Kit Includes: (2) Front Sway Bar Links (2) Front Outer Tie Rods (1) Idler Arm (2) Front Upper Ball Joints (1) Pitman Arm (2) Front Inner Tie Rods (1) Idler Arm Bracket Assembly
Specification
Steering / Suspension Option
with 3 Groove Pitman Arm
Location
Front
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Application Specific Design: No modifications necessary
Anti-Corrosion Coated: Enhanced surface life
Pre-greased: No additional maintenance required
Kitted for Restored Performance: Improved road-feel and handling
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How To Replace Tie Rod 2003-13 GMC Savana
Created on:
Tools used
Adjustable Wrench
21mm Socket
A Piece of Pipe (for leverage)
Hammer
Torque Wrench
Jack Stands
7mm Socket
Ratchet
Floor Jack
Needle nose pliers
1. Removing the Wheel
Pry off the wheel cover by hand
Loosen the lug nut covers with a 21mm socket
Pull off the center cap
Loosen the lug nuts with the vehicle on the ground
Raise the vehicle with a floor jack
Secure the vehicle on jack stands
Remove the lug nuts
Pull off the wheel
2. Removing the Outer Tie Rod
Turn the brake rotor by hand or turn the steering wheel to turn the rotor
Loosen the tie rod with an adjustable wrench
Straighten out the castle nut pin with pliers
Remove the pin
Remove the 21mm castle nut from the ball joint
Strike the wheel knuckle with a hammer to loosen the tie rod end
Pull the tie rod out of the wheel knuckle
Measure the distance from the base of the inner tie rod to the end of the outer tie rod
Note that measurement
Twist off the outer tie rod
3. Installing the Outer Tie Rod
Twist the outer tie rod onto the inner tie rod
Measure the distance from the base of the inner tie rod to the end of the outer tie rod
This should be the same as the measurement from Step 2
Push the ball joint into the steering knuckle
Fasten the castle nut onto the ball joint
Push the pin through the castle nut
Bend the pin into place with pliers
Tighten the tie rod with an adjustable wrench
4. Reattaching the Wheel
Slide the wheel into place
Start the lug nuts by hand
Tighten the lug nuts preliminarily
Lower the vehicle to the ground
Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
Reattach the center cap
Tighten the lug nut covers with a 21mm socket
Push on the wheel cover
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an outer tie rod on this 2005 GMC Savana 2500. It's the same process on the Savanas from 2001 to 2006, as well as a large variety of GM trucks and vans. The tools you'll need are an adjustable wrench, a piece of pipe for leverage, a 7 millimeter and 21 millimeter socket and ratchet, a pair of pliers, jack and jack stands, a hammer, and a torque wrench.
Start by removing the wheel cover or whatever wheel trim you might have. This one has a chrome one. Pull that off, and then, just use your socket and pull or loosen the lug nut covers. Pull the center cap off. If you don't have the benefit of air tools, you'll want to loosen the lug nuts with the vehicle on the ground. Then, jack up and secure the vehicle and remove the lug nuts, wheel, and tire.
Now, what you want to do is angle the wheel so you can get back to the outer tie rod. Now, using an adjustable wrench and a piece of pipe, you want to loosen the tie rod. Using a 21 millimeter socket, you want to remove that castle nut at the top of the ball joint. This one didn't have a pin through it to secure it, but typically, they do. All you want to do is straighten out the pin and pry it out. Now, using a hammer, you just want to hit the knuckle. Just repeatedly hit it until that bolt loosens up and pull the tie rod free. Before you remove the tie rod, make sure you know what the length of it is. Just measure this distance. Now, you can spin the outer tie rod off.
The old one is on the right, with the new outer tie rod on the left from 1A Auto. You can see it's an exact match. It comes with everything you need for installation. Now, using a 7 millimeter socket and ratchet, you just want to make sure you tighten this up. Then, twist the outer tie rod back onto the inner tie rod. Now, you want to re-measure it and make sure it's the right distance. Then, you want to line up the knuckle with the bolt on the ball joint. Push it up through and replace your castle nut. Push the pin through the bolt and the castle nut. You just want to use pliers to pry the ends of the pin. Now using your adjustable wrench, just tighten that back up.
We'll just fast forward as he puts the wheel back on. You want to replace the lug nuts while it's up in the air. Tighten them. Lower the vehicle. Tighten them the rest of the way and then torque them to 100 foot-pounds. Then, you want to put back on your hubcap. Tighten the lug nut caps and replace your wheel cover.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Product Reviews
Loading reviews
4.00/ 5.04
4 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
3
0
0
0
1
Good refund process
Naomi
March 18, 2018
We received an empty box. When I called to see if they could send me a new order they told me that the kit I ordered was out of stock but they could piece mill a kit together. They could fill the kit with an exception of two pieces and it was going to cost me more then the original price by about $60. On a better note the refund process was quick.
Richard
May 3, 2018
It was everything it advertised as.xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Steering & suspension kit
G
November 4, 2020
Parts came in very quick and well packed
I use only part of the kit but Ill do the rest later
Every thing fits very good ,easy exchange .
Ill strongly recommend to everyone who wants a good parts for reasonable price
No problem ever on Chevy parts
Raul
May 5, 2022
Perfect fit would recommend
Customer Q&A
Are they greasable ?June 8, 2020
Tiffany W
10
Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.
June 8, 2020
T I
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
GMC is a registered trademark of General Motors Company. 1A Auto is not affiliated with or sponsored by GMC or General Motors Company.See all trademarks.
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.