spray this side with brake parts cleaner, and wipe it down with a rag. Now, you're gonna take a wire brush, and just clean up this bracket. If you're gonna reuse these clips, just clean these up. If not, take them off.
Just clean up some of this rust right here. Do the same with the other side. And then, just take some brake caliper grease, and just put a nice, thin coat right here. Same on the other side. And then, take these pad slides, and do the same. Put on a nice, thin coat. And then, take these pad slides out. The slide pins. Take a little break parts cleaner and a rag. Just wipe these off. You can clean this out with brake parts cleaner as well. Wipe that down.
Take a little brake caliper grease, and just reinstall it, and do the same with the other side. Now, take the caliper bracket, and line it back up. Brake caliper bolts, get those started. Now, I'm gonna torque these bolts to 122-foot-pounds. Now, I'm gonna put the brake pads on. Now, the warning indicators are gonna go to the top. So, on the inboard pad goes at the top and same with the outboard pad. Just slide them into position. That's good.
Now, I'm gonna take the brake caliper off the hook. Now, I'm just gonna take the old brake pads and a caliper compressor tool and just compress the pistons. You need to push them back into the caliper, and just slowly compress it. You don't want to do it too fast. It's just gonna push the brake fluid through the hoses, through the lines, back up to the master cylinder, and into the reservoir.
All right. That's good. Fully compressed, and just slide it over the brake pads. Put the caliper bolts in. And take a 17-millimeter wrench, and torque this bolt to 30-foot-pounds. Do the same on the top. All right. Put the wheel on, and put the lug nuts on. Now, I'm gonna torque these lug nuts to 140-foot-pounds in a cross pattern so that it tightens the wheels down evenly, and just go around and double-check.
Tools used
