Replaces
Part Details
Product Features
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories. Shipping is not available to Canada.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories as well as P.O. Boxes and APO/FPO/DPO addresses. Final shipping costs are available at checkout.
Created on:
Tools used
This video is brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
In the Chevy GMC Truck Grille Replacement, you'll need a Phillips Screwdriver, a 7mm Wrench, 7mm Socket with extension and ratchet and a 1/ 2 inch wrench.
You begin by removing the four screws that hold in the parking light and we'll speed up the video here for you a little bit. Once those screws are removed, then you pull the parking light out and there's thumb tabs that click and the lights twist out, and your parking light is removed.
After the parking lights removed, you're going to just reach in, twist and pull out the side marker light. Now, you're looking for 10 screws that hold in the grille, one there, one there, two in the middle on lower, there and one there. Then on the other side behind the other parking light which you first removed obviously, there and there, and then on the top. Two on each side basically, right up near the radiator, there, there and there.
Once these 10 screws are removed, then it's pretty simple, you can just lift up, pull out, make sure your lights are clear, that also pig tail on here to make sure that that's free and not catching on anything, and you're grille's out.
Once the grille's out, then you're going to remove your side marker light and reflector with the two inch nuts right there, then two for the reflector. Then, there's a small valance, that's the color of your truck that actually just clips on to the bottom of the grille, and it removes very easily just by pressing on the tabs. You don't need any tools and it just comes right apart like that. Then, you clip that on to your new grille and install your side marker light and reflectors on to the new grille and you're ready to reinstall.
Reinstallation is basically reverse of the procedure. Pull the lights through there, make sure nothing gets caught up in there and don't want to pinch any of those harnesses or lights or anything. There's also a small harness in the middle, make sure it doesn't get pinched in there. Once you line up the close up panels on the side, just make sure things are lined up on the side. Make sure it's going on there correctly, and then check the other side and you should be able to just push the grille into place without too much trouble.
Once it's in place, then you reinstall the 10 bolts that hold it on and go from there. Now, we reinstall those bolts and now, we need to plug the side marker lights back in and then reinstall the parking lights. First, the side marker light, you just push it into the hole and twist, and then the parking light.
Again, plug the lights in and twist to lock them in place, and then your four Phillips screws hold that in. We'll speed up the video again here just to get through it. These screws should be put on tight but not too tight because it is a plastic lens, you don't want to break the edge of the lens. Okay. Once that's done, you're all set. Your grille's been reinstalled.
This video is brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Thank you very much.
Tools used
Hi, I'm Mike from 1AAuto. We've been selling auto parts for over 30 years! We're dedicated to delivering quality auto parts, expert customer service, and fast and free shipping, all backed by our 100% satisfaction guarantee. So visit us at 1AAuto.com, your trusted source for quality auto parts.
In this video, we're going to be working with our 1996 GMC Sierra. We're going to show you how to remove and replace your vehicle's turn signals. If you like this video, please click subscribe. We have a ton more information on this and many other vehicles. And if you need these parts for your truck, you can follow the link down in the description over to 1AAuto.com.
Here are the items you'll need for this repair.
Remove the four Phillips head screws on the outside edges of your turn signal. We'll do this using a Phillips screwdriver. Once the screws are out, you can pull the housing forward. Remove the electrical connectors. Repeat these steps on the opposite side.
Here we have our turn signals that were removed from our vehicle, and our parts from 1AAuto.com. As you can see, these parts are exactly the same, with the same housings and lenses. Back side has the same openings at the bulb sockets. And we have the same four bulb mounting location. You could see the old ones really fogged up. They're not going to let a lot of light through. They don't look good. These new parts are nice and clear, nice and bright. They're going to get that light through so other people can see what you're doing and update the front of your truck. They'll go in direct fit, just like your original equipment and fix you up right.
Reinstall the lights into the turn signals. Install them into the grill, along with the four Phillips head screws. Repeat these steps on the opposite side.
Thanks for watching. Visit us at 1AAuto.com for quality auto parts, fast and free shipping, and the best customer service in the industry.
