Replaces
This part doesn’t fit a . Select from parts that fit.
Specify your vehicle's year, make and model to guarantee fit.
Frequently bought together
Specify your vehicle's year, make and model to guarantee fit.
If your vehicle isn't listed, search Steering & Suspension Kits
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
Created on:
Tools used
Tools used
Tools used
Tools used
Tools used
Tools used
Tools used
Once you've safely raised and supported your vehicle so you can see underneath, you wanna remove this plate. If you take out these two bolts, this should swing down far enough to see right there. Let's use our 15-millimeter socket to remove this plate as well. That way there we'll have some room to get into the front end with our pickle fork. Remove this.
The next thing we're gonna do is remove this nut right here. Use your 22-millimeter socket. Now that we have the nut off right here, we're gonna come right from this side with our pickle fork and we're gonna try to separate this joint right here. If you wanna spray it with some penetrant, it's probably a great idea. There we go.
Okay, so I've got my ratchet with my extension and my 18-millimeter going through the frame holding that bolt side. The next thing I wanna do is remove the nut on the inside area of the frame. Let's do the same to all three mounting bolts. Now let's just push these bolts in a little bit. Obviously, we don't want them to fall out into the frame. If they do, you just use a magnet, you can grab them out. But by pushing them in at least towards the frame. Oh, it fell into the frame like I said it would. Now we can lift this up and out of here.
Now it's gonna be time to get this together. It comes with a locking nut, so you don't necessarily have to use any thread locker. Put this arm so that the stud is facing down, just like this. Take your nut. If you were to look inside there, you can see that there's an Allen head socket, so we'd use the according Allen head. Can hold the center, and then we're gonna turn the nut using a 24-millimeter wrench until it's nice and tight. Okay, bottomed out right there. Give it a couple extra bonks here. That's nice and tight.
So it's a great idea to use a magnet from the outside of the frame and take out at least two of those bolts that are up there. I like to leave just one. That way there it's a couple less things that I have to worry about pushing through as I get this up and lined up. It's much better to just have one up there. I can have a socket with an extension holding it still, and I'll get that one kind of snugged up a little bit, and then I'll start on the others.
I'm gonna get this shaft right inside this arm. That's gonna be the super important part. Okay, now I'm gonna twist this until all the rest of it lines up, right about like that. Now, I'm gonna use my extension from the other side, I got it through already, see if I can turn this in, get it started. There we go. That one's through. I'm gonna start the nut on there real quick. Should come with a washer. If it came with a washer, the washer goes on the bolt, and then, of course, the nut. It's a great idea to use a little bit of thread locker as well. Goes right up on there. Now there's no chance for this bolt to fall out. Let's continue on by doing the same to the other two. So now it's time to snug these up. I've got my 18-millimeter wrench on the bolt end through the frame there, and I'm gonna go ahead and use my 18-millimeter swivel socket to snug these up. That's nice and tight. Do the same to all three.
Okay, all three are nice and tight. That looks great. Let's move along to torque this to 40 foot-pounds. All right, let's do the same to all the rest. Let's get this on here. We're just gonna snug it up, and then we're gonna torque it to 40 foot-pounds. That's 40. Now you just wanna make sure that the slots on your castle nut are lined up with the hole that goes through here for the cotter pin. Once it's lined up, you put it through and make sure you lock it down. If it isn't lined up, you need to continue tightening until it is. Let's get that locking cotter pin in here. Slides right through. Like I said, make sure you peen it over that way there there's no way this nut can come loose. All right, let's get the plate up here. Let's go ahead and get our shield up here.
Tools used
Tools used
Once you've safely raised and supported your vehicle so you can see underneath, you wanna remove this plate. If you take out these two bolts, this should swing down far enough to see right there. Let's use our 15-millimeter socket to remove this plate as well. That way there we'll have some room to get into the front end with our pickle fork. Remove this.
The next thing we're gonna do is remove this nut right here. Use your 22-millimeter socket. Now that we have the nut off right here, we're gonna come right from this side with our pickle fork and we're gonna try to separate this joint right here. If you wanna spray it with some penetrant, it's probably a great idea. There we go.
Okay, so I've got my ratchet with my extension and my 18-millimeter going through the frame holding that bolt side. The next thing I wanna do is remove the nut on the inside area of the frame. Let's do the same to all three mounting bolts. Now let's just push these bolts in a little bit. Obviously, we don't want them to fall out into the frame. If they do, you just use a magnet, you can grab them out. But by pushing them in at least towards the frame. Oh, it fell into the frame like I said it would. Now we can lift this up and out of here.
Now it's gonna be time to get this together. It comes with a locking nut, so you don't necessarily have to use any thread locker. Put this arm so that the stud is facing down, just like this. Take your nut. If you were to look inside there, you can see that there's an Allen head socket, so we'd use the according Allen head. Can hold the center, and then we're gonna turn the nut using a 24-millimeter wrench until it's nice and tight. Okay, bottomed out right there. Give it a couple extra bonks here. That's nice and tight.
So it's a great idea to use a magnet from the outside of the frame and take out at least two of those bolts that are up there. I like to leave just one. That way there it's a couple less things that I have to worry about pushing through as I get this up and lined up. It's much better to just have one up there. I can have a socket with an extension holding it still, and I'll get that one kind of snugged up a little bit, and then I'll start on the others.
I'm gonna get this shaft right inside this arm. That's gonna be the super important part. Okay, now I'm gonna twist this until all the rest of it lines up, right about like that. Now, I'm gonna use my extension from the other side, I got it through already, see if I can turn this in, get it started. There we go. That one's through. I'm gonna start the nut on there real quick. Should come with a washer. If it came with a washer, the washer goes on the bolt, and then, of course, the nut. It's a great idea to use a little bit of thread locker as well. Goes right up on there. Now there's no chance for this bolt to fall out. Let's continue on by doing the same to the other two. So now it's time to snug these up. I've got my 18-millimeter wrench on the bolt end through the frame there, and I'm gonna go ahead and use my 18-millimeter swivel socket to snug these up. That's nice and tight. Do the same to all three.
Okay, all three are nice and tight. That looks great. Let's move along to torque this to 40 foot-pounds. All right, let's do the same to all the rest. Let's get this on here. We're just gonna snug it up, and then we're gonna torque it to 40 foot-pounds. That's 40. Now you just wanna make sure that the slots on your castle nut are lined up with the hole that goes through here for the cotter pin. Once it's lined up, you put it through and make sure you lock it down. If it isn't lined up, you need to continue tightening until it is. Let's get that locking cotter pin in here. Slides right through. Like I said, make sure you peen it over that way there there's no way this nut can come loose. All right, let's get the plate up here. Let's go ahead and get our shield up here.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts, and the best service on the Internet.
This is part two of doing the Pitman Arm on this '96 Tahoe, which is the same as any '88 -'98 GM truck, or '92 - '99 SUV with four-wheel drive. Again, a little refresher on the tools that you'll need.
Believe it or not, I actually forgot to film... or, I actually messed up and I didn't film pulling the Pitman Arm off, so I'm just going to show you how to use the Pitman Arm puller and the tool on - this is actually the idler arm. This is the same idea, you would just be doing it on the steering box. You put the tool on like that, and then put your wrench on there and pull it, and that breaks it right free. Once we've used the puller, we can take the old arm off and put the new one on. There are four marks, or four larger teeth that make sure that you put the arm on in the right position. The best thing is just take the old one right off and then put the new one right back on in the same position. That way, you know that you have it centered correctly.
We'll put the big lock washer back on... actually, what we might want to do is put the nut on first, tighten it a little bit, which presses the arm on, and then take it off of the lock washer. Then, right up in here you can see, here's our steering coupler. The bolt is to the frame side, and it's basically straight up and down, so you want to have your steering box ready to go the same way. So, it's ready to go up in there. This flat spot here is what aligns with that bolt, so then, basically, take your box and put it in there. Now we've got our steering box up in there. Now take a bolt, feed it through, and you can see it come out on this side. Try and position the steering box so the bolt will go in, and then once you've got the bolt started, just reach up on top of the steering box, make sure your hoses are free - they're not pinched in between the frame and the box. Wrap the third one here.
Here's that Pitman Arm, and here's where it hooks into our steering, and while we still have the box loose a little bit, just move that all into place, and then just start this nut on there for right now. Before you actually tighten up the steering box to the frame, you'll want to connect your linkage here. You can see right down there is the end of the steering box, and this, I have this rubber boot pulled back. This telescopes back and forth, and what you want to do is, you can see there's a flat spot here on the gear, and then there's also a flat spot in your coupler, which I have right at the top now, so you basically want to push your shaft down on there and lid on. Then, put the bolt in, and you want to tighten this bolt up to about 35- 40 foot-pounds. Okay, we've reconnected and tightened both the power steering hoses, and they are different-sized fittings, so you shouldn't have any problem.
I'm going to torque these bolts to 120 foot-pounds. I'm going to torque this nut to 80 foot-pounds. I'm going to put in our new Pitman Arm came with a cotter pin and lock it, and it looks like I need to tighten it another quarter turn. I push the cotter pin through and pull it down around to lock it. Obviously, you're going to want to put your wheel back on, and when it's down on the ground, you're going to want to torque those lug nuts to 120 - 140 foot-pounds. Now, here I am adding some power steering fluid and, basically, you want to fill it to the level it's supposed to be, turn the car on, turn the steering wheel back and forth a few times, and then refill it until it's at the right levels. Then the last step is some grease on this fitting, and it should be all set.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts, and the best service on the Internet. Please feel free to call us toll free: 888-844-3393. We're the company that's here for you on the Internet, and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years' experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
In this video we're going to install a new Pitman arm on this 1996 Tahoe. It is the same as any 1988 to 1998 Chevy truck. This is a four-wheel drive vehicle. So four wheel drive trucks and also 1992 to 1999 SUVs, four-wheel drives.
You will need the following tools: penetrating oil, a whole host of mm sockets, 18-mm fitting wrench, joint fork and hammer Pitman arm puller and actually not listed here was a 19-mm socket and ratchet or your tire iron to remove your tire. You'll also need a jack and jack stand or lift.
To check and see if you have a bad Pitman arm you can see where this front driver's side tire we're going up and under. Here's your transfer to here and then up right there is the joint of your Pitman arm. This here is your Pitman arm and then this is your steering linkage. Again, here is your Pitman arm. Here's your steering linkage. Now when you move your tires, I'm just grabbing hold of the tires and kind of turning them back and forth when the car is above the ground and you can see there is a lot of play and movement going on around that Pitman arm. That joint is bad.
First, you'll want to remove this skid plate which is four 15-mm bolts. You can see two easy here, and there's one up here and one you cannot really see, but over here. Now we're going to remove the steering box to get to the Pitman arm. Okay. So, this is the driver's side of the engine compartment. There's the power break booster and this right down here is your steering box. It's a little difficult to see. It's where you can see these tubes going in. There is a plastic shield here. It kind of clips around. Now you can see this was clipped up and around here. You just kind of peel that off and pull this plastic shield back and now you're going to want to use some penetrating oil and douse both your fittings, one here and then one a little further up. It's kind of difficult to see.
There are two fittings to douse with penetrating oil and then there's also a bolt. You might be able to barely see there and then you also want to loosen this bolt here and that loosens the coupler from the steering box shaft. The best tool for removing those power steering fittings is a fitting wrench like this, 18 mm. See it down on there? I got it on there and then once you loosen it with a fitting wrench you can usually get an open-end wrench on there to help you navigate it the rest of the way.
Then, make sure you have a catch pan underneath to catch the fluid as it starts leaking out. Now we're going to use an 11-mm socket and ratchet and extension to loosen that bolt. Down in there put the socket and ratchet on there. At this point it might be good to have someone help you just hold the steering wheel so it keeps that from turning at all. Once you remove the bolt then you want to take a large screwdriver or a pry bar and put it down in there and just make sure that you can move the steering shaft away from the steering box and if you watch you can see that the shaft is moving from the steering box pretty easily. When I actually unbolt the steering box I'll be able to pull it right out.
No from underneath here's the front of our transfer case on this four-wheel drive truck and this is our Pitman arm joint right here. So, it's a 21-mm bolt. I'll use an impact wrench. As you can see we removed the tire over here and this is a joint fork. So, we're going to bring it in from the side here and then use a good hammer. Basically we just removed the tire so we can get a good wrap on this fork. Okay. You see that fork just separates that joint. Now we get to the three bolts that hold your steering box on and I just used a little screwdriver kind of bend this fender up a little bit because it was in the way and you can just tap it back down with a hammer when you're done. Then you can easily get a socket and extension on there, and just to show you it can be done with hand tools, again, 21-mm. I'll just do the rest of it with an impact wrench just to be quicker.
Hold on to the box with one hand. If not it's just going to fall out. Move it up and out of the steering gear and pull it forward from the shaft. Here's the bottom of it. Put the steering box here, upside down, once again just so any more fluids just drain out into the pan. Here's where having an impact wrench is going to be really valuable. Then this socket is a 34 mm. If you don't have an impact you can just turn it on all the way and then use a large bar. You may want someone to help hold it. You could bolt your steering box onto a longer piece of wood which would help you to keep it steady, but having an impact wrench is the best way. Now, you're going to want to use your Pitman arm puller. This is really the only way to do this.
Believe it or not I actually forgot to film, or I messed up and I didn't film pulling the Pitman arm off so I'm just going to show you how to use the Pitman arm puller and the tool on to the idler arm. It's the same idea. You would just be doing it on the steering box. Put the tool on like that and then put your wrench on there and then pull and it breaks it right free. Okay, and this ends part one of this video. If you want to see, obviously, reinstalling the Pitman arm go please to
part two.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Feel free to call us toll free, 888-844 3393. We're the company that's here for you on the internet and in person. Thank you.
877-844-3393
Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET
Specify your vehicle's year, make and model to guarantee fit.
This part doesn’t fit a . Select from parts that fit.
Before proceeding,
select your Vehicle, to verify this Part will fit.
If your vehicle isn't listed, search Steering & Suspension Kits
This part will only fit a 2000 GMC K3500 Truck with these options.