Replaces
Part Details
TRQ suspension kits are manufactured using premium raw materials and coatings for extended service life. Each TRQ suspension component is designed to be a direct, maintenance-free replacement to the stock unit. To extend the life of your steering and suspension components, TRQ recommends replacing components in pairs, sets, or kits. All products are fit and road-tested in our Massachusetts R&D facility to ensure we deliver on our promise of Trusted Reliable Quality.
Product Features
Install Tip: When replacing steering components, have a professional alignment performed afterwards. This ensures proper tracking and even tire wear.
Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, I'm going to replace an inner tie rod on this 2002 GMC Sierra. This procedure is the same for millions of GMC Sierra, Chevy Silverado, 1500 and 2500, 3500, pretty much all the same basic procedure. You'll need a couple of large adjustable wrenches. I found those work fine. You don't really need the exact size. Two large adjustable wrenches will work.You'll also need a tape measure and you'll need a grease gun with grease, and we do recommend that you have your vehicle aligned after a repair like this.
Here you can see, I have the vehicle up on a lift. Here is my inner tie rod running from here to here. This is the outer tie rod. You could see, I pull this boot down and I pull and what I'm looking at is basically the relationship of here to here and I can see some movement in here. I want to replace this. What I'm going to do is, I'm going to pull out, then I'm going to measure from there to there. Just a shade under ten inches, 9 and 15/16"?. Now, I'm going to pull it back in, and check here. It's about 9 and 7/8"?. When I put this back together, I'm going to set this right between 9 and 7/8"? and 9 and 15/16"?. I'm going to pull it apart. I'm just going to clean this off.
Take a nice big adjustable wrench. I'm loosening that up. On this end, I'm going to put a wrench on my outer tie rod just to hold it in place. We'll get that loosened up. I'm just going to speed up here. We loosened up the nut that's close to the center steering rack and then we loosened up the tie rod where it connects the outer tie rod. Take that nut off for the center steering first and then just turn the whole entire inner tie rod counter clockwise and take it out of the outer tie rod.
Here's a new tie rod from 1A Auto. It's always a good idea to put some thread lock on the inside. If you have your vehicle up on a lift, or a jack, you'll want to jack it up just to get, make sure your stabilizer bars up and out of the way. Thread it in and then use a wrench and tighten this. This should be tightened to 74 foot-pounds. Anywhere between 70 and 80 foot-pounds. In this shot, what I didn't explain very clearly, you can see where that red arrow is. I have a jack underneath the suspension. It just helps lift it up so that the stabilizer bar isn't in the way when you start the tie rod into the center steering link. With this wrench, just pull it nice and tight. Now I'm going to assemble the outer end. I'm going to put this nut on. Then to bring this down on my tire and in. Make sure it's going together straight. If you remember our measurement, basically, we want to be right at 9 and 31/32, so we've got a long way to go. I'm going to speed it up here as I keep using the wrench to turn the tie rod end into the outer tie rod end. I measured a couple of times just to see where I'm at. That is, it's just a little bit further than we want. Knock it off, right there. We've got our one wrench on here and then to tighten, hold on to the outer tie rod, taking that up nice and secure. Now make sure we grease the fitting. What I'm watching, I'm watching this boot here. Once that boot starts changing shape a little bit, I know the grease is in there. Then, while on here. I'm going to hit all my other grease spots as well.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
In this video, we're going to show you how to replace an outer tie rod on this 2005 GMC Savana 2500. It's the same process on the Savanas from 2001 to 2006, as well as a large variety of GM trucks and vans. The tools you'll need are an adjustable wrench, a piece of pipe for leverage, a 7 millimeter and 21 millimeter socket and ratchet, a pair of pliers, jack and jack stands, a hammer, and a torque wrench.
Start by removing the wheel cover or whatever wheel trim you might have. This one has a chrome one. Pull that off, and then, just use your socket and pull or loosen the lug nut covers. Pull the center cap off. If you don't have the benefit of air tools, you'll want to loosen the lug nuts with the vehicle on the ground. Then, jack up and secure the vehicle and remove the lug nuts, wheel, and tire.
Now, what you want to do is angle the wheel so you can get back to the outer tie rod. Now, using an adjustable wrench and a piece of pipe, you want to loosen the tie rod. Using a 21 millimeter socket, you want to remove that castle nut at the top of the ball joint. This one didn't have a pin through it to secure it, but typically, they do. All you want to do is straighten out the pin and pry it out. Now, using a hammer, you just want to hit the knuckle. Just repeatedly hit it until that bolt loosens up and pull the tie rod free. Before you remove the tie rod, make sure you know what the length of it is. Just measure this distance. Now, you can spin the outer tie rod off.
The old one is on the right, with the new outer tie rod on the left from 1A Auto. You can see it's an exact match. It comes with everything you need for installation. Now, using a 7 millimeter socket and ratchet, you just want to make sure you tighten this up. Then, twist the outer tie rod back onto the inner tie rod. Now, you want to re-measure it and make sure it's the right distance. Then, you want to line up the knuckle with the bolt on the ball joint. Push it up through and replace your castle nut. Push the pin through the bolt and the castle nut. You just want to use pliers to pry the ends of the pin. Now using your adjustable wrench, just tighten that back up.
We'll just fast forward as he puts the wheel back on. You want to replace the lug nuts while it's up in the air. Tighten them. Lower the vehicle. Tighten them the rest of the way and then torque them to 100 foot-pounds. Then, you want to put back on your hubcap. Tighten the lug nut caps and replace your wheel cover.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts, installed correctly that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to replace the sway bar links in this 2002 GMC 2500HD, basically the same as most '88 to '06 GM pickups, SUVs, vans; also the same as a couple of Ford applications. Tools you'll need are a jack and jack stands for some vehicles, 14 mm socket and ratchet or whatever is correct for your link, they could be different depending on application, an adjustable wrench, and some penetrating oil.
Your stabilizer link is right up underneath. This big bar here is your stabilizer bar, and then here is your control arm. It's connected by this, which is the stabilizer link right here. This can break. Also, these bushings, these rubber bushings can wear out, which will cause a rattling sometimes when you go over bumps. You have a good idea if it's the stabilizer link if, when you go around a turn, the rattling stops. I'm going to show you how to replace that.
On top, you're going to want to spray some penetrating fluid. This is a 14 mm bolt down here at the bottom. What you're going to want to do is put an adjustable wrench onto this side. This is an original link here, so the thing on top is kind of bolt-shaped. I've got that on there to hold it. Now I'm going to attempt to slowly unscrew it.
The bolt comes down, and that can come out. Then you can see, even though there's nothing too terribly wrong, you can see that this one is worn, right in here, so we'll replace it. On the original you can see this top nut has edges to it so you can get that wrench on there to hold it in place. We've gotten it out of there, but we still have this in place. Just pull that right out, like that. I'm going to take my new link and I'm going to put it up through. This bushing has the ridge up into the control arm. Then I'm going to take a bushing down and then a washer on top of that, then my spacer. Then I'm going to take a bushing and a washer, and now the step goes up into the sway bar. Then just push that.
In order to get this in, what I've done is this is a little jack. If you're doing this just on the ground, you can do the same thing. Put the jack in underneath the stabilizer bar here, lift it up, and create plenty of room to push that up through. Then you want to make sure these bushings all go right into the holes in the stabilizer bar, right there, and the control arm. This last bushing goes with the ridge down, then the washer on top. I'm going to put the jack right in underneath here, push this up in to get the nut on.
I've got this together and I've got the nut started on there. I'm going to replace the other side first before I tighten it up. I wouldn't take apart the other side here you can see, this is the one from the driver's side and this is the one from this side, so you can see this whole part was rough and it broke off. It's possible this link wasn't really doing anything anyways. This here that broke off of this one is stuck inside there. What I'm going to have to do is I'm going to have to actually cut this link with my Sawzall. I'm going to do that very carefully, because I don't want to contact the boot or anything else. I don't want to contact the CVs. I just want to cut through the link itself.
Now with the car on the ground, you want to tighten up the links. I'm just using an air ratchet. You can hand tools, obviously. Tighten up both sides and you're done.
We hope this helps you out. Brought to you by www.1AAuto.com- your source for quality replacement parts and the best service on the internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the internet and in person.
